<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body>
Hi Theo!<br>
Interesting. Steve Wickland has the McLeod in his Tiger. He has
been complaining about it for some time, I forget but I think his is
causing<br>
the clutch to slip. Tom Hall recommended to use hard line and
fittings because the McLeod swivel ones leak (IIRC).<br>
Gary<br>
<br>
<br>
<div class="moz-cite-prefix">On 5/28/2021 7:55 PM, Theo Smit wrote:<br>
</div>
<blockquote type="cite"
cite="mid:1837200278.85212686.1622256903666.JavaMail.zimbra@cds218.dcs.int.inet">
<meta http-equiv="content-type" content="text/html; charset=UTF-8">
<div dir="ltr">I ended up making an anti-rotation bracket that
located the McLeod throwout bearing and kept it from pulling on
the swivel fittings. Without that, the fittings would leak a bit
of fluid every time you applied the clutch with the engine
running. </div>
<div dir="ltr">Theo</div>
<div dir="ltr"><br>
<blockquote type="cite">On May 28, 2021, at 8:25 PM, Michael
Wood via Tigers <a class="moz-txt-link-rfc2396E" href="mailto:tigers@autox.team.net"><tigers@autox.team.net></a> wrote:<br>
<br>
</blockquote>
</div>
<blockquote type="cite">
<div dir="ltr">
<div
style="font-size:10pt;font-family:arial,helvetica,sans-serif;color:black;">
<div
style="font-family:arial,helvetica,sans-serif;font-size:10pt;color:black;">Gary,
the McLeod in "Blue" (Tom's med blue car) is still going
strong after 25 years, so I'm not sure why he bailed. I
think it is mostly because he's had no complaints about
the Tilton and likes doing the conversion using their 7/8"
master. </div>
<div
style="font-family:arial,helvetica,sans-serif;font-size:10pt;color:black;"><br>
</div>
<div
style="font-family:arial,helvetica,sans-serif;font-size:10pt;color:black;"><br>
<br>
<br>
-----Original Message-----<br>
From: Gary <a class="moz-txt-link-rfc2396E" href="mailto:garywinblad@comcast.net"><garywinblad@comcast.net></a><br>
To: <a class="moz-txt-link-abbreviated" href="mailto:tigers@autox.team.net">tigers@autox.team.net</a><br>
Sent: Fri, May 28, 2021 6:50 pm<br>
Subject: Re: [Tigers] Clutch issue<br>
<br>
</div>
<div id="yiv8877381035">
<div> Thanks Mike,<br clear="none">
Ok, yeah he was recommending the McCleod with his mod to
the fittings...<br clear="none">
Paul Reisentz also told me that McCLeod themselves did
not recommend their part for use in Tigers!<br
clear="none">
<br clear="none">
Tilton.. or are there any more details on your
Australian job?<br clear="none">
Gary<br clear="none">
<br clear="none">
<div class="yiv8877381035yqt5127846552"
id="yiv8877381035yqt00869">
<div class="yiv8877381035moz-cite-prefix">On 5/28/2021
5:22 PM, Michael Wood via Tigers wrote:<br
clear="none">
</div>
<blockquote type="cite"> </blockquote>
</div>
</div>
<div class="yiv8877381035yqt5127846552"
id="yiv8877381035yqt56906">
<div>
<div style="font-size:10pt;font-family:arial,
helvetica, sans-serif;color:black;">
<div style="font-family:arial, helvetica,
sans-serif;font-size:10pt;color:black;">I just
talked to Tom. He's still using and recommending
use of a hydraulic/annular TO bearing. But, he
won't use the McLeod piece, only Tilton, these
days. </div>
<div style="font-family:arial, helvetica,
sans-serif;font-size:10pt;color:black;"><br
clear="none">
</div>
<div style="font-family:arial, helvetica,
sans-serif;font-size:10pt;color:black;">Mike<br
clear="none">
<br clear="none">
-----Original Message-----<br clear="none">
From: Jerry Christopherson <a rel="nofollow
noopener noreferrer" shape="rect"
class="yiv8877381035moz-txt-link-rfc2396E"
ymailto="mailto:JCMC2006@suddenlink.net"
target="_blank"
href="mailto:JCMC2006@suddenlink.net"
moz-do-not-send="true"><JCMC2006@suddenlink.net></a><br
clear="none">
To: Tiger Autox <a rel="nofollow noopener
noreferrer" shape="rect"
class="yiv8877381035moz-txt-link-rfc2396E"
ymailto="mailto:TIGERS@AUTOX.TEAM.NET"
target="_blank"
href="mailto:TIGERS@AUTOX.TEAM.NET"
moz-do-not-send="true"><TIGERS@AUTOX.TEAM.NET></a><br
clear="none">
Sent: Fri, May 28, 2021 2:50 pm<br clear="none">
Subject: [Tigers] Clutch issue<br clear="none">
<br clear="none">
</div>
<div id="yiv8877381035">
<style>#yiv8877381035
filtered {}#yiv8877381035
p.yiv8877381035MsoNormal, #yiv8877381035 li.yiv8877381035MsoNormal, #yiv8877381035 div.yiv8877381035MsoNormal
{margin:0in;margin-bottom:.0001pt;font-size:11.0pt;}#yiv8877381035 a:link, #yiv8877381035 span.yiv8877381035MsoHyperlink
{color:blue;text-decoration:underline;}#yiv8877381035 a:visited, #yiv8877381035 span.yiv8877381035MsoHyperlinkFollowed
{color:purple;text-decoration:underline;}#yiv8877381035 span.yiv8877381035EmailStyle17
{color:windowtext;}#yiv8877381035 .yiv8877381035MsoChpDefault
{}#yiv8877381035 filtered {}#yiv8877381035 div.yiv8877381035WordSection1
{}</style>
<div>
<div class="yiv8877381035WordSection1">
<p class="yiv8877381035MsoNormal"><span
style="font-size:14.0pt;font-family:'Arial',
'sans-serif';">Well, I did some measuring
today (by the way the new clutch and
