--===============9142480203787778077==
Content-Transfer-Encoding: 7bit
--Apple-Mail-C965D222-F6D7-49FB-898D-0BFCFD834078
charset=utf-8
Content-Transfer-Encoding: quoted-printable
So here=E2=80=99s the big picture=E2=80=A6 I=E2=80=99ve had this ticka ticka=
ticka noise coming from the right side of the car, hard to hear it at highw=
ay speed, but 45 mph and below it=E2=80=99s there. Easy to hear when reflect=
ed off a railing or wall. A slight pressure on the brake pedal stops it. So I=
figure it's the brake pad jumping up and down. Brake pads are within spec. B=
oth rotors were way too thin. Replaced them but still have the ticka ticka. I=
will put new pads on.
Also =E2=80=9Cfound=E2=80=9D the disappearing brake fluid (only after a driv=
e) was due to the brake booster. So now that=E2=80=99s off the car. The cali=
pers are aftermarket, unknown age by previous owner. Heck, might as well reb=
uild those since I=E2=80=99ll have to bleed anyway.
So I have these original calipers on an inside storage parts car. Well, one i=
s off with one piston loose so far. I was thinking of using those original c=
alipers, if I can get all the pistons out. If so, should I separate the cali=
pers to replace that seal or leave it alone?
Dan
Sent from my iPad
> On Nov 14, 2025, at 5:36 PM, Jake V <britishauto@gmail.com> wrote:
>=20
> =EF=BB=BF
> Depends on the preload you want on the tension bolts that hold the caliper=
halves together.=20
> Definitely do your own research if you're planning to split the calipers. I=
t's not that hard to estimate the system pressure.
>=20
>> On Fri, Nov 14, 2025, 5:20 PM Richard Mayor <boyracer466@gmail.com> wrote=
:
>> Those numbers seem like overkill. There are charts that have the appropr=
iate torque for the various size fasteners. I would consult one of those ch=
arts.
>>=20
>>=20
>> Sent from my iPad
>>=20
>>>> On Nov 14, 2025, at 12:32=E2=80=AFPM, Jake V <britishauto@gmail.com> wr=
ote:
>>>>=20
>>> =EF=BB=BF
>>> Type 16P is correct, that's what you're showing. You'll want to get the s=
eal between the halves as well, it's not included in the rebuild kit.=20
>>> Bolt torque recommendations are 75ft-lb for the =C3=987/16 pair and 45ft=
-lb for the =C3=983/8 pair.=20
>>> Caveat: Those torque numbers aren't available from the manual, some TR6s=
used the same 16P calipers. I found a thread with that info from TRF tech a=
ssistance.
>>>=20
>>> https://mossmotors.com/583-820-seal-between-caliper-halves?qty=3D1
>>>=20
>>>> On Fri, Nov 14, 2025 at 12:36=E2=80=AFPM <dwernervt@gmail.com> wrote:
>>>> Looking to verify that this is an original caliper as I need to order t=
he correct repair kit and SS pistons.
>>>> Thanks!
>>>> Dan Werner=20
>>>>=20
>>>>=20
>>>>=20
>>>>=20
>>>>=20
>>>>=20
>>>>=20
>>>>=20
>>>>=20
>>>> Sent from my iPad_______________________________________________
>>>> Support Team.Net http://www.team.net/donate.html
>>>> Suggested annual donation $12.75
>>>>=20
>>>> Archive: http://www.team.net/pipermail/healeys http://autox.team.net/ar=
chive/healeys
>>>>=20
>>>> Healeys@autox.team.net
>>>> http://autox.team.net/mailman/listinfo/healeys
>>>>=20
>>>> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/briti=
shauto@gmail.com
>>>>=20
>>> _______________________________________________
>>> Support Team.Net http://www.team.net/donate.html
>>> Suggested annual donation $12.75
>>>=20
>>> Archive: http://www.team.net/pipermail/healeys http://autox.team.net/arc=
hive/healeys
>>>=20
>>> Healeys@autox.team.net
>>> http://autox.team.net/mailman/listinfo/healeys
>>>=20
>>> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/boyrac=
er466@gmail.com
>>>=20
--Apple-Mail-C965D222-F6D7-49FB-898D-0BFCFD834078
charset=utf-8
Content-Transfer-Encoding: quoted-printable
<html><head><meta http-equiv=3D"content-type" content=3D"text/html; charset=3D=
utf-8"></head><body dir=3D"auto">So here=E2=80=99s the big picture=E2=80=A6 I=
=E2=80=99ve had this ticka ticka ticka noise coming from the right side of t=
he car, hard to hear it at highway speed, but 45 mph and below it=E2=80=99s t=
here. Easy to hear when reflected off a railing or wall. A slight pressure o=
n the brake pedal stops it. So I figure it's the brake pad jumping up and do=
wn. Brake pads are within spec. Both rotors were way too thin. Replaced them=
but still have the ticka ticka. I will put new pads on.<div>Also =E2=80=9Cf=
ound=E2=80=9D the disappearing brake fluid (only after a drive) was due to t=
he brake booster. So now that=E2=80=99s off the car. The calipers are afterm=
arket, unknown age by previous owner. Heck, might as well rebuild those sinc=
e I=E2=80=99ll have to bleed anyway.</div><div>So I have these original cali=
pers on an inside storage parts car. Well, one is off with one piston loose s=
o far. I was thinking of using those original calipers, if I can get all the=
pistons out. If so, should I separate the calipers to replace that seal or l=
eave it alone?</div><div>Dan</div><div><br><div dir=3D"ltr">Sent from my iPa=
