From fishplate at gmail.com Tue Oct 1 08:43:25 2024 From: fishplate at gmail.com (Jeff Scarbrough) Date: Tue, 1 Oct 2024 10:43:25 -0400 Subject: [Shop-talk] Air In-Reply-To: References: Message-ID: Hi Mike, Is that the regulator knob? Might be stuck or broken inside. A picture of what you're looking at would help - the online parts diagrams I found look like one of those joke lists from the 80s that had been faxed a hundred times. -- Jeff On Mon, Sep 30, 2024 at 7:43?PM Mike Sinclair wrote: > I have a very old small air compressor that compresses ok, but I no longer > can get it to send air to the outlet. There is a hand valve between the > gages that turns ok, but doesn't open the valve. It doesn't close it very > well, either. The knob turns fine, and bottoms out in both directions, but > nothing happens. Is it possible to buy a replacement? I'm hoping it's > just a simple remove and replace. > > Sears Model 916-176311. > > Mike > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation $12.96 > Archive: http://www.team.net/pipermail/shop-talk > http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/fishplate at gmail.com > > -------------- next part -------------- An HTML attachment was scrubbed... URL: From phoenix722 at comcast.net Tue Oct 1 09:44:44 2024 From: phoenix722 at comcast.net (Mike Sinclair) Date: Tue, 1 Oct 2024 08:44:44 -0700 Subject: [Shop-talk] Air In-Reply-To: References: Message-ID: <1d49b375-d4aa-49b8-9f4e-482c8ffa2cb6@comcast.net> Some pictures attached.? The black thing.? I looked on the internet and found several parts sources, but nobody seems to carry this valve.? My experience with Sears is that they had many parts that were only available thru them.? I did take it apart and it looks fine.? Thought maybe it was just dirty. Mike On 10/1/24 7:43 AM, Jeff Scarbrough wrote: > Hi Mike, > > Is that the regulator knob?? Might be stuck or broken inside.? A > picture of what you're looking at would help - the online parts > diagrams I found look like one of those joke lists from the 80s that > had been faxed a hundred times. > > -- Jeff > > On Mon, Sep 30, 2024 at 7:43?PM Mike Sinclair > wrote: > > I have a very old small air compressor that compresses ok, but I > no longer can get it to send air to the outlet.? There is a hand > valve between the gages that turns ok, but doesn't open the > valve.? It doesn't close it very well, either.? The knob turns > fine, and bottoms out in both directions, but nothing happens.? Is > it possible to buy a replacement? I'm hoping it's just a simple > remove and replace. > > Sears Model 916-176311. > > Mike > > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation? $12.96 > Archive: http://www.team.net/pipermail/shop-talk > http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/fishplate at gmail.com > -------------- next part -------------- An HTML attachment was scrubbed... URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: IMG_0904.JPG Type: image/jpeg Size: 94463 bytes Desc: not available URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: IMG_0905.JPG Type: image/jpeg Size: 98864 bytes Desc: not available URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: IMG_0906.JPG Type: image/jpeg Size: 95529 bytes Desc: not available URL: From dmscheidt at gmail.com Tue Oct 1 09:56:55 2024 From: dmscheidt at gmail.com (David Scheidt) Date: Tue, 1 Oct 2024 10:56:55 -0500 Subject: [Shop-talk] Air In-Reply-To: References: Message-ID: On Mon, Sep 30, 2024 at 6:44?PM Mike Sinclair wrote: > > I have a very old small air compressor that compresses ok, but I no longer can get it to send air to the outlet. There is a hand valve between the gages that turns ok, but doesn't open the valve. It doesn't close it very well, either. The knob turns fine, and bottoms out in both directions, but nothing happens. Is it possible to buy a replacement? I'm hoping it's just a simple remove and replace. I agree with Jeff, it sounds like the regulator. They are easy to replace. If you can't get an exact fit, replacing all the plumbing from the tank outlet to the air outlet is pretty easy, and parts are cheap. (I replaced the pressure switch, regulator, and gauges a