cylinder kits didn’t solve my problem) and
thought I would pass on info for anybody
that is interested.</span></p>
<p class="yiv8877381035MsoNormal"><span
style="font-size:14.0pt;font-family:'Arial',
'sans-serif';">The actual amount of
movement of the slave cylinder with a full
to the floor movement of the clutch peddle
is .745”. The measure of the piston
movement from the very back to when the
piston comes to the very front of the
cylinder (not protruding) is like I
mentioned before is 1.35”, so that leaves
approximately .605” more potential
movement to apply to the clutch arm. I’m
hoping the .700 Girling master cylinder I
just ordered will take up just that
amount. I can only hope. HA! If not I’ll
pull the engine and tranny again and get a
CF clutch. As for a annular TO bearing,
my friend has a highly modified Mazda with
a 331 Ford engine for road racing with a
annular TO bearing and it works very well
with the stock master cylinder. I would be
very interested in why TH doesn’t like
them anymore.</span></p>
<p class="yiv8877381035MsoNormal"><span
style="font-size:14.0pt;font-family:'Arial',
'sans-serif';">Jerry </span></p>
<p class="yiv8877381035MsoNormal"><span
style="font-size:14.0pt;font-family:'Arial',
'sans-serif';"> </span></p>
</div>
</div>
</div>
_______________________________________________<br
clear="none">
<br clear="none">
<a rel="nofollow noopener noreferrer" shape="rect"
ymailto="mailto:tigers@autox.team.net"
target="_blank"
href="mailto:tigers@autox.team.net"
moz-do-not-send="true">tigers@autox.team.net</a><br
clear="none">
<br clear="none">
Donate: <a rel="nofollow noopener noreferrer"
shape="rect" target="_blank"
href="http://www.team.net/donate.html"
moz-do-not-send="true">http://www.team.net/donate.html</a><br
clear="none">
Archive: <a rel="nofollow noopener noreferrer"
shape="rect" target="_blank"
href="http://www.team.net/pipermail/tigers"
moz-do-not-send="true">http://www.team.net/pipermail/tigers
</a><a rel="nofollow noopener noreferrer"
shape="rect" target="_blank"
href="http://autox.team.net/archive"
moz-do-not-send="true">http://autox.team.net/archive</a><br
clear="none">
<br clear="none">
Unsubscribe: <a rel="nofollow noopener noreferrer"
shape="rect" target="_blank"
href="http://autox.team.net/mailman/options/tigers/mwood24020@aol.com"
moz-do-not-send="true">http://autox.team.net/mailman/options/tigers/mwood24020@aol.com</a><br
clear="none">
<br clear="none">
<br clear="none">
</div>
<br clear="none">
<fieldset class="yiv8877381035mimeAttachmentHeader"></fieldset>
<pre class="yiv8877381035moz-quote-pre">_______________________________________________
<a rel="nofollow noopener noreferrer" shape="rect" class="yiv8877381035moz-txt-link-abbreviated" ymailto="mailto:tigers@autox.team.net" target="_blank" href="mailto:tigers@autox.team.net" moz-do-not-send="true">tigers@autox.team.net</a>
Donate: <a rel="nofollow noopener noreferrer" shape="rect" class="yiv8877381035moz-txt-link-freetext" target="_blank" href="http://www.team.net/donate.html" moz-do-not-send="true">http://www.team.net/donate.html</a>
Archive: <a rel="nofollow noopener noreferrer" shape="rect" class="yiv8877381035moz-txt-link-freetext" target="_blank" href="http://www.team.net/pipermail/tigers" moz-do-not-send="true">http://www.team.net/pipermail/tigers</a> <a rel="nofollow noopener noreferrer" shape="rect" class="yiv8877381035moz-txt-link-freetext" target="_blank" href="http://autox.team.net/archive" moz-do-not-send="true">http://autox.team.net/archive</a>
Unsubscribe: <a rel="nofollow noopener noreferrer" shape="rect" class="yiv8877381035moz-txt-link-freetext" target="_blank" href="http://autox.team.net/mailman/options/tigers/garywinblad@comcast.net" moz-do-not-send="true">http://autox.team.net/mailman/options/tigers/garywinblad@comcast.net</a>
</pre>
<br clear="none">
</div>
</div>
</div>
<div class="yqt5127846552" id="yqt49742">_______________________________________________<br
clear="none">
<br clear="none">
<a shape="rect" ymailto="mailto:tigers@autox.team.net"
href="mailto:tigers@autox.team.net"
moz-do-not-send="true">tigers@autox.team.net</a><br
clear="none">
<br clear="none">
Donate: <a shape="rect"
href="http://www.team.net/donate.html" target="_blank"
moz-do-not-send="true">http://www.team.net/donate.html</a><br
clear="none">
Archive: <a shape="rect"
href="http://www.team.net/pipermail/tigers"
target="_blank" moz-do-not-send="true">http://www.team.net/pipermail/tigers
</a><a shape="rect" href="http://autox.team.net/archive"
target="_blank" moz-do-not-send="true">http://autox.team.net/archive</a><br
clear="none">
<br clear="none">
Unsubscribe: <a shape="rect"
href="http://autox.team.net/mailman/options/tigers/mwood24020@aol.com"
target="_blank" moz-do-not-send="true">http://autox.team.net/mailman/options/tigers/mwood24020@aol.com</a><br
clear="none">
<br clear="none">
<br clear="none">
</div>
</div>
</div>
</blockquote>
</blockquote>
<br>
</body>
</html>