[TR] TR3 O/D Solenoid plate
Paul Tegler
ptegler at verizon.net
Sat Jul 17 19:52:38 MDT 2021
put it third or fourth to get some speed (IE: pressure built up) to that
output shaft spinning the eccentric pump lobe.
A 200-300 rpm is barely enough to maintain proper pressure.
ptegler
On 7/17/2021 3:44 PM, Art McEwen wrote:
> Hi Bob, solenoid itself is operating fine but o/d is not engaging
> (running in 2nd gear on jacks). Pretty sure it’s not the adjustment
> as I’ve lined it up with the hole on the far side (and a little either
> side). Won’t engage when operated by hand either.
>
>> On Jul 17, 2021, at 3:35 PM, Kinderlehrer <kinderlehrer at comcast.net>
>> wrote:
>>
>>
>>
>> Before you do anything else, do a load test on the battery. Even if
>> it is producing 12 volts it may not be producing the 20 amps needed
>> to engage the OD.
>>
>> Bob
>>
>> *From:*Triumphs [mailto:triumphs-bounces at autox.team.net] *On Behalf
>> Of *Art McEwen
>> *Sent:* Saturday, July 17, 2021 11:24 AM
>> *To:* DAVID MASSEY
>> *Cc:* triumphs at autox.team.net
>> *Subject:* Re: [TR] TR3 O/D Solenoid plate
>>
>> Nothing went sproing when I took the plate off and I think I’ve got
>> the leak sealed but no amount of solenoid adjustment will engage the
>> overdrive. :(. The springs weren’t removed and I presume they’re
>> still seated where they were.
>>
>> I’m wondering if some of the sludge in the bottom of the case that I
>> tried to remove got relocated to a valve body somewhere. Thinking of
>> taking it for a road test then changing fluid again.
>>
>>
>>
>> On Jul 15, 2021, at 1:54 PM, Art McEwen <artwmcewen at gmail.com
>> <mailto:artwmcewen at gmail.com>> wrote:
>>
>>
>>
>> Thanks!
>>
>> Art
>>
>> On Thu, Jul 15, 2021, 11:25 AM DAVID MASSEY <dave1massey at cscom
>> <mailto:dave1massey at cs.com>> wrote:
>>
>> Nothing will go sproing but you will likely loose your
>> solenoid adjustment. Not a big deal as adjusting is pretty
>> simple.
>>
>> Dave
>>
>> -----Original Message-----
>> From: Art McEwen <artwmcewen at gmail.com
>> <mailto:artwmcewen at gmail.com>>
>> To: triumphs at autox.team.net <mailto:triumphs at autox.team.net>
>> Sent: Thu, Jul 15, 2021 9:48 am
>> Subject: [TR] TR3 O/D Solenoid plate
>>
>> It's weeping oil (even more than "acceptable"), can I loosen
>> the 4 screws to add gasket goop without misaligning the
>> plunger/spring thingy behind it or is it safe to remove
>> entirely while in place without something going "sprong"?
>>
>> Thanks,
>>
>> Art
>>
>> TS64???LO
>>
>> ** triumphs at autox.team.net <mailto:triumphs at autox.team.net> **
>>
>> Donate: http://www.team.net/donate.html
>> <http://www.team.net/donate.html>
>> Archive: http://www.team.net/pipermail/triumphs
>> <http://www.team.net/pipermail/triumphs>http://www.team.net/archive
>> <http://www.team.net/archive>
>>
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/triumphs/dave1massey@cs.com
>> <http://autox.team.net/mailman/options/triumphs/dave1massey@cs.com>
>>
>
> ** triumphs at autox.team.net **
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/triumphs http://www.team.net/archive
>
> Unsubscribe/Manage: http://autox.team.net/mailman/options/triumphs/ptegler@verizon.net
--
Paul Tegler
ptegler at verizon.net www.teglerizer.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/triumphs/attachments/20210717/3b23214e/attachment.htm>
More information about the Triumphs
mailing list