couple years ago for a similar compressor for about $30.) Pictures would help someone tell you what you'd need. -- David Scheidt dmscheidt at gmail.com From phoenix722 at comcast.net Tue Oct 1 12:22:04 2024 From: phoenix722 at comcast.net (Mike Sinclair) Date: Tue, 1 Oct 2024 11:22:04 -0700 Subject: [Shop-talk] Air In-Reply-To: References: Message-ID: <4f64b88d-eae0-4db5-a4ba-614645b69b39@comcast.net> Thanks all for the advice.? Turned out the regulator is ok, but the plastic knob is connected via some very shallow splines on the stem, and doesn't connect well.? I wrapped the stem with Teflon tape and it works ok, but I need to find a better way.? I'll check at my favorite old-fashioned hardware store for a knob. Mike On 10/1/24 7:43 AM, Jeff Scarbrough wrote: > Hi Mike, > > Is that the regulator knob?? Might be stuck or broken inside.? A > picture of what you're looking at would help - the online parts > diagrams I found look like one of those joke lists from the 80s that > had been faxed a hundred times. > > -- Jeff > > On Mon, Sep 30, 2024 at 7:43?PM Mike Sinclair > wrote: > > I have a very old small air compressor that compresses ok, but I > no longer can get it to send air to the outlet.? There is a hand > valve between the gages that turns ok, but doesn't open the > valve.? It doesn't close it very well, either.? The knob turns > fine, and bottoms out in both directions, but nothing happens.? Is > it possible to buy a replacement? I'm hoping it's just a simple > remove and replace. > > Sears Model 916-176311. > > Mike > > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation? $12.96 > Archive: http://www.team.net/pipermail/shop-talk > http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/fishplate at gmail.com > -------------- next part -------------- An HTML attachment was scrubbed... URL: From alfuller194 at gmail.com Tue Oct 1 13:53:07 2024 From: alfuller194 at gmail.com (alfuller194 at gmail.com) Date: Tue, 1 Oct 2024 12:53:07 -0700 Subject: [Shop-talk] Air In-Reply-To: <4f64b88d-eae0-4db5-a4ba-614645b69b39@comcast.net> References: <4f64b88d-eae0-4db5-a4ba-614645b69b39@comcast.net> Message-ID: Mike ? when I went out to look at my Craftsman compressor that has the same setup, I noticed that the regulator knob says ?pull to adjust?. I assume it has some splined interface between the outer knob and the inner knob to prevent accidental mis-adjustment. If you have been able to get the adjustment you need using Teflon tape as an interface you are probably good to go. The only other thing that comes to mind is whether they spent the extra money on that setup to compensate for the vibration generated when the unit is running. This is just pure speculation, but you might want to keep an eye out and ensure the pressure stays where you set it after the modification. ----------------------------------- All the best, Al Fuller From: Shop-talk On Behalf Of Mike Sinclair Sent: Tuesday, October 1, 2024 11:22 AM To: Jeff Scarbrough Cc: shop-talk at autox.team.net Subject: Re: [Shop-talk] Air Thanks all for the advice. Turned out the regulator is ok, but the plastic knob is connected via some very shallow splines on the stem, and doesn't connect well. I wrapped the stem with Teflon tape and it works ok, but I need to find a better way. I'll check at my favorite old-fashioned hardware store for a knob. Mike On 10/1/24 7:43 AM, Jeff Scarbrough wrote: Hi Mike, Is that the regulator knob? Might be stuck or broken inside. A picture of what you're looking at would help - the online parts diagrams I found look like one of those joke lists from the 80s that had been faxed a hundred times. -- Jeff On Mon, Sep 30, 2024 at 7:43?PM Mike Sinclair > wrote: I have a very old small air compressor that compresses ok, but I no longer can get it to send air to the outlet. There is a hand valve between the gages that turns ok, but doesn't open the valve. It doesn't close it very well, either. The knob turns fine, and bottoms out in both directions, but nothing happens. Is it possible to buy a replacement? I'm hoping it's just a simple remove and replace. Sears Model 916-176311. Mike _______________________________________________ Shop-talk