<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body>
Uh, I think some of that is wrong info.. very confusing to me
anyway.<br>
<br>
Leave the loop in the stock white wire(or straighten it out) but do
NOT hook it back to the new tach.<br>
That wire goes directly from the ignition switch to the top of the
ballast resistor, needs NO connection<br>
to your new tach.<br>
<br>
Your new white wire with spade needs an extension wire going to the
low (negative) side of the<br>
coil where the wire goes to the points (Pertronix).<br>
<br>
The +12 green wire needs to plug to the original spade on the back
of the tach.<br>
HTH,<br>
Gary W.<br>
<br>
<br>
<div class="moz-cite-prefix">On 11/21/2019 7:09 AM, Donald Antilla
wrote:<br>
</div>
<blockquote type="cite"
cite="mid:0AC14875-9C89-45E9-80A0-3525DB2F9D98@sbcglobal.net">
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
<meta name="Generator" content="Microsoft Word 15 (filtered
medium)">
<!--[if !mso]><style>v\:* {behavior:url(#default#VML);}
o\:* {behavior:url(#default#VML);}
w\:* {behavior:url(#default#VML);}
.shape {behavior:url(#default#VML);}
</style><![endif]-->
<style><!--
/* Font Definitions */
@font-face
{font-family:Wingdings;
panose-1:5 0 0 0 0 0 0 0 0 0;}
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
@font-face
{font-family:"Times New Roman \(Body CS\)";
panose-1:2 11 6 4 2 2 2 2 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:purple;
text-decoration:underline;}
p.MsoListParagraph, li.MsoListParagraph, div.MsoListParagraph
{mso-style-priority:34;
margin-top:0in;
margin-right:0in;
margin-bottom:0in;
margin-left:.5in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
p.msonormal0, li.msonormal0, div.msonormal0
{mso-style-name:msonormal;
mso-margin-top-alt:auto;
margin-right:0in;
mso-margin-bottom-alt:auto;
margin-left:0in;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
span.EmailStyle18
{mso-style-type:personal-reply;
font-family:"Arial",sans-serif;
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-size:10.0pt;}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
/* List Definitions */
@list l0
{mso-list-id:1293826678;
mso-list-type:hybrid;
mso-list-template-ids:73332182 67698689 67698691 67698693 67698689 67698691 67698693 67698689 67698691 67698693;}
@list l0:level1
{mso-level-number-format:bullet;
mso-level-text:;
mso-level-tab-stop:none;
mso-level-number-position:left;
text-indent:-.25in;
font-family:Symbol;}
@list l0:level2
{mso-level-number-format:bullet;
mso-level-text:o;
mso-level-tab-stop:none;
mso-level-number-position:left;
text-indent:-.25in;
font-family:"Courier New";}
@list l0:level3
{mso-level-number-format:bullet;
mso-level-text:;
mso-level-tab-stop:none;
mso-level-number-position:left;
text-indent:-.25in;
font-family:Wingdings;}
@list l0:level4
{mso-level-number-format:bullet;
mso-level-text:;
mso-level-tab-stop:none;
mso-level-number-position:left;
text-indent:-.25in;
font-family:Symbol;}
@list l0:level5
{mso-level-number-format:bullet;
mso-level-text:o;
mso-level-tab-stop:none;
mso-level-number-position:left;
text-indent:-.25in;
font-family:"Courier New";}
@list l0:level6
{mso-level-number-format:bullet;
mso-level-text:;
mso-level-tab-stop:none;
mso-level-number-position:left;
text-indent:-.25in;
font-family:Wingdings;}
@list l0:level7
{mso-level-number-format:bullet;
mso-level-text:;
mso-level-tab-stop:none;
mso-level-number-position:left;
text-indent:-.25in;
font-family:Symbol;}
@list l0:level8
{mso-level-number-format:bullet;
mso-level-text:o;
mso-level-tab-stop:none;
mso-level-number-position:left;
text-indent:-.25in;
font-family:"Courier New";}
@list l0:level9
{mso-level-number-format:bullet;
mso-level-text:;
mso-level-tab-stop:none;
mso-level-number-position:left;
text-indent:-.25in;
font-family:Wingdings;}
ol
{margin-bottom:0in;}
ul
{margin-bottom:0in;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext="edit" spidmax="1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext="edit">
<o:idmap v:ext="edit" data="1" />
</o:shapelayout></xml><![endif]-->
<div class="WordSection1">
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">Gary
and Friends:<o:p></o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">
I just had a good discussion with Peter Bayer who owns
Nisonger Corporation and who modifies the tachs.<o:p></o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">Peter
explained the entire circuitry to me and I will only
summarize in words, then please view the attached file from
Nisonger.<o:p></o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">The
summary is:<o:p></o:p></span></p>
<ul style="margin-top:0in" type="disc">
<li class="MsoListParagraph"
style="margin-left:0in;mso-list:l0 level1 lfo1"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">Keep
the loop on the back of the tach intact. Do NOT remove nor
