<div dir="ltr">About 1000 years ago when I was in A&P school I was taught to do style #2.  THe main reason is that someone will eventually need to reach their hand into a tight spot past the cotter pin you have installed.  If you used style #2, you are much less likely to leave sharp edges that will shred the hands of the next guy who has to work on this thing.  I actually had an instructor who would look for stuff like this and if she found that you left a sharp edge somewhere she would deliberately run you hand across it in a way as to cause just enough damage to get the point across.  Not a lesson I needed to have repeated.<br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Nov 17, 2020 at 11:40 AM Bob Spidell <<a href="mailto:bspidell@comcast.net">bspidell@comcast.net</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Got some 'quiet time' before I have to go look after my mom, and I <br>
thought I'd pose an arcane question to the List:<br>
<br>
What do y'all consider the proper way to use a cotter key/pin? I've <br>
watched the pros on TV--Edd China, Ant Anstead, Goblin Garage, <br>
Fantomworks, etc. and the 'Chop it/Channel It/Drop a Crate Engine In <br>
It/Bag It/Put Huge Dubs and a Gaudy Paint Job On It and Call It a Day' <br>
hotrod builders, and they all do it a bit different. Usually, it's 'Type <br>
1'--see terrible hand-drawn 'art' attached (using a stub axle for <br>
example)--but I gave it a lot of thought and wondered 'Is that the best <br>
way?' Thinking it through, yes, any way you put a cotter in and secure <br>
it will do the job; i.e. keep the nut from coming completely undone. <br>
However, when safety-wiring--a skill I sorta learned maintaining my own <br>
aircraft--you're supposed to always wire so as to pull in the tightening <br>
direction, to resist any turning at all of the nut/bolt. So, when <br>
applicable--e.g. on castellated nuts--I torque until the cotter will <br>
just fit in the hole (drawing# 2), situated 'sideways'--where you can't <br>
see the eye of the cotter from the side--snug against the side of the <br>
nut's slot so as to resist the nut turning at all. Then, I bend the <br>
upper half of the cotter back over the nut/spindle, and snip the lower <br>
half at the edge of the nut, figuring anything longer than that isn't <br>
doing anything (plus it just looks neater IMO, and may be easier to <br>
remove if necessary).<br>
<br>
FWIW, my late father, who was an auto shop teacher and had a few <br>
psychology classes under his belt said I was 'stuck at the anal <br>
retentive stage' of child development; I (think) he was kidding.<br>
<br>
Bob<br>
_______________________________________________<br>
<br>
<a href="mailto:Shop-talk@autox.team.net" target="_blank">Shop-talk@autox.team.net</a><br>
Donate: <a href="http://www.team.net/donate.html" rel="noreferrer" target="_blank">http://www.team.net/donate.html</a><br>
Suggested annual donation  $12.96<br>
Archive: <a href="http://www.team.net/pipermail/shop-talk" rel="noreferrer" target="_blank">http://www.team.net/pipermail/shop-talk</a> <a href="http://autox.team.net/archive" rel="noreferrer" target="_blank">http://autox.team.net/archive</a><br>
<br>
Unsubscribe/Manage: <a href="http://autox.team.net/mailman/options/shop-talk/jdinnis@gmail.com" rel="noreferrer" target="_blank">http://autox.team.net/mailman/options/shop-talk/jdinnis@gmail.com</a><br>
<br>
</blockquote></div><br clear="all"><br>-- <br><div dir="ltr" class="gmail_signature">=================================<br>= Never offend people with style when you   =<br>= can offend with substance --- Sam Brown  =<br>=================================</div>