at autox.team.net Donate: http://www.team.net/donate.html Suggested annual donation $12.96 Archive: http://www.team.net/pipermail/shop-talk http://autox.team.net/archive Unsubscribe/Manage: http://autox.team.net/mailman/options/shop-talk/fishplate at gmail.com -------------- next part -------------- An HTML attachment was scrubbed... URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: image001.jpg Type: image/jpeg Size: 2643293 bytes Desc: not available URL: From stearman809 at gmail.com Tue Oct 1 16:10:25 2024 From: stearman809 at gmail.com (Karl Vacek) Date: Tue, 01 Oct 2024 17:10:25 -0500 Subject: [Shop-talk] Air In-Reply-To: References: <4f64b88d-eae0-4db5-a4ba-614645b69b39@comcast.net> Message-ID: <1924a227468.2898.cd27845553c78383775132770b7455be@gmail.com> My aircraft cylinder bleed down gauge uses one of those same goofy Chinese regulators, which well-meaning helpers have broken a few times. It has responded to epoxy and stern warnings to helpers to just let me adjust it. Karl On October 1, 2024 3:11:30 PM wrote: > Mike ? when I went out to look at my Craftsman compressor that has the same > setup, I noticed that the regulator knob says ?pull to adjust?. I assume it > has some splined interface between the outer knob and the inner knob to > prevent accidental mis-adjustment. > > If you have been able to get the adjustment you need using Teflon tape as > an interface you are probably good to go. The only other thing that comes > to mind is whether they spent the extra money on that setup to compensate > for the vibration generated when the unit is running. This is just pure > speculation, but you might want to keep an eye out and ensure the pressure > stays where you set it after the modification. > > > > ----------------------------------- > All the best, > > Al Fuller > > From: Shop-talk On Behalf Of Mike Sinclair > Sent: Tuesday, October 1, 2024 11:22 AM > To: Jeff Scarbrough > Cc: shop-talk at autox.team.net > Subject: Re: [Shop-talk] Air > > Thanks all for the advice. Turned out the regulator is ok, but the plastic > knob is connected via some very shallow splines on the stem, and doesn't > connect well. I wrapped the stem with Teflon tape and it works ok, but I > need to find a better way. I'll check at my favorite old-fashioned > hardware store for a knob. > Mike > On 10/1/24 7:43 AM, Jeff Scarbrough wrote: > Hi Mike, > > Is that the regulator knob? Might be stuck or broken inside. A picture of > what you're looking at would help - the online parts diagrams I found look > like one of those joke lists from the 80s that had been faxed a hundred times. > > -- Jeff > > On Mon, Sep 30, 2024 at 7:43?PM Mike Sinclair wrote: > I have a very old small air compressor that compresses ok, but I no longer > can get it to send air to the outlet. There is a hand valve between the > gages that turns ok, but doesn't open the valve. It doesn't close it very > well, either. The knob turns fine, and bottoms out in both directions, but > nothing happens. Is it possible to buy a replacement? I'm hoping it's > just a simple remove and replace. > Sears Model 916-176311. > Mike > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation $12.96 > Archive: http://www.team.net/pipermail/shop-talk http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/fishplate at gmail.com > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation $12.96 > Archive: http://www.team.net/pipermail/shop-talk http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/stearman809 at gmail.com -------------- next part -------------- An HTML attachment was scrubbed... URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: INL1 Type: image/jpeg Size: 2643293 bytes Desc: not available URL: From phoenix722 at comcast.net Tue Oct 1 17:46:57 2024 From: phoenix722 at comcast.net (Mike Sinclair) Date: Tue, 1 Oct 2024 16:46:57 -0700 Subject: [Shop-talk] Air In-Reply-To: <1924a227468.2898.cd27845553c78383775132770b7455be@gmail.com> References: <4f64b88d-eae0-4db5-a4ba-614645b69b39@comcast.net> <1924a227468.2898.cd27845553c78383775132770b7455be@gmail.com> Message-ID: Both good ideas! Mike On 10/1/24 3:10 PM, Karl Vacek wrote: > My aircraft cylinder bleed