<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=Windows-1252">
</head>
<body>
<div style="font-family: Aptos, -apple-system, HelveticaNeue, sans-serif;font-size: 12pt">
<div style="font-family: Aptos, Aptos_MSFontService, -apple-system, Roboto, Arial, Helvetica, sans-serif; font-size: 12pt;" dir="ltr">
Try bleeding the air out through the temp sender. Sometimes when we use adapters etc it raises the sender enough that it is in an air pocket. I always bleed the air out through the sender after I have driven the car a little. </div>
<div style="font-family: Aptos, Aptos_MSFontService, -apple-system, Roboto, Arial, Helvetica, sans-serif; font-size: 12pt;" dir="ltr">
<br>
</div>
<div style="font-family: Aptos, Aptos_MSFontService, -apple-system, Roboto, Arial, Helvetica, sans-serif; font-size: 12pt;" dir="ltr">
Good luck</div>
<div style="font-family: Aptos, Aptos_MSFontService, -apple-system, Roboto, Arial, Helvetica, sans-serif; font-size: 12pt;" dir="ltr">
Lynn</div>
</div>
<div id="ms-outlook-mobile-body-separator-line" style="font-family: Aptos, -apple-system, HelveticaNeue, sans-serif;font-size: 12pt" dir="auto">
<br>
</div>
<div id="ms-outlook-mobile-signature" style="font-family: Aptos, -apple-system, HelveticaNeue, sans-serif;font-size: 12pt">
Get <a href="https://aka.ms/o0ukef">Outlook for iOS</a></div>
<hr style="display:inline-block;width:98%" tabindex="-1">
<div id="divRplyFwdMsg" dir="ltr"><font face="Calibri, sans-serif" style="font-size:11pt" color="#000000"><b>From:</b> Tigers <tigers-bounces@autox.team.net> on behalf of gharlowe--- via Tigers <tigers@autox.team.net><br>
<b>Sent:</b> Thursday, August 21, 2025 3:21:53 PM<br>
<b>To:</b> tigers@autox.team.net <tigers@autox.team.net><br>
<b>Subject:</b> [Tigers] Temp Gauge Reading High</font>
<div> </div>
</div>
<style>
<!--
@font-face
{font-family:"Cambria Math"}
@font-face
{font-family:Calibri}
p.x_MsoNormal, li.x_MsoNormal, div.x_MsoNormal
{margin:0in;
font-size:12.0pt;
font-family:"Calibri",sans-serif}
span.x_EmailStyle17
{font-family:"Calibri",sans-serif;
color:windowtext}
.x_MsoChpDefault
{}
@page WordSection1
{margin:1.0in 1.0in 1.0in 1.0in}
div.x_WordSection1
{}
-->
</style>
<div lang="EN-US" link="#0563C1" vlink="#954F72" style="word-wrap:break-word">
<div class="x_WordSection1">
<p class="x_MsoNormal"><span style="font-size:11.0pt"> </span></p>
<p class="x_MsoNormal"><span style="font-size:11.0pt">Hey all –</span></p>
<p class="x_MsoNormal"><span style="font-size:11.0pt"> </span></p>
<p class="x_MsoNormal"><span style="font-size:11.0pt">It’s been quiet here so hoping to T-up an easy discussion.
</span></p>
<p class="x_MsoNormal"><span style="font-size:11.0pt"> </span></p>
<p class="x_MsoNormal"><span style="font-size:11.0pt">My temp gauge is reading about 25 degrees high. I noticed it after a shop installed a new clutch, which required the engine to be removed, coolant drained, etc., but nothing that should have affected how
the gauge reads. Running on a cool day, temps were reading around 215-220 degrees. To ensure I wasn’t actually in danger of overheating, I checked various water-cooled locations with an infrared thermometer. Highest reading was right at the water neck/thermostat
housing (191 deg F). The fuel gauge is reading accurately. I understand the under-dash instrument stabilizer can affect both instruments, but in this case, only one gauge is off. I plan to check the ground to the temp gauge and clean contact points at
the engine sending unit and at the gauge. Any other suggestions? </span></p>
<p class="x_MsoNormal"><span style="font-size:11.0pt"> </span></p>
<p class="x_MsoNormal"><span style="font-size:11.0pt">Thanks and I hope all is well out there!</span></p>
<p class="x_MsoNormal"><span style="font-size:11.0pt"> </span></p>
<p class="x_MsoNormal"><span style="font-size:11.0pt">Graham Harlowe</span></p>
<p class="x_MsoNormal"><span style="font-size:11.0pt">B382001466</span></p>
</div>
</div>
</body>
</html>