d</div><div dir=3D"ltr"><br><blockquote type=3D"cite">On Nov 14, 2025, at 5:=
36 PM, Jake V <britishauto@gmail.com> wrote:<br><br></blockquote></div=
><blockquote type=3D"cite"><div dir=3D"ltr">=EF=BB=BF<div dir=3D"auto">Depen=
ds on the preload you want on the tension bolts that hold the caliper halves=
together. <div dir=3D"auto">Definitely do your own research if you're p=
lanning to split the calipers. It's not that hard to estimate the system pre=
ssure.</div></div><br><div class=3D"gmail_quote gmail_quote_container"><div d=
ir=3D"ltr" class=3D"gmail_attr">On Fri, Nov 14, 2025, 5:20 PM Richard Mayor &=
lt;<a href=3D"mailto:boyracer466@gmail.com";>boyracer466@gmail.com</a>> wr=
ote:<br></div><blockquote class=3D"gmail_quote" style=3D"margin:0 0 0 .8ex;b=
order-left:1px #ccc solid;padding-left:1ex"><div dir=3D"auto">Those numbers s=
eem like overkill. There are charts that have the appropriate torque f=
or the various size fasteners. I would consult one of those charts.<di=
v><br></div><div><br id=3D"m_4462736351559814321lineBreakAtBeginningOfSignat=
ure"><div dir=3D"ltr">Sent from my iPad</div><div dir=3D"ltr"><br><blockquot=
e type=3D"cite">On Nov 14, 2025, at 12:32=E2=80=AFPM, Jake V <<a href=3D"=
mailto:britishauto@gmail.com"; target=3D"_blank" rel=3D"noreferrer">britishau=
to@gmail.com</a>> wrote:<br><br></blockquote></div><blockquote type=3D"ci=
te"><div dir=3D"ltr">=EF=BB=BF<div dir=3D"ltr">Type 16P is correct, that's w=
hat you're showing. You'll want to get the seal between the halves as well, i=
t's not included in the rebuild kit. <div>Bolt torque recommendations a=
re 75ft-lb for the =C3=987/16 pair and 45ft-lb for the =C3=983/8 pair. =
</div><div>Caveat: Those torque numbers aren't available from the manual, so=
me TR6s used the same 16P calipers. I found a thread with that info from TRF=
tech assistance.</div><div><br></div><div><a href=3D"https://mossmotors.com=
/583-820-seal-between-caliper-halves?qty=3D1" target=3D"_blank" rel=3D"noref=
errer">https://mossmotors.com/583-820-seal-between-caliper-halves?qty=3D1</a=
></div></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_=
attr">On Fri, Nov 14, 2025 at 12:36=E2=80=AFPM <<a href=3D"mailto:dwerner=
vt@gmail.com" target=3D"_blank" rel=3D"noreferrer">dwernervt@gmail.com</a>&g=
t; wrote:<br></div><blockquote class=3D"gmail_quote" style=3D"margin:0px 0px=
0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Looking t=
o verify that this is an original caliper as I need to order the correct rep=
air kit and SS pistons.<br>
Thanks!<br>
Dan Werner <br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
Sent from my iPad_______________________________________________<br>
er noreferrer" target=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys"; rel=3D"noreferrer=
noreferrer" target=3D"_blank">http://www.team.net/pipermail/healeys</a> <a h=
ref=3D"http://autox.team.net/archive/healeys"; rel=3D"noreferrer noreferrer" t=
arget=3D"_blank">http://autox.team.net/archive/healeys</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; target=3D"_blank" rel=3D"noreferre=
r">Healeys@autox.team.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D"noreferrer=
noreferrer" target=3D"_blank">http://autox.team.net/mailman/listinfo/healey=
s</a><br>
<br>
/britishauto@gmail.com" rel=3D"noreferrer noreferrer" target=3D"_blank">http=
://autox.team.net/mailman/options/healeys/britishauto@gmail.com</a><br>
<br>
</blockquote></div>
<span>_______________________________________________</span><br><span>Suppor=
t Team.Net <a href=3D"http://www.team.net/donate.html"; target=3D"_blank" rel=
=3D"noreferrer">http://www.team.net/donate.html</a></span><br><span>Suggeste=
d annual donation $12.75</span><br><span></span><br><span>Archive: <a h=
ref=3D"http://www.team.net/pipermail/healeys"; target=3D"_blank" rel=3D"noref=
errer">http://www.team.net/pipermail/healeys</a> <a href=3D"http://autox.tea=
m.net/archive/healeys" target=3D"_blank" rel=3D"noreferrer">http://autox.tea=
m.net/archive/healeys</a></span><br><span></span><br><span><a href=3D"mailto=
:Healeys@autox.team.net" target=3D"_blank" rel=3D"noreferrer">Healeys@autox.=
team.net</a></span><br><span><a href=3D"http://autox.team.net/mailman/listin=
fo/healeys" target=3D"_blank" rel=3D"noreferrer">http://autox.team.net/mailm=
an/listinfo/healeys</a></span><br><span></span><br><span>Unsubscribe/Manage:=
<a href=3D"http://autox.team.net/mailman/options/healeys/boyracer466@gmail.=
com" target=3D"_blank" rel=3D"noreferrer">http://autox.team.net/mailman/opti=
ons/healeys/boyracer466@gmail.com</a></span><br><span></span><br></div></blo=
ckquote></div></div></blockquote></div>
</div></blockquote></div></body></html>=
--Apple-Mail-C965D222-F6D7-49FB-898D-0BFCFD834078--
--===============9142480203787778077==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys
http://autox.team.net/archive/healeys
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============9142480203787778077==--
|