down gauge uses one of those same goofy > Chinese regulators, which well-meaning helpers have broken a few times. > > It has responded to epoxy and stern warnings to helpers to just let me > adjust it. > > Karl > > On October 1, 2024 3:11:30 PM wrote: > >> Mike ? when I went out to look at my Craftsman compressor that has >> the same setup, I noticed that the regulator knob says ?pull to >> adjust?. I assume it has some splined interface between the outer >> knob and the inner knob to prevent accidental mis-adjustment. >> >> If you have been able to get the adjustment you need using Teflon >> tape as an interface you are probably good to go. The only other >> thing that comes to mind is whether they spent the extra money on >> that setup to compensate for the vibration generated when the unit is >> running. This is just pure speculation, but you might want to keep an >> eye out and ensure the pressure stays where you set it after the >> modification. >> >> ----------------------------------- >> >> All the best, >> >> Al Fuller >> >> *From:*Shop-talk *On Behalf Of >> *Mike Sinclair >> *Sent:* Tuesday, October 1, 2024 11:22 AM >> *To:* Jeff Scarbrough >> *Cc:* shop-talk at autox.team.net >> *Subject:* Re: [Shop-talk] Air >> >> Thanks all for the advice.? Turned out the regulator is ok, but the >> plastic knob is connected via some very shallow splines on the stem, >> and doesn't connect well.? I wrapped the stem with Teflon tape and it >> works ok, but I need to find a better way. I'll check at my favorite >> old-fashioned hardware store for a knob. >> >> Mike >> >> On 10/1/24 7:43 AM, Jeff Scarbrough wrote: >> >> Hi Mike, >> >> Is that the regulator knob?? Might be stuck or broken inside.? A >> picture of what you're looking at would help - the online parts >> diagrams I found look like one of those joke lists from the 80s >> that had been faxed a hundred times. >> >> -- Jeff >> >> On Mon, Sep 30, 2024 at 7:43?PM Mike Sinclair >> wrote: >> >> I have a very old small air compressor that compresses ok, >> but I no longer can get it to send air to the outlet.? There >> is a hand valve between the gages that turns ok, but doesn't >> open the valve.? It doesn't close it very well, either.? The >> knob turns fine, and bottoms out in both directions, but >> nothing happens.? Is it possible to buy a replacement?? I'm >> hoping it's just a simple remove and replace. >> >> Sears Model 916-176311. >> >> Mike >> >> _______________________________________________ >> >> Shop-talk at autox.team.net >> Donate: http://www.team.net/donate.html >> Suggested annual donation? $12.96 >> Archive: http://www.team.net/pipermail/shop-talk >> http://autox.team.net/archive >> >> Unsubscribe/Manage: >> http://autox.team.net/mailman/options/shop-talk/fishplate at gmail.com >> >> _______________________________________________ >> >> Shop-talk at autox.team.net >> Donate: http://www.team.net/donate.html >> Suggested annual donation? $12.96 >> Archive: http://www.team.net/pipermail/shop-talk >> >> http://autox.team.net/archive >> >> Unsubscribe/Manage: >> http://autox.team.net/mailman/options/shop-talk/stearman809 at gmail.com >> >> >> > > > _______________________________________________ > > Shop-talk at autox.team.net > Donate:http://www.team.net/donate.html > Suggested annual donation $12.96 > Archive:http://www.team.net/pipermail/shop-talk http://autox.team.net/archive > > Unsubscribe/Manage:http://autox.team.net/mailman/options/shop-talk/phoenix722 at comcast.net > -------------- next part -------------- An HTML attachment was scrubbed... URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: INL1 Type: image/png Size: 2643293 bytes Desc: not available URL: From phoenix722 at comcast.net Tue Oct 1 17:47:44 2024 From: phoenix722 at comcast.net (Mike Sinclair) Date: Tue, 1 Oct 2024 16:47:44 -0700 Subject: [Shop-talk] Air In-Reply-To: References: <4f64b88d-eae0-4db5-a4ba-614645b69b39@comcast.net> Message-ID: Thanks.? No "pull to adjust".? Just a plastic knob that is softer than the metal stem splines.? This unit is probably 30 years old. Mike On 10/1/24 12:53 PM, alfuller194 at gmail.com wrote: > > Mike ? when I went out to look at my Craftsman