<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:m="http://schemas.microsoft.com/office/2004/12/omml" xmlns="http://www.w3.org/TR/REC-html40"><head><meta http-equiv=Content-Type content="text/html; charset=us-ascii"><meta name=Generator content="Microsoft Word 14 (filtered medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri","sans-serif";}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:purple;
text-decoration:underline;}
span.EmailStyle17
{mso-style-type:personal-compose;
font-family:"Arial","sans-serif";
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-family:"Calibri","sans-serif";}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext="edit" spidmax="1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext="edit">
<o:idmap v:ext="edit" data="1" />
</o:shapelayout></xml><![endif]--></head><body lang=EN-US link=blue vlink=purple><div class=WordSection1><p class=MsoNormal><span style='font-size:16.0pt;font-family:"Arial","sans-serif"'>Seems as though my original post disappeared into lala land! The post was about what I did to cure the issue concerning the early headlight bezels popping off at the most inappropriate time - like mine did some years ago! Some time ago, there was a discussion about drilling a hole in an original Tiger part- a big No No in my opinion! So here is what I did. I took a length of fishing line (very strong 65 lb. test) and fed it through the small loop (roll) in the headlight bezel (the part that snaps onto the part that is fastened to the fender). I then tied a knot and left several inches of line (6-8inches each side should be enough). It wouldn’t hurt to put a drop of Super glue on the knot. Now carefully, with the bezel in place with a small gap at the bottom, tie the two ends around the piece that is attached to the fender. It’s tight - the more nimble your fingers are the better. The distance is about an inch or so - the closer the better. Then tie a good knot and then some Super Glue to keep the knot from unraveling (actually I used Bondic). Now if the Bezel pops out it can’t come all the way off. A word about the fishing line - it’s actually braided and extremely strong. I bought it at Walmart some time ago. I’ve found many uses for it. I’m enclosing a picture of the fish line package. Also a picture of the installed line. It was very hard to get a close enough picture - o it’s kind of upside down.<o:p></o:p></span></p><p class=MsoNormal><span style='font-size:16.0pt;font-family:"Arial","sans-serif"'><o:p> </o:p></span></p><p class=MsoNormal><span style='font-size:16.0pt;font-family:"Arial","sans-serif"'>Jerry Christopherson<o:p></o:p></span></p><p class=MsoNormal><span style='font-size:16.0pt;font-family:"Arial","sans-serif"'>TAC Insp. #58<o:p></o:p></span></p><p class=MsoNormal><span style='font-size:16.0pt;font-family:"Arial","sans-serif"'><o:p> </o:p></span></p><p class=MsoNormal><span style='font-size:16.0pt;font-family:"Arial","sans-serif"'><o:p> </o:p></span></p><p class=MsoNormal><span style='font-size:14.0pt;font-family:"Arial","sans-serif"'><o:p> </o:p></span></p><p class=MsoNormal><span style='font-size:14.0pt;font-family:"Arial","sans-serif"'><o:p> </o:p></span></p><p class=MsoNormal><span style='font-size:14.0pt;font-family:"Arial","sans-serif"'><o:p> </o:p></span></p></div></body></html>