[TR] New Head Gasket Question

Dave dlhogye at comcast.net
Wed Jul 22 11:57:09 MDT 2020


You might consider checking with Gasketworks (www.headgasket.com). Mordy can make solid copper gaskets in many different thicknesses. 
Dave H.

Sent from my iPad

> On Jul 22, 2020, at 8:48 AM, <jpaynepbr at cox.net> <jpaynepbr at cox.net> wrote:
> 
> I'm going to be installing a Judson Supercharger on my TR3 this fall.  I have acquired the rebuilt supercharger, manifold, carb and a specially built dizzy.
> 
> I'll need some sort of thicker head gasket to lower the compression from its current 9.3/1 to a more suitable 8.7 (ish)/1   Anybody have any idea where to get it and what to use for the thicker head gasket?
> 
> 
> -----Original Message-----
> From: Triumphs <triumphs-bounces at autox.team.net> On Behalf Of bill beecher
> Sent: Tuesday, July 21, 2020 6:45 PM
> To: Jerry Van Vlack <jerryvv at roadrunner.com>
> Cc: triumphs at autox.team.net
> Subject: Re: [TR] Copper head gasket: Which side up?
> 
> My bad, that part number is for a lower end set from BPNW. 
> Bill
> 
> #dontkillgrandma
> 
> On Jul 21, 2020, at 6:49 PM, bill beecher <notakitcar at yahoo.com> wrote:
> 
> Thank you all, smooth side up it is.  
> Gasket and 87mm pistons and liners all came from TRF, Lucas p/n EC510L.   Head and deck are stock. 
> 
> Tony, yes the edge on the water holes are rolled, so I’ll leave them alone. 
> 
> Cheers,
> Bill B
> 
> 
> #dontkillgrandma
> 
> On Jul 21, 2020, at 6:30 PM, Jerry Van Vlack <jerryvv at roadrunner.com> wrote:
> 
> Adding to what Tony says, the gasket should NOT protrude into the bore.
> 
> Questions:
> What is the bore? 86, 87 or 89 mm?
> Where did the gasket come from and what brand is it? What is it's Part Number?
> How much is milled off the head?
> 
> I've been through this and the only thing working for me is to find an original AE 330 copper gasket. NOT the Repro 330 gasket. The originals are getting hard to find.
> 
> And be certain to re-torque the head.
> 
> With .070 milled off the head and 87mm liners and an original AE 330 HG I'm able to keep the gasket out of the combustion chamber.
> 
> Your results may differ.
> 
> JVV
> 
> -----Original Message----- From: Tony Drews
> Sent: Tuesday, July 21, 2020 6:05 PM
> To: triumphs at autox.team.net
> Subject: Re: [TR] Copper head gasket: Which side up?
> 
> Smooth side goes up.
> 
> It's better if the gasket doesn't protrude, hard to do if the head has been milled at all.
> 
> I've not messed with the water holes, no firm answer on that one.  If the edge of those is rolled over I'd leave alone, if it exposes the composite part of the gasket it's OK to open up a bit.
> 
>> On 7/21/2020 4:57 PM, bill beecher wrote:
>> Reassembling the TR3 motor for the old Morgan and I am dry fitting the head gasket. Two questions:
>> 1. Which side goes up, smooth or the rolled over side?
>> 2. On a couple cylinders the gasket protrudes into the bore by about 1mm, is this OK?
>> 3. At the front the holes in the gasket do not match exactly with the 
>> water passage, is it OK to open those up just a bit?  (The back aligns 
>> perfectly)
>> 
>> Thanks,
>> Bill B
>> TS74313E
>> 
>> #dontkillgrandma
>> ** triumphs at autox.team.net **
>> 
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/pipermail/triumphs 
>> http://www.team.net/archive
>> 
>> Unsubscribe/Manage: 
>> http://autox.team.net/mailman/options/triumphs/tony@tonydrews.com
> ** triumphs at autox.team.net **
> 
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/triumphs  http://www.team.net/archive
> 
> Unsubscribe/Manage: http://autox.team.net/mailman/options/triumphs/jerryvv@roadrunner.com
> ** triumphs at autox.team.net **
> 
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/triumphs  http://www.team.net/archive
> 
> Unsubscribe/Manage: http://autox.team.net/mailman/options/triumphs/notakitcar@yahoo.com
> 
> ** triumphs at autox.team.net **
> 
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/triumphs  http://www.team.net/archive
> 
> Unsubscribe/Manage: http://autox.team.net/mailman/options/triumphs/jpaynepbr@cox.net
> 
> ** triumphs at autox.team.net **
> 
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/triumphs  http://www.team.net/archive
> 
> Unsubscribe/Manage: http://autox.team.net/mailman/options/triumphs/dlhogye@comcast.net



More information about the Triumphs mailing list