compressor that has the > same setup, I noticed that the regulator knob says ?pull to adjust?. I > assume it has some splined interface between the outer knob and the > inner knob to prevent accidental mis-adjustment. > > If you have been able to get the adjustment you need using Teflon tape > as an interface you are probably good to go. The only other thing that > comes to mind is whether they spent the extra money on that setup to > compensate for the vibration generated when the unit is running. This > is just pure speculation, but you might want to keep an eye out and > ensure the pressure stays where you set it after the modification. > > ----------------------------------- > > All the best, > > Al Fuller > > *From:*Shop-talk *On Behalf Of > *Mike Sinclair > *Sent:* Tuesday, October 1, 2024 11:22 AM > *To:* Jeff Scarbrough > *Cc:* shop-talk at autox.team.net > *Subject:* Re: [Shop-talk] Air > > Thanks all for the advice.? Turned out the regulator is ok, but the > plastic knob is connected via some very shallow splines on the stem, > and doesn't connect well.? I wrapped the stem with Teflon tape and it > works ok, but I need to find a better way.? I'll check at my favorite > old-fashioned hardware store for a knob. > > Mike > > On 10/1/24 7:43 AM, Jeff Scarbrough wrote: > > Hi Mike, > > Is that the regulator knob?? Might be stuck or broken inside.? A > picture of what you're looking at would help - the online parts > diagrams I found look like one of those joke lists from the 80s > that had been faxed a hundred times. > > -- Jeff > > On Mon, Sep 30, 2024 at 7:43?PM Mike Sinclair > wrote: > > I have a very old small air compressor that compresses ok, but > I no longer can get it to send air to the outlet.? There is a > hand valve between the gages that turns ok, but doesn't open > the valve.? It doesn't close it very well, either.? The knob > turns fine, and bottoms out in both directions, but nothing > happens.? Is it possible to buy a replacement?? I'm hoping > it's just a simple remove and replace. > > Sears Model 916-176311. > > Mike > > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation? $12.96 > Archive: http://www.team.net/pipermail/shop-talk > http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/fishplate at gmail.com > > > _______________________________________________ > > Shop-talk at autox.team.net > Donate:http://www.team.net/donate.html > Suggested annual donation $12.96 > Archive:http://www.team.net/pipermail/shop-talk http://autox.team.net/archive > > Unsubscribe/Manage:http://autox.team.net/mailman/options/shop-talk/phoenix722 at comcast.net > -------------- next part -------------- An HTML attachment was scrubbed... URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: image001.jpg Type: image/jpeg Size: 2643293 bytes Desc: not available URL: From alfuller194 at gmail.com Tue Oct 1 19:34:42 2024 From: alfuller194 at gmail.com (alfuller194 at gmail.com) Date: Tue, 1 Oct 2024 18:34:42 -0700 Subject: [Shop-talk] Air In-Reply-To: References: <4f64b88d-eae0-4db5-a4ba-614645b69b39@comcast.net>

Message-ID: Yeah ? this one is likely that old too. It?s getting pretty noisy and I don?t want to spend the time to find a new cylinder for it, which would quiet it down. The good thing is I don?t need to use it a lot these days. I could probably get by with something a lot smaller and quieter. ----------------------------------- All the best, Al Fuller From: Shop-talk On Behalf Of Mike Sinclair Sent: Tuesday, October 1, 2024 4:48 PM To: shop-talk at autox.team.net Subject: Re: [Shop-talk] Air Thanks. No "pull to adjust". Just a plastic knob that is softer than the metal stem splines. This unit is probably 30 years old. Mike On 10/1/24 12:53 PM, alfuller194 at gmail.com wrote: Mike ? when I went out to look at my Craftsman compressor that has the same setup, I noticed that the regulator knob says ?pull to adjust?. I assume it has some splined interface between the outer knob and the inner knob to prevent accidental mis-adjustment. If you have been able to get the adjustment you need using Teflon tape as an interface you are probably good to go. The only other thing that comes to mind is whether they spent the extra money on that setup to compensate for the vibration generated when the unit is running. This is just pure speculation, but you might want to keep an eye out and ensure the pressure stays where you set it after the modification. ----------------------------------- All the best, Al Fuller From: Shop-talk