disconnect. This SHOULD therefore provide 12 volt power to
the ballast resistor<o:p></o:p></span></li>
<li class="MsoListParagraph"
style="margin-left:0in;mso-list:l0 level1 lfo1"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">Route
a wire from the female spade terminal at back of the
updated tach TO the negative side of the ignition coil
which has been equipped with the Pertronix system.<o:p></o:p></span></li>
</ul>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif"><o:p> </o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">I’ve
attached the instructions from Nisonger for you to follow.<o:p></o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif"><o:p> </o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">Peter
Bayer is a smart and helpful person and is quite willing to
receive a call from Gary and walk Gary through the
instructions.<o:p></o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">I
think once Gary talks with Peter while reading the attached
instructions that all will be good.<o:p></o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">Peter
Bayer’s number is (914) 381-3600<o:p></o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif">Please
let me know how it goes. <o:p></o:p></span></p>
<p class="MsoListParagraph"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif"><o:p> </o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif"><o:p> </o:p></span></p>
<div>
<p class="MsoNormal"><i><span style="font-size:14.0pt">Don
Antilla <o:p></o:p></span></i></p>
<p class="MsoNormal"><i><span style="font-size:14.0pt">Southbury,
CT<o:p></o:p></span></i></p>
<p class="MsoNormal"><i><span style="font-size:14.0pt">203-264-8301
Home<o:p></o:p></span></i></p>
<p class="MsoNormal"><i><span style="font-size:14.0pt">203-592-8427
Cell<o:p></o:p></span></i></p>
</div>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif"><o:p> </o:p></span></p>
<p class="MsoNormal"><span
style="font-size:16.0pt;font-family:"Arial",sans-serif"><o:p> </o:p></span></p>
<div style="border:none;border-top:solid #B5C4DF
1.0pt;padding:3.0pt 0in 0in 0in">
<p class="MsoNormal"><b><span
style="font-size:12.0pt;color:black">From: </span></b><span
style="font-size:12.0pt;color:black">Tigers
<a class="moz-txt-link-rfc2396E" href="mailto:tigers-bounces@autox.team.net"><tigers-bounces@autox.team.net></a> on behalf of Theo
Smit via Tigers <a class="moz-txt-link-rfc2396E" href="mailto:tigers@autox.team.net"><tigers@autox.team.net></a><br>
<b>Reply-To: </b>Theo Smit <a class="moz-txt-link-rfc2396E" href="mailto:tsmit@shaw.ca"><tsmit@shaw.ca></a><br>
<b>Date: </b>Wednesday, November 20, 2019 at 11:49 PM<br>
<b>To: </b>Gary <a class="moz-txt-link-rfc2396E" href="mailto:garywinblad@comcast.net"><garywinblad@comcast.net></a><br>
<b>Cc: </b>tigers <a class="moz-txt-link-rfc2396E" href="mailto:Tigers@autox.team.net"><Tigers@autox.team.net></a><br>
<b>Subject: </b>Re: [Tigers] Starter Solenoid<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><o:p> </o:p></p>
</div>
<div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">remember
that TigersUnited.com is not dead, and among other
resources it has a complete scan of the Tiger Workshop
Manual, including good re-digitized drawings of the
wiring diagram.<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black"><a
href="http://www.tigersunited.com/resources/wsm/tt-images/MKIBIGwiring.jpg"
moz-do-not-send="true">http://www.tigersunited.com/resources/wsm/tt-images/MKIBIGwiring.jpg</a><o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black"><o:p> </o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">So,
with respect to that drawing:<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">-
Your tach should be powered through the spade connector
on the back of the tach. That should be connected to a
green wire that is energized only when the ignition is
on or in the start position.<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">-
Your tach should be grounded through the black
daisy-chain wires that need to be connected to the dash
frame somewhere (not just gauge to gauge to gauge).<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">-
The OEM wiring has the coil power run through a white
wire, looped through the transformer U-shaped metal
piece and plastic frame that is mounted on the back of
the tach. It kind of sounds like the Nissonger rebuild
gave you an alternate means of sensing the ignition with
their white "signal in" line. You should have got a
wiring diagram with the tach, if they changed the way it
can be wired up.<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">-
That OEM white wire needs to connect to one end of the
ballast resistor as shown in the wiring diagram (and the
other end plugs into the ignition switch, not the tach).
