<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body text="#000000" bgcolor="#FFFFFF">
I second the router guide shown in the video if you don't have a
local shop with a door sized industrial sander.<br>
<br>
Brian<br>
<br>
<div class="moz-cite-prefix">On 12/22/2019 10:08 AM, Miq Millman via
Shop-talk wrote:<br>
</div>
<blockquote type="cite"
cite="mid:CALUbS3E6Z1bQErv0sihka3z5gL_at6ghfoqfq38GwKPQEP4H=w@mail.gmail.com">
<meta http-equiv="content-type" content="text/html; charset=UTF-8">
<div dir="ltr">I just did something similar: had a door that was
too wide, so I used a router to make the hinge pockets 1/4"
deeper then ran the door through my table saw and sliced a bit
less than 3/16" of the hinge side and about 1/16" off the latch
side.
<div><br>
</div>
<div>I think you can do something similar. Look up "router jig
to flatten wood" and make a sled that is roughly 31" long and
as wide as your (possibly new) router base. Woodworkers use
this kind of rig for flattening live edge slabs and the like.</div>
<div><br>
</div>
<div>Here's a good video that explains it and shows how to make
it using some plywood and simple rails: <a
href="https://www.youtube.com/watch?v=J0SDvKHcL5M"
moz-do-not-send="true">https://www.youtube.com/watch?v=J0SDvKHcL5M</a></div>
<div><br>
</div>
<div>Basically, you get a nice wide straight bit and set the jig
on the door, then make passes cutting off 1/8" or less at a
time. Make a pass, move the jig less than the diameter of the
bit, make another pass, etc.</div>
<div><br>
</div>
<div>You might not even need to finish the final surface with a
plane, but here's a chance to get a nice jack plane, like the
Stanley No. 62 (Orange big box has them for ~$100).</div>
<div><br>
</div>
<div>I've done this, for end grain cutting boards, where I used
a 1x2" aluminum rectangle tube for the rails,</div>
<div><br clear="all">
<div>
<div dir="ltr" class="gmail_signature"
data-smartmail="gmail_signature">--<br>
__<br>
Miq Millman <a href="mailto:miq@bigllama.com"
target="_blank" moz-do-not-send="true">miq@bigllama.com</a><br>
Tualatin, OR Big Llama Productions<br>
</div>
</div>
<br>
</div>
</div>
<br>
<div class="gmail_quote">
<div dir="ltr" class="gmail_attr">On Sun, Dec 22, 2019 at 6:26
AM Jim Stone via Shop-talk <<a
href="mailto:shop-talk@autox.team.net"
moz-do-not-send="true">shop-talk@autox.team.net</a>>
wrote:<br>
</div>
<blockquote class="gmail_quote" style="margin:0px 0px 0px
0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
<div style="overflow-wrap: break-word;">
<div>I am installing a barn door in my recently remodeled
house and have come up with a problem I would like the
group’s help with. I need to put up a pair of 8’ x 30"
barn doors, one of which will slide in next to a tall
kitchen cabinet. So, not exactly a pocket door, but it
needs to fit into a pocket. When we designed/installed
the kitchen cabinets we planned the cabinets for a 1 3/8”
- 1 1/2” door, which I planned to make out of tongue and
groove boards or possibly shiplap. However, my wife has
lately decided that she doesn’t like the look of the board
door and wants to try something different. I wanted to
install something temporary while she shops and decides
and we went to Habitat for Humanity’s ReStore yesterday to
see if they had anything that would cheaply do the trick,
at least for the holidays. To our surprise, they had a
pair of new, really nice, 8x30 shaker style doors for $50
each that would look really good in the house. They are
solid wood, I think poplar, and the only problem is that
they are 1 3/4” thick. I bought them anyway, figuring I
could always donate them back if there wasn’t a good way
to make them work. </div>
<div><br>
</div>
<div>There is a possibility that I might be able to make the
doors work by tweaking the barn door hardware, as the
opening is about 1 5/8”. I will try that, but doubt the
wall tolerances are that precise. It it doesn’t work, my
only option - besides re-donating the doors - is to try to
narrow the doors a bit. This <i>should</i> be possible,
since the stiles and rails are 4” and 8”, respectively, so
I am not talking about narrowing the entire width of the
door. </div>
<div>(For what it is worth, I should add here that while the
doors are currently 8x30, I need to tweak that a bit to
make the match the cabinets and door opening and will be
cutting them down to about 84” x 29”. </div>
<div><br>
</div>
<div>I currently have a good bench top planer that I can’t
see anyway to use, and a cheap HF hand planer that might
work. But, of course, I would be happy to buy a new one
or another tool that would do the job. We are probably
looking at more than $1000 for a pair of 8’ doors that
make my wife happy, so there is lots of room in the budget
for a new tool. So, what does the group think? Can I
safely take about 1/8” off each face of these doors. Is
an electric hand planer my best option, or is there
another way? They will be painted in the end, so I can
fill in any random gouges, but they do have to be smooth
and even.</div>
<div><br>
</div>
<div>As always, thanks for any advice and Happy Holidays to
all!</div>
<div><br>
</div>
<div>Jim</div>
</div>
_______________________________________________<br>
<br>
<a href="mailto:Shop-talk@autox.team.net" target="_blank"
moz-do-not-send="true">Shop-talk@autox.team.net</a><br>
Donate: <a href="http://www.team.net/donate.html"
rel="noreferrer" target="_blank" moz-do-not-send="true">http://www.team.net/donate.html</a><br>
Suggested annual donation $12.96<br>
Archive: <a href="http://www.team.net/pipermail/shop-talk"
rel="noreferrer" target="_blank" moz-do-not-send="true">http://www.team.net/pipermail/shop-talk</a>
<a href="http://autox.team.net/archive" rel="noreferrer"
target="_blank" moz-do-not-send="true">http://autox.team.net/archive</a><br>
<br>
Unsubscribe/Manage: <a
href="http://autox.team.net/mailman/options/shop-talk/miq@bigllama.com"
rel="noreferrer" target="_blank" moz-do-not-send="true">http://autox.team.net/mailman/options/shop-talk/miq@bigllama.com</a><br>
<br>
</blockquote>
</div>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<pre class="moz-quote-pre" wrap="">_______________________________________________
<a class="moz-txt-link-abbreviated" href="mailto:Shop-talk@autox.team.net" moz-do-not-send="true">Shop-talk@autox.team.net</a>
Donate: <a class="moz-txt-link-freetext" href="http://www.team.net/donate.html" moz-do-not-send="true">http://www.team.net/donate.html</a>
Suggested annual donation $12.96
Archive: <a class="moz-txt-link-freetext" href="http://www.team.net/pipermail/shop-talk" moz-do-not-send="true">http://www.team.net/pipermail/shop-talk</a> <a class="moz-txt-link-freetext" href="http://autox.team.net/archive" moz-do-not-send="true">http://autox.team.net/archive</a>
Unsubscribe/Manage: <a class="moz-txt-link-freetext" href="http://autox.team.net/mailman/options/shop-talk/bk13@earthlink.net" moz-do-not-send="true">http://autox.team.net/mailman/options/shop-talk/bk13@earthlink.net</a>
</pre>
</blockquote>
<br>
</body>
</html>