<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:m="http://schemas.microsoft.com/office/2004/12/omml" xmlns="http://www.w3.org/TR/REC-html40"><head><meta http-equiv=Content-Type content="text/html; charset=us-ascii"><meta name=Generator content="Microsoft Word 14 (filtered medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
@font-face
{font-family:Tahoma;
panose-1:2 11 6 4 3 5 4 4 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri","sans-serif";}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:purple;
text-decoration:underline;}
span.EmailStyle17
{mso-style-type:personal;
font-family:"Calibri","sans-serif";
color:windowtext;}
span.EmailStyle18
{mso-style-type:personal-reply;
font-family:"Calibri","sans-serif";
color:#1F497D;}
.MsoChpDefault
{mso-style-type:export-only;
font-size:10.0pt;}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext="edit" spidmax="1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext="edit">
<o:idmap v:ext="edit" data="1" />
</o:shapelayout></xml><![endif]--></head><body lang=EN-US link=blue vlink=purple><div class=WordSection1><p class=MsoNormal><span style='color:#1F497D'>In the first case, those two sets of measurements seem to agree on the upper end – 0.003 x 3.250 = 0.00975. But a total of just 0.003” does seem quite snug.<o:p></o:p></span></p><p class=MsoNormal><span style='color:#1F497D'><o:p> </o:p></span></p><p class=MsoNormal><span style='color:#1F497D'>On the related topic, the question is where does the wear exist? Is it in the cylinder or in the ring. You can always use a telescoping gauge and micrometer to see what the bore actually is. And/or. if you can obtain a sleeve of rings for just one cylinder, install a compression ring by itself, square it to the hole at several locations, and see what you have for ring end gap. Since those are sleeved engines, you could also purchase piston/sleeve kits but that gets expensive. I have found that on tractor engines where someone has installed aftermarket piston/sleeve big bore kits, it may be difficult to find replacement rings for those pistons. What does a compression test tell you on that engine?<o:p></o:p></span></p><p class=MsoNormal><span style='color:#1F497D'><o:p> </o:p></span></p><p class=MsoNormal><span style='color:#1F497D'>Alex Thomson<o:p></o:p></span></p><p class=MsoNormal><span style='color:#1F497D'><o:p> </o:p></span></p><div><div style='border:none;border-top:solid #B5C4DF 1.0pt;padding:3.0pt 0in 0in 0in'><p class=MsoNormal><b><span style='font-size:10.0pt;font-family:"Tahoma","sans-serif"'>From:</span></b><span style='font-size:10.0pt;font-family:"Tahoma","sans-serif"'> Triumphs [mailto:triumphs-bounces@autox.team.net] <b>On Behalf Of </b>Andrew Uprichard<br><b>Sent:</b> Friday, February 12, 2016 4:02 PM<br><b>To:</b> triumphs@autox.team.net<br><b>Subject:</b> [TR] Ring gaps<o:p></o:p></span></p></div></div><p class=MsoNormal><o:p> </o:p></p><p class=MsoNormal>The manual for the TR3 says the ring gap should be 0.003 – 0.010. But I have new pistons and rings marked that the gap should be 0.003 – 0.004 per inch diameter of the bore. 3 thou sounds awfully tight to me, but what do others think?<o:p></o:p></p><p class=MsoNormal><o:p> </o:p></p><p class=MsoNormal>On a related subject, a friend has an engine where the ring gap is 0.040. How much of this could be made up by simply replacing the rings? Or is there a point at which the only solution is bigger pistons +/- rebore?<br><br>Andrew Uprichard<o:p></o:p></p></div></body></html>