<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META content="text/html; charset=US-ASCII" http-equiv=Content-Type>
<META name=GENERATOR content="MSHTML 11.00.9600.18538"></HEAD>
<BODY id=role_body style="FONT-SIZE: 10pt; FONT-FAMILY: Arial; COLOR: #000000"
bottomMargin=7 leftMargin=7 rightMargin=7 topMargin=7><FONT id=role_document
color=#000000 size=2 face=Arial>
<DIV>OK thanks. I had planned to buy an M6 stainless steel Clevis jaw (?)
to replace the steel one on the steel rod. However, the M6 threaded Clevis
jaw also has an M6 hole and I need the hole for the linkage on the brake drum
handbrake to be 5/16 (about 8mm).</DIV>
<DIV> </DIV>
<DIV>So, it appears I either need to make a Clevis jaw or find someone else to
make me one or a combination of both.</DIV>
<DIV> </DIV>
<DIV>The problem with my making the part is that I don't have a pillar drill let
alone a lathe so drilling a hole centrally and straight into a 16mm piece of
square stainless steel bar so I can tap it M6 will be a challenge.
Likewise drilling a hole 5/16 for the clevis pin will also be a challenge.
Now that I have to make/get someone to make the Clevis jaw I regret going the
metric route which I went down because it enabled me to buy an off the shelf
clevis jaw - duhh.</DIV>
<DIV> </DIV>
<DIV>I might drop my local jobbing machine shop next Friday morning to see if I
can get the bar drilled as a quick and cheap cash job or failing that re-visit
my 'budget plan' to see if I can buy a pillar drill and clamp which I guess
won't be the full floor to standing height drill I really wanted.</DIV>
<DIV> </DIV>
<DIV>Regards</DIV>
<DIV> </DIV>
<DIV> </DIV>
<DIV>Daniel</DIV>
<DIV> </DIV>
<DIV>
<DIV>In a message dated 16/12/2016 21:34:29 GMT Standard Time,
spridgets@autox.team.net writes:</DIV>
<BLOCKQUOTE
style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: blue 2px solid"><FONT
style="BACKGROUND-COLOR: transparent" color=#000000 size=2
face=Arial>Daniel-Assuming a yield strength of 35ksi (typical for
304SS,18-8SS), The approximate yield point of load application is around 1100
lbs/in of thread. I'm referencing some work that I just did on #10-32 threads
which are a bit smaller than M6. Assuming that you have a 10" lever arm on the
handbrake handle (guessing here), that would require ~110 lbs of upward force
applied to the handle. This assumes no drag and no additional leverages (which
there are of both). Cold rolled steel ( your average steel for such things)
has a yield strength of 45-65 ksi, which means the cold rolled will yield with
~130lbs of upward force, therefore, if you increase your engaged, threaded
length of SS rod by 30+% over the stock CR steel, you should be fine.<BR><BR>
<DIV class=gmail_extra>
<DIV class=gmail_quote>
<BLOCKQUOTE class=gmail_quote
style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: rgb(204,204,204) 1px solid">Mark
Haynes<BR></BLOCKQUOTE>
<DIV>It only goes one way-Pay It Forward
<BR></DIV></DIV></DIV></FONT></BLOCKQUOTE></DIV></FONT></BODY></HTML>