[Spridgets] 1274 Sump replacement....

[cclabaw at juno.com]

Listers -

IMHO, checking the threaded holes in the block flange for 'pull-out' is very
worthwhile.  Any that protrude above the flange surface should be very lightly
chamfered to bring them down to flush.

Clay L.
'67 Sprite


-- Peter C <peter at nosimport.com> wrote:
I agree with Bob, except I don't trim the cork, or I use the newly
supplied rubber. Also, I use a small jack to hold the pan tight to
the block. Of course I am lying on my back. Maybe if I had a lift I'd
do it differently. Some folks invert the pan on the workbench with
the gaskets glued on and lots of weight on it overnight.
         Peter C.
====
At 11:41 PM 8/4/2008, Kitterer Bob wrote:
>Dave,
>
>Yes the sump can be replaced from underneath - do not have to pull,
>mover or other wise reposition the engine.  A 7/16 socket with a long
>extension makes for a quick and easy job.  The last time I did this
>the half circles were cork, maybe still are.  Anyway what worked for
>me was to press them into the slot on the pan then cut them with
>about a 1/8 inch over size on both sides.  This makes it a little
>harder to get the bolts started but compresses the cork for a good seal.
>
>Bob Kitterer
>
>1960 Austin Healey Sprite (Mk IV in disguise)
>1966 Austin Healey Sprite Mk III (Trevor) - still in boxes
>2000 Miata Special Edition
>
>
>
>
>On Aug 4, 2008, at 9:30 PM, Dave G. wrote:
>
> > Hi Folks,
> >
> > A question about the sump...
> >
> > I would like to replace the sump on The Beast.... it's been badly
> > bashed in
> > underneath! --- asper usual !!
> > I do have what I think is a fair condition replacement sump...
> > Here's the question(s)...
> > Can this be done from underneath without pulling the engine?
> > What do I do with the semi-circular cut-outs at the front and back
> > of the
> > sump?
> > I know they are for oil seals but is there a special trick to make
> > sure they
> > don't leak when I fit them?
> > I don't want to be another Exxon Valdez...
> >
> > Any other "hints and kinks" for doing this???
> >
> > TIA...
> > --
> > Dave G.   KK7SS
> > '65 MK III Sprite in Richland, WA
> >
> > The Original Point and Click  --- Smith and Wesson....
> > _______________________________________________
> > Support Team.Net  http://www.team.net/donate.html
> >
> > You are subscribed as bkitterer at mac.com
> >
> > http://www.team.net/archive
> >
> > http://autox.team.net/mailman/listinfo/spridgets
>_______________________________________________
>Support Team.Net  http://www.team.net/donate.html
>
>You are subscribed as peter at nosimport.com
>
>http://www.team.net/archive
>
>http://autox.team.net/mailman/listinfo/spridgets
You are subscribed as cclabaw at juno.com

http://www.team.net/archive

http://autox.team.net/mailman/listinfo/spridgets


____________________________________________________________
Click to learn about options trading and get the latest information.
http://thirdpartyoffers.juno.com/TGL2141/fc/Ioyw6i3m5bjEJlg9zukCG3GQSGOhNvGxN
XtHsC8RtJAfIYaJQIvCDy/