On Behalf Of Mike Sinclair Sent: Tuesday, October 1, 2024 11:22 AM To: Jeff Scarbrough Cc: shop-talk at autox.team.net Subject: Re: [Shop-talk] Air Thanks all for the advice. Turned out the regulator is ok, but the plastic knob is connected via some very shallow splines on the stem, and doesn't connect well. I wrapped the stem with Teflon tape and it works ok, but I need to find a better way. I'll check at my favorite old-fashioned hardware store for a knob. Mike On 10/1/24 7:43 AM, Jeff Scarbrough wrote: Hi Mike, Is that the regulator knob? Might be stuck or broken inside. A picture of what you're looking at would help - the online parts diagrams I found look like one of those joke lists from the 80s that had been faxed a hundred times. -- Jeff On Mon, Sep 30, 2024 at 7:43?PM Mike Sinclair > wrote: I have a very old small air compressor that compresses ok, but I no longer can get it to send air to the outlet. There is a hand valve between the gages that turns ok, but doesn't open the valve. It doesn't close it very well, either. The knob turns fine, and bottoms out in both directions, but nothing happens. Is it possible to buy a replacement? I'm hoping it's just a simple remove and replace. Sears Model 916-176311. Mike _______________________________________________ Shop-talk at autox.team.net Donate: http://www.team.net/donate.html Suggested annual donation $12.96 Archive: http://www.team.net/pipermail/shop-talk http://autox.team.net/archive Unsubscribe/Manage: http://autox.team.net/mailman/options/shop-talk/fishplate at gmail.com _______________________________________________ Shop-talk at autox.team.net Donate: http://www.team.net/donate.html Suggested annual donation $12.96 Archive: http://www.team.net/pipermail/shop-talk http://autox.team.net/archive Unsubscribe/Manage: http://autox.team.net/mailman/options/shop-talk/phoenix722 at comcast.net -------------- next part -------------- An HTML attachment was scrubbed... URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: image001.jpg Type: image/jpeg Size: 2643293 bytes Desc: not available URL: From fishplate at gmail.com Mon Oct 14 10:02:16 2024 From: fishplate at gmail.com (Jeff Scarbrough) Date: Mon, 14 Oct 2024 12:02:16 -0400 Subject: [Shop-talk] Shop/Garage Floor Coating Message-ID: Got a question for the group: I'm having my shop floor coated. They are using a polyaspartic coating after floor prep (surface grinding. My question is related to the finish: They can leave it as is with the self-leveling (glossyish) finish, or they can put some grit in it to give it more traction. I've had experience in laboratory construction, where the expectation is that the floor will be washed often and thus wet, so a grit is usually used to provide traction. But the grit can make mopping more complicated as it drags the mop. Plus, it just looks funny, like it has dirt on it. I can get a number of grit particle sizes and densities, but I keep wondering if I'll really need it. I plan to keep the floor dry and clean up any spills as they are made. I won't typically bring in a wet or snow-covered car. I generally wear shoes in the shop, and my shoes generally have tread. I'd appreciate any insight from those who have coated a floor and gone smooth or gritty, and how you feel about your choice. TIA, Jeff -------------- next part -------------- An HTML attachment was scrubbed... URL: From shop-talk2 at mcfetridge.org Mon Oct 14 10:54:41 2024 From: shop-talk2 at mcfetridge.org (Ian McFetridge) Date: Mon, 14 Oct 2024 12:54:41 -0400 Subject: [Shop-talk] Shop/Garage Floor Coating In-Reply-To: References: Message-ID: I did one garage with grit (flakes) and the other without. The grit definitely adds traction, I feel more than once on the smooth one. As you said the smooth cleaned up much easier, in particular, it was simple to spray and squeegee clean. If I did it again