[TR] Wire Wheels

Rochlin Robert rrochlin at comcast.net
Fri Apr 14 06:07:18 MDT 2017


	Thanks  to everyone for the great suggestions. 
	I did have the wheels check for trueness and wobble at a dedicated wire wheel shop before I had the balancing done. The wheels all came in within specs.  What I din’t mention in my first post is that when I had the troublesome wheel balanced I had them put clip on weights on the inside and outside rim instead of stick on weights on the middle of rim. Some people feel that you get a better dynamic balance that way.  I do think that this off season I will take the advice of sealing the wheels and eliminating the tubes.
	Take care.
	Bob
	72' TR6
> On Apr 13, 2017, at 10:33 AM, dave n <dave at ranteer.com> wrote:
> 
> you can buy tubes; if you need me to I will look up where I got mine.  you really need to go to a shop that does wire wheels if you want to do anything with wires.  most wheel/tire shops won't touch them.  and you should be glad for that in that they haven't a clue how to do it.  I have been told motorcycle shops are good; I actually found a place here in Dallas that does wires.
> 
> -----Original Message----- From: Rochlin Robert
> Sent: Wednesday, April 12, 2017 4:02 PM
> To: Triumphs List
> Subject: [TR] Wire Wheels
> 
> I’ve had wire wheels on my TR6 for about 14 years now.  I decided that since the tires were old and there was a slight vibration I’d replace the tires, get the wires tuned.  Fires lesson, Even though the wires required no tuning setting them up and checking specs was expensive.  If they had needed any adjustment it would have been more cost effective to just replace the wheels.
> I had a pronounced shake in the body when I got everything back together. This spring, by moving around the wheels I isolated the wheel that was causing the vibration, or at least most of it.  I went to a local well respected tire shop near my house to get the tire Road Force Balanced and was informed of  the following:
> -They don’t recommend tubes.
> -They can’t get tubes.
> -Their company policy is to not install tubes or deal with tube type tires.
> They did attempt to road force balance the tire the best they could moving the tire on the rim(but not touching the radioactive tube). They told me that the “Road Force” number was high, 23 lbs (Normal is between 0 and25) but they couldn’t tell me, so I understood it, what that number represented. They also told me that they thought the problem of the imbalance was caused by the tubes. (Of course the tubes were never problem in the past) They really did try to do a good job and the initial ride was better than before the balancing, but none of the technicians there had and experience with tube type tires.
> I’ve seen the tubeless Dayton wire wheels and the way they seal the tubes is with a coating of silicone adhesive around the inside rim to seal the wire nipples. Has anyone on the list tried to do this with older tube type wheels? When I had my wires specd I saw a tech at the wheel repair shop doing it to an old set of Dayton wire wheels, but given the difficulty and hourly rate I estimate that the owner could have replaced the wheels and had money left over for new tires.  In fairness, most of the shops work was from museums and old classic owners who wanted to preserve historically significant irreplaceable wheels.
> The Road Force balancing was $20.00 per tire, which I though was really reasonable.
> Take care.
> Bob Rochlin
> 72 TR6
> 
> ** triumphs at autox.team.net **
> 
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage: http://autox.team.net/mailman/options/triumphs/dave@ranteer.com 



More information about the Triumphs mailing list