<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:m="http://schemas.microsoft.com/office/2004/12/omml" xmlns="http://www.w3.org/TR/REC-html40"><head><meta http-equiv=Content-Type content="text/html; charset=us-ascii"><meta name=Generator content="Microsoft Word 15 (filtered medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
span.EmailStyle17
{mso-style-type:personal-compose;
font-family:"Calibri",sans-serif;
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-family:"Calibri",sans-serif;}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext="edit" spidmax="1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext="edit">
<o:idmap v:ext="edit" data="1" />
</o:shapelayout></xml><![endif]--></head><body lang=EN-US link="#0563C1" vlink="#954F72"><div class=WordSection1><p class=MsoNormal><b>Under tray wood</b> – the offset of the body mount holes on my Tiger is 3/16”<o:p></o:p></p><p class=MsoNormal>I made a cardboard templet per the drawing – pic #1 – the offset angle is acceptable to me<o:p></o:p></p><p class=MsoNormal><o:p> </o:p></p><p class=MsoNormal>Pic #2 – battery tray over the templet – in my opinion this sticks out too far and at the front area it is tight to the body<o:p></o:p></p><p class=MsoNormal>I will make and install this piece before I make a judgement call on its length – this is not a concours Tiger<o:p></o:p></p><p class=MsoNormal><o:p> </o:p></p><p class=MsoNormal><b>Side wood</b> – I made a piece per the drawing and I found that my body mount holes are about a 1/16” closer together – I opened the through holes to make this piece fit better I made a 2<sup>nd</sup> piece with the mount holes closer and a better fit<o:p></o:p></p><p class=MsoNormal><o:p> </o:p></p><p class=MsoNormal>I do suggest that anyone making this piece – check the body mount hole distance carefully and make any needed correction.<o:p></o:p></p><p class=MsoNormal>You can make 1 mount hole, install with 1 screw and mark exactly where the 2<sup>nd</sup> hole is located.<o:p></o:p></p><p class=MsoNormal><o:p> </o:p></p><p class=MsoNormal>Now to apply some wood preservative and let them dry – I’ll install these pieces later this month<o:p></o:p></p><p class=MsoNormal><o:p> </o:p></p><p class=MsoNormal>Ron Fraser<o:p></o:p></p><p class=MsoNormal><o:p> </o:p></p><p class=MsoNormal><o:p> </o:p></p></div></body></html>