<div style="color:black;font: 12pt Arial, Helvetica, sans-serif;">
<div> <font size="3">I went the band-aid route on my TR3 for the same reason.  But the right way is to get a machinist to shorten the pushrods.  BPNW sells short rods for the TR6/SC engine but at that time they didn't have any for the wet-sleeve engine.</font><br>
</div>

<div> <br>
</div>

<div style="clear:both"><font size="4">Dave </font><br>
<br>
</div>

<div> <br>
</div>

<div> <br>
</div>

<div style="font-family:arial,helvetica;font-size:10pt;color:black"><font size="2">-----Original Message-----<br>
From: Cliff Hansen <cliff_hansen@outlook.com><br>
To: list Triumph <triumphs@autox.team.net><br>
Sent: Wed, Apr 7, 2021 4:23 pm<br>
Subject: [TR] Advice on high compression head<br>
<br>

<div id="yiv4309632913">

 
 
<style><!--
#yiv4309632913  
 _filtered {}
 _filtered {}
#yiv4309632913  
#yiv4309632913 p.yiv4309632913MsoNormal, #yiv4309632913 li.yiv4309632913MsoNormal, #yiv4309632913 div.yiv4309632913MsoNormal
        {margin:0in;font-size:11.0pt;font-family:"Calibri", sans-serif;}
#yiv4309632913 a:link, #yiv4309632913 span.yiv4309632913MsoHyperlink
        {color:blue;text-decoration:underline;}
#yiv4309632913 .yiv4309632913MsoChpDefault
        {}
 _filtered {}
#yiv4309632913 div.yiv4309632913WordSection1
        {}
--></style>


<div>

<div class="yiv4309632913WordSection1">

<div class="yiv4309632913MsoNormal">The telenovela “What’s going on with this 4A cylinder head” has developed a new plot twist.</div>


<div class="yiv4309632913MsoNormal">  </div>
 

<div class="yiv4309632913MsoNormal">The head, after cleanup, measures 3.21” from bottom to the surface for the valve cover gasket. Stock is 3.330 (if I got the number correctly). Some PO cut 0.11 off, because only 0.010” was removed in this round of clean up. Now I can see
 an explanation for the persistent pinging I’ve dealt with over the last few years (head has been milled so compression is high, material near intake valves has been thinned, increasing likelihood of hot spots – I’m getting this from Kastner’s preparation book),
 which I had thought was due to leaking intakes, carb shafts, or operating at higher altitude.</div>
 

<div class="yiv4309632913MsoNormal">  </div>
 

<div class="yiv4309632913MsoNormal">As is, I can’t use this head because there is not enough slack in the valve train to give 0.010” clearance on several valves. I didn’t notice before, but now that I am looking, all the valve adjusters were nearly backed out all the way.</div>


<div class="yiv4309632913MsoNormal">  </div>
 

<div class="yiv4309632913MsoNormal">Looking for advice from the list: is there any reasonable way to use this head?</div>


<div class="yiv4309632913MsoNormal">- I’d prefer to reduce compression but don’t see any reasonable way to accomplish that. I called GasketWorks and he gently discouraged me from getting a custom thick head gasket, saying instead I’d be better off finding a head which had
 not been milled so much. </div>


<div class="yiv4309632913MsoNormal"> - Shimming the rocker pedestals to get valve clearance feels like a bandaid which certainly won’t address the pinging (assuming that the pinging is a result of the shortened head).</div>


<div class="yiv4309632913MsoNormal">  </div>
 

<div class="yiv4309632913MsoNormal">Would appreciate any advice on the way forward.</div>


<div class="yiv4309632913MsoNormal">  </div>
 

<div class="yiv4309632913MsoNormal">Cliff</div>


<div class="yiv4309632913MsoNormal">  </div>
 

<div class="yiv4309632913MsoNormal">Sent from <a rel="nofollow noopener noreferrer" target="_blank" href="https://go.microsoft.com/fwlink/?LinkId=550986">
Mail</a> for Windows 10</div>


<div class="yiv4309632913MsoNormal">  </div>
 
</div>

</div>


</div>
** <a ymailto="mailto:triumphs@autox.team.net" href="mailto:triumphs@autox.team.net">triumphs@autox.team.net</a> **<br>
<br>
Donate: <a href="http://www.team.net/donate.html" target="_blank">http://www.team.net/donate.html</a><br>
Archive: <a href="http://www.team.net/pipermail/triumphs" target="_blank">http://www.team.net/pipermail/triumphs </a> <a href="http://www.team.net/archive" target="_blank">http://www.team.net/archive</a><br>
<br>
Unsubscribe/Manage: <a href="http://autox.team.net/mailman/options/triumphs/dave1massey@cs.com" target="_blank">http://autox.team.net/mailman/options/triumphs/dave1massey@cs.com</a><br>
</font></div>
</div>