<div style="color:black;font: 12pt Arial, Helvetica, sans-serif;">
<div> <font size="3">The combustion chamber size will need to be bigger to avoid having a compression ratio of 15:1. OK, maybe a little hyperbolic but the longer stroke needs a larger chamber.  A friend had issues on his TR250 which turned out to be a GT6 head on the 250 block.  Compression was crazy high and the intake manifold didn't quite fit.</font></div>

<div><font size="3"><br>
</font></div>

<div><font size="3">But I agree with you.  There are quite a few TR6 owners with deep pockets (just ask Rich Good) and an OHC inline 6 is way cool.</font><br>
</div>

<div> <br>
</div>

<div style="clear:both"><font size="4">Dave </font><br>
<br>
</div>

<div> <br>
</div>

<div> <br>
</div>

<div style="font-family:arial,helvetica;font-size:10pt;color:black">-----Original Message-----<br>
From: Greg Lemon <grglmn@gmail.com><br>
To: Michael Porter <mdporter@dfn.com><br>
Cc: Triumphs <triumphs@autox.team.net><br>
Sent: Mon, Sep 2, 2019 11:36 pm<br>
Subject: Re: [TR] Aluminum head?<br>
<br>

<div id="yiv5859829621">
<div>
<div>So will an aluminum cross flow GT6 head fit a 2.5 liter too?  If so the offset bonnet bulge club would like to know which side is intake on?
<div><br clear="none"></div>

<div>My work on my high flow cast iron head has kind of stalled out. <br clear="none">
<div><br clear="none"></div>

<div>Greg Lemon</div>

<div>TR250</div>

<div><br clear="none"></div>
</div>
</div>
<br clear="none">
<div class="yiv5859829621gmail_quote">
<div class="yiv5859829621yqt7283203215" id="yiv5859829621yqtfd21208">
<div class="yiv5859829621gmail_attr" dir="ltr">On Mon, Sep 2, 2019, 10:40 PM Michael Porter <<a rel="noopener noreferrer" shape="rect" ymailto="mailto:mdporter@dfn.com" target="_blank" removedlink__7cfab060-b10b-4851-b8b0-0f7bec323e6b__href="mailto:mdporter@dfn.com">mdporter@dfn.com</a>> wrote:<br clear="none"></div>
</div>
<blockquote class="yiv5859829621gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;">
<div class="yiv5859829621yqt7283203215" id="yiv5859829621yqtfd85832">On 9/2/2019 9:11 PM, <a rel="noopener noreferrer" shape="rect" ymailto="mailto:Wbeech@flash.net" target="_blank" removedlink__7cfab060-b10b-4851-b8b0-0f7bec323e6b__href="mailto:Wbeech@flash.net">Wbeech@flash.net</a> wrote:<br clear="none">
> Oh wow, my ‘66 TR4 Motor has an aluminium head, am I doomed?  Discovered a water leak after I bought it, bad weld job on the one of channels in the block that fouled the head seal.  Filed it, fixed it, remember only 70ftlbs on the studs.  ISTR the liners were not as proud of the block as some say they should be.<br clear="none">
<br clear="none">
You've probably averted problems because the liners weren't sticking up <br clear="none">
to spec (especially toward the high side of the tolerance).<br clear="none">
<br clear="none">
It's a curious situation.  The heads aren't wildly popular because of <br clear="none">
the price, so the number of them actually out there is pretty small, <br clear="none">
relatively speaking.  But, they also might be fairly rare because the <br clear="none">
few people that did buy them couldn't get them to seal and, thinking it <br clear="none">
was their fault, that there was something special about the product that <br clear="none">
they didn't understand, and went back to cast-iron heads.<br clear="none">
<br clear="none">
I knew there was at least one person on the list with one, and I think <br clear="none">
two, because I remember a message maybe a couple of decades ago, in the <br clear="none">
early days of the list, from someone having trouble getting one to seal <br clear="none">
properly.<br clear="none">
<br clear="none">
(Not against aluminum heads, at all.  There are advantages to them.  I <br clear="none">
just think, because of the small variability of the figure-eight gaskets <br clear="none">
and the cylinder heights, that they're probably ill-suited, in the <br clear="none">
configuration they're being produced, for wet-sleeve engines.  I've been <br clear="none">
designing, off and on, on a 4-valve OHC head for the GT6 which, now that <br clear="none">
there's machinable wax available for 3D-printers, can be 3D-printed and <br clear="none">
investment-cast.)<br clear="none">
<br clear="none">
<br clear="none">
Cheers.<br clear="none">
<br clear="none">
-- <br clear="none">
<br clear="none">
<br clear="none">
Michael Porter<br clear="none">
Roswell, NM<br clear="none">
<br clear="none">
<br clear="none">
Never let anyone drive you crazy when you know it's within walking distance....<br clear="none">
<br clear="none">
</div>
</blockquote></div>
</div>
</div>
<br>
</div>
</div>