We use JE pistons and rings with a clearance of 2.5 thou. Which I think is
about 1/2 of a thou. Less than Chris uses.
John H. Hasty
Attorney At Law
Guthrie, Davis, Henderson & Staton, P.L.L.C.
719 East Boulevard
Charlotte, North Carolina 28203-5113
Tele: (704) 372-5600
Fax: (704) 372-4601
E-mail: jhhasty@gdhs.com
www.gdhs.com
PRIVILEGE AND CONFIDENTIALITY NOTICE: This message (and any attachments) is
intended only for the use of the addressee and may contain information that
is PRIVILEGED and CONFIDENTIAL, and/or may contain ATTORNEY WORK PRODUCT.
If you are not the intended recipient, you are hereby notified that any
dissemination of this communication is strictly prohibited. If you have
received this communication in error, please erase all copies of the message
and its attachments and notify us immediately. Thank you.
IRS CIRCULAR 230 NOTICE: In order to comply with certain IRS regulations
regarding tax advice, we inform you that, unless expressly stated otherwise,
any tax advice contained in this communication (including any attachments)
is not intended or written to be used, and cannot be used, for purposes of
(i) avoiding penalties under the Internal Revenue Code or (ii) promoting,
marketing or recommending to another party any transaction or matter
addressed herein.
-----Original Message-----
From: fot-bounces@autox.team.net [mailto:fot-bounces@autox.team.net] On
Behalf Of MadMarx
Sent: Tuesday, September 11, 2012 11:24 AM
To: fot@autox.team.net
Subject: Re: [Fot] Never be beaten by equipment
I had the same trouble with Wiseco pistons.
Maybe they expand a lot.
I run as piston to wall clearance 0.13mm.
Never believe what the piston manufacturer says.
Won't work on a wet liner Triumph engine.
The liners deform under heat and getting oval.
More clearance is needed as normal.
At the current engine I try to install old liners in the same direction when
they were installed the first time in hope the deformation is smaller.
Chris
-----Urspr|ngliche Nachricht-----
Von: fot-bounces@autox.team.net [mailto:fot-bounces@autox.team.net] Im
Auftrag von Robert Blake
Gesendet: Dienstag, 11. September 2012 17:08
An: fot@autox.team.net
Betreff: [Fot] Never be beaten by equipment
Pops and I had a less than excellent weekend at TWS it would true to say
that we were beaten by equipment, one of us physically.
We just put a new engine
in Dads #14. The second one since December. We built this one with Wiseco
pistons, stock liners bored to 87+.005 on 1-3 and +.006 on number 4. This
resulted in the engine lasting most of the day Friday for test and tune. On
his last run we did a plug check. We had been trying to dial in his mixture
all day and moving from a lean condition as evidenced by previous plug cuts
in the day. After adjusting the mixture, reinstalling the plugs, gapping
points, and rechecking timing we started the engine to hear a horrible
clatter from within. Same clatter that dad had heard at the Mitty so we
feared the worst.
Later that evening he and Bob Kramer confirmed that #4 piston skirt was
scuffed again. The same thing happened on the previous engine at the Mitty.
Oil pressure was great all day (80 psi from 3000rpm up) the water temp never
went above normal range.
So other than lack of piston to liner clearance, what causes pistons skirts
to scuff on the liner? Can a lean mixture on the rear carb cause this
without showing up as a hot running condition?
On to my
issue.
My aluminum hood pins broke on the TR3 on the back straight.
Unfortunately, the passenger hinge snapped but the drivers side did not. The
hood bent back and slapped my helmet pretty good (beaten by my equipment).
Never thought of it that way before. Not pleasant. So I am in search of a
decent bonnet. It is for a 58 TR3A. I am not too picky but proximity to TX
is a major consideration.
Info on both issues is appreciated.
Greg
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Unsubscribe:
http://autox.team.net/mailman/options/fot/tr4racing@googlemail.com
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/fot/jhhasty@gdhs.com
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Unsubscribe:
http://autox.team.net/mailman/options/fot/fot-archive@autox.team.net
|