It supplies power to the coil through the ballast
resistor when the car is running.<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">-
The white/blue wire runs from the solenoid to the
ballast resistor to the coil positive.<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black"><o:p> </o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">It
sounds like you need to make sure that the white wire
you plugged into the tach, is connected to the ballast
resistor at the other end. If so, unplug the tach end,
loop it through the transformer block, and plug it into
the #2 terminal on the ignition switch.<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black"><o:p> </o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">If
the tach works properly, then you're good. If it does
not, then try looping the white wire through the
transformer block in the opposite direction. If that
still fails (but the engine runs properly), then abandon
the transformer and use Nissonger's signal wire. As Gary
says, that wire should be connected using a new
extension wire to the coil negative terminal ( where the
points connect ).<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black"><o:p> </o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black"><o:p> </o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">Good
luck,<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">Theo<o:p></o:p></span></p>
</div>
<div class="MsoNormal" style="text-align:center"
align="center"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">
<hr width="100%" size="0" align="center"></span></div>
<div>
<p class="MsoNormal"><b><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">From:
</span></b><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">"tigers"
<a class="moz-txt-link-rfc2396E" href="mailto:tigers@autox.team.net"><tigers@autox.team.net></a><br>
<b>To: </b>"Joe Brown" <a class="moz-txt-link-rfc2396E" href="mailto:jbbrown1980@gmail.com"><jbbrown1980@gmail.com></a><br>
<b>Cc: </b>"tigers" <a class="moz-txt-link-rfc2396E" href="mailto:Tigers@autox.team.net"><Tigers@autox.team.net></a><br>
<b>Sent: </b>Wednesday, November 20, 2019 7:22:28 PM<br>
<b>Subject: </b>Re: [Tigers] Starter Solenoid<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black"><o:p> </o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">The
Signal wire should probably wire to<o:p></o:p></span></p>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">the
points or low side of the coil.<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">The
white wire should not end at the tach<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">but
would do a one loop through the coil<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">pickup
on the back of the stock tach and<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">then
run to the ballast.<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">You
do need 12v to the back of the tach<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">spade
terminal and a ground.<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal" style="margin-bottom:12.0pt"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">Gary<o:p></o:p></span></p>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">Sent
from my iPhone<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black"><o:p> </o:p></span></p>
<blockquote style="margin-top:5.0pt;margin-bottom:5.0pt">
<p class="MsoNormal" style="margin-bottom:12.0pt"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">On
Nov 20, 2019, at 2:30 PM, Joe Brown via Tigers
<a class="moz-txt-link-rfc2396E" href="mailto:tigers@autox.team.net"><tigers@autox.team.net></a> wrote:<o:p></o:p></span></p>
</blockquote>
</div>
<blockquote style="margin-top:5.0pt;margin-bottom:5.0pt">
<div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">Thanks
to Donald Antilla and Ron Fraser for their quick
replies. They have me on the right track now.
In my new wiring harness I have one white wire
that comes out of the harness behind the tach
and I assumed it plugged into the white wire
(labeled "signal in") on the back of the tach.
My tach was rebuilt by Nisonger and has the
updated electronics. I ohmed that wire out and
it is the one that goes to the ballast
resistor. So should I run a new wire from the
ignition switch to the tach and piggyback the
ballast wire to that? <o:p></o:p></span></p>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">Thanks,<o:p></o:p></span></p>
</div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">Joe
Brown<o:p></o:p></span></p>
</div>
</div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black"><o:p> </o:p></span></p>
<div>
<div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">On
Wed, Nov 20, 2019 at 3:31 PM Donald Antilla
<<a href="mailto:fast427@sbcglobal.net"
target="_blank" moz-do-not-send="true">fast427@sbcglobal.net</a>>
wrote:<o:p></o:p></span></p>
</div>
<blockquote style="border:none;border-left:solid
#CCCCCC 1.0pt;padding:0in 0in 0in
6.0pt;margin-left:4.8pt;margin-right:0in">
<p class="MsoNormal" style="margin-bottom:12.0pt"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">The
starter solenoid temporarily supplies 12 volts
to the. Oil while the starter is cranking. <br>
As soon as you release the key that temporary
12 volts is disconnected and the power to the
coil is via the ballast resistor. <br>
It sounds like you either have a bad ballast
resistor or broken wiring to the ballast
resistor. <br>
Temporarily add an alligator jumper across the
two tabs on the resistor and see if it starts.
If it does start you have a bad resistor. <br>
And if that does not work, start looking for
lack of 12 volts INTO. The ballast resistor. <br>
<br>
From Don's iPhone 203-592-8427<br>
Or 203-264-8301 home<br>
<br>
> On Nov 20, 2019, at 4:20 PM, Joe Brown
via Tigers <<a
href="mailto:tigers@autox.team.net"
target="_blank" moz-do-not-send="true">tigers@autox.team.net</a>>
wrote:<br>
> <br>
> <br>
> Hey,<br>
> <br>
> I'm trying to fire up my engine for the
first time and I have a question. When I turn
the key to the start position the engine turns
over and fires up. But as soon as I let go of
the key so that it returns to the run position
it dies. It seems like the ignition system is
only getting power when the key is in the
start position. <br>
> <br>
> I'm a little confused by the wiring
diagram. The white/blue wire from the
solenoid goes to the coil and this would seem
to imply that there should always be 12V on
this wire when the key is in the run
position. Is this correct? I'm only getting
the 12V on this line when the key is in the
start position. <br>
> <br>
> Any ideas?<br>
> <br>
> Thanks,<br>
> Joe Brown<br>
>
_______________________________________________<br>
> <br>
> <a href="mailto:tigers@autox.team.net"
target="_blank" moz-do-not-send="true">tigers@autox.team.net</a><br>
> <br>
> Donate: <a
href="http://www.team.net/donate.html"
target="_blank" moz-do-not-send="true">http://www.team.net/donate.html</a><br>
> Archive: <a
href="http://www.team.net/pipermail/tigers"
target="_blank" moz-do-not-send="true">http://www.team.net/pipermail/tigers</a>
<a href="http://autox.team.net/archive"
target="_blank" moz-do-not-send="true">http://autox.team.net/archive</a><br>
> <br>
> Unsubscribe: <a
href="http://autox.team.net/mailman/options/tigers/fast427@sbcglobal.net"
target="_blank" moz-do-not-send="true">http://autox.team.net/mailman/options/tigers/fast427@sbcglobal.net</a><br>
> <br>
> <o:p></o:p></span></p>
</blockquote>
</div>
<p class="MsoNormal" style="margin-bottom:12.0pt"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black">_______________________________________________<br>
<br>
<a class="moz-txt-link-abbreviated" href="mailto:tigers@autox.team.net">tigers@autox.team.net</a><br>
<br>
Donate: <a class="moz-txt-link-freetext" href="http://www.team.net/donate.html">http://www.team.net/donate.html</a><br>
Archive: <a class="moz-txt-link-freetext" href="http://www.team.net/pipermail/tigers">http://www.team.net/pipermail/tigers</a>
<a class="moz-txt-link-freetext" href="http://autox.team.net/archive">http://autox.team.net/archive</a><br>
<br>
Unsubscribe:
<a class="moz-txt-link-freetext" href="http://autox.team.net/mailman/options/tigers/garywinblad@comcast.net">http://autox.team.net/mailman/options/tigers/garywinblad@comcast.net</a><br>
<br>
<o:p></o:p></span></p>
</div>
</blockquote>
</div>
<p class="MsoNormal"><span
style="font-size:10.0pt;font-family:"Arial",sans-serif;color:black"><br>
_______________________________________________<br>
<br>
<a class="moz-txt-link-abbreviated" href="mailto:tigers@autox.team.net">tigers@autox.team.net</a><br>
<br>
Donate: <a class="moz-txt-link-freetext" href="http://www.team.net/donate.html">http://www.team.net/donate.html</a><br>
Archive: <a class="moz-txt-link-freetext" href="http://www.team.net/pipermail/tigers">http://www.team.net/pipermail/tigers</a>
<a class="moz-txt-link-freetext" href="http://autox.team.net/archive">http://autox.team.net/archive</a><br>
<br>
Unsubscribe:
<a class="moz-txt-link-freetext" href="http://autox.team.net/mailman/options/tigers/tsmit@shaw.ca">http://autox.team.net/mailman/options/tigers/tsmit@shaw.ca</a><o:p></o:p></span></p>
</div>
</div>
<p class="MsoNormal">_______________________________________________
<a class="moz-txt-link-abbreviated" href="mailto:tigers@autox.team.net">tigers@autox.team.net</a> Donate: <a class="moz-txt-link-freetext" href="http://www.team.net/donate.html">http://www.team.net/donate.html</a>
Archive: <a class="moz-txt-link-freetext" href="http://www.team.net/pipermail/tigers">http://www.team.net/pipermail/tigers</a>
<a class="moz-txt-link-freetext" href="http://autox.team.net/archive">http://autox.team.net/archive</a> Unsubscribe:
<a class="moz-txt-link-freetext" href="http://autox.team.net/mailman/options/tigers/fast427@sbcglobal.net">http://autox.team.net/mailman/options/tigers/fast427@sbcglobal.net</a>
<o:p></o:p></p>
</div>
</blockquote>
<br>
</body>
</html>