I?d go with light grit as I get old and bounce less. On Mon, Oct 14, 2024 at 12:13 PM Jeff Scarbrough wrote: > Got a question for the group: > > I'm having my shop floor coated. They are using a polyaspartic coating > after floor prep (surface grinding. My question is related to the finish: > They can leave it as is with the self-leveling (glossyish) finish, or they > can put some grit in it to give it more traction. > > I've had experience in laboratory construction, where the expectation is > that the floor will be washed often and thus wet, so a grit is usually used > to provide traction. But the grit can make mopping more complicated as it > drags the mop. Plus, it just looks funny, like it has dirt on it. > > I can get a number of grit particle sizes and densities, but I keep > wondering if I'll really need it. I plan to keep the floor dry and clean > up any spills as they are made. I won't typically bring in a wet or > snow-covered car. I generally wear shoes in the shop, and my shoes > generally have tread. > > I'd appreciate any insight from those who have coated a floor and gone > smooth or gritty, and how you feel about your choice. > > TIA, > Jeff > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation $12.96 > Archive: http://www.team.net/pipermail/shop-talk > http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/shop-talk2 at mcfetridge.org > > -------------- next part -------------- An HTML attachment was scrubbed... URL: From JIBrooks at live.com Mon Oct 14 15:09:55 2024 From: JIBrooks at live.com (Jack Brooks) Date: Mon, 14 Oct 2024 21:09:55 +0000 Subject: [Shop-talk] Shop/Garage Floor Coating In-Reply-To: References: Message-ID: Jeff, I worked in the industrial side of Epoxy coatings some years ago and we required they sign our ?Release of Liability? document from the client stating they understood how slick a non-textured floor can be before we would install it. If you figure you will ever have oil or other lubricants on your garage floor, I?d strongly suggest at least a light texture. Jack From: Shop-talk On Behalf Of Jeff Scarbrough Sent: Monday, October 14, 2024 9:02 AM To: shop-talk at autox.team.net Subject: [Shop-talk] Shop/Garage Floor Coating Got a question for the group: I'm having my shop floor coated. They are using a polyaspartic coating after floor prep (surface grinding. My question is related to the finish: They can leave it as is with the self-leveling (glossyish) finish, or they can put some grit in it to give it more traction. I've had experience in laboratory construction, where the expectation is that the floor will be washed often and thus wet, so a grit is usually used to provide traction. But the grit can make mopping more complicated as it drags the mop. Plus, it just looks funny, like it has dirt on it. I can get a number of grit particle sizes and densities, but I keep wondering if I'll really need it. I plan to keep the floor dry and clean up any spills as they are made. I won't typically bring in a wet or snow-covered car. I generally wear shoes in the shop, and my shoes generally have tread. I'd appreciate any insight from those who have coated a floor and gone smooth or gritty, and how you feel about your choice. TIA, Jeff -------------- next part -------------- An HTML attachment was scrubbed... URL: From jniolon at att.net Thu Oct 17 05:23:59 2024 From: jniolon at att.net (john niolon) Date: Thu, 17 Oct 2024 06:23:59 -0500 Subject: [Shop-talk] video editor software References: <1UheSHYA6q.1BGIRYtbzu3.ref@johns-desktop> Message-ID: <1UheSHYA6q.1BGIRYtbzu3@johns-desktop> I made a iPhone video (,mov file) that I need to edit the length... cut out the beginning and end and save the juicy part in the middle anyone suggest a program/app that works... I tried Canva and Ivideo but never found how to edit that way shop content... video is made of doing stuff in my shop thanks john -------------- next part -------------- An HTML attachment was scrubbed... URL: From alfuller194 at gmail.com Thu Oct 17 12:40:37 2024 From: alfuller194 at gmail.com (alfuller194 at gmail.com) Date: Thu, 17 Oct 2024 11:40:37 -0700 Subject: [Shop-talk] video editor software In-Reply-To: <1UheSHYA6q.1BGIRYtbzu3@johns-desktop> References: <1UheSHYA6q.1BGIRYtbzu3.ref@johns-desktop> <1UheSHYA6q.1BGIRYtbzu3@johns-desktop> Message-ID: <16a4901db20c4$0fc1f590$2f45e0b0$@gmail.com> John ? you could try the free VLC video player. It has basic cropping, so you could use it for a 1-off [as opposed to regular use in video editing]. The program is available here: https://www.videolan.org/vlc/ Apparently, you have to actually play the video, starting and stopping where you want the crop. While that?s fine for a single video, I wouldn?t want to have to put up with that regularly. I tried it with a .mov someone sent me and it cropped it just fine. I found a decent guide on using VLC for cropping and other video manipulation here: https://www.videoconverterfactory.com/tips/vlc-video-editor.html The guides I found wee not clear on where to find the cropped video. It looks like the default location on a Windows PC is the Videos folder, but you could set a different default before you did the cropping. If you are working in Linux or some other OS like the Apple Linux variants, I?m unsure whether the instructions hold. ----------------------------------- All the best, Al Fuller From: Shop-talk On Behalf Of john niolon Sent: Thursday, October 17, 2024 4:24 AM To: shop-talk Subject: [Shop-talk] video editor software I made a iPhone video (,mov file) that I need to edit the length... cut out the beginning and end and save the juicy part in the middle anyone suggest a program/app that works... I tried Canva and Ivideo but never found how to edit that way shop content... video is made of doing stuff in my shop thanks john -------------- next part -------------- An HTML attachment was scrubbed... URL: From lee at automate-it.com Thu Oct 17 13:10:18 2024 From: lee at automate-it.com (lee at automate-it.com) Date: Thu, 17 Oct 2024 14:10:18 -0500 Subject: [Shop-talk] video editor software In-Reply-To: <1UheSHYA6q.1BGIRYtbzu3@johns-desktop> References: <1UheSHYA6q.1BGIRYtbzu3.ref@johns-desktop> <1UheSHYA6q.1BGIRYtbzu3@johns-desktop> Message-ID: John - It may depend on which iPhone you have, but on mine (I have both iPhone-11 and -12), you can crop the ends of the video right there on your phone. Open the video (in Photos), at the top you should see an "Edit" button, that allows sliders (red circle in screen-shot below) at the bottom that you can use to crop from either/both ends. It's a little tricky to activate the sliders - mine is white for just scrolling, but turns yellow (as below) when you've grabbed it for cropping. When you're done, you can overwrite the current video or save it as a new one. I hope this helps! Lee On 2024-10-17 06:23, john niolon wrote: > I made a iPhone video (,mov file) that I need to edit the length... cut > out the beginning and end and save the juicy part in the middle > > anyone suggest a program/app that works... I tried Canva and Ivideo but > never found how to edit that way > > shop content... video is made of doing stuff in my shop > thanks > john > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation $12.96 > Archive: http://www.team.net/pipermail/shop-talk > http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/lee at automate-it.com -------------- next part -------------- An HTML attachment was scrubbed... URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: c99877a7.jpeg Type: image/jpeg Size: 262133 bytes Desc: not available URL: From neiljsherry at talktalk.net Thu Oct 17 13:40:41 2024 From: neiljsherry at talktalk.net (neiljsherry at talktalk.net) Date: Thu, 17 Oct 2024 20:40:41 +0100 Subject: [Shop-talk] video editor software In-Reply-To: <16a4901db20c4$0fc1f590$2f45e0b0$@gmail.com> References: <1UheSHYA6q.1BGIRYtbzu3.ref@johns-desktop> <1UheSHYA6q.1BGIRYtbzu3@johns-desktop> <16a4901db20c4$0fc1f590$2f45e0b0$@gmail.com> Message-ID: I have done it with the standard issue Photos app in Windows. Run the video, then click the edit button - which for a movie file becomes 'video trim' Neil On 17 October 2024 19:40:37 BST, alfuller194 at gmail.com wrote: >John ? you could try the free VLC video player. It has basic cropping, so you could use it for a 1-off [as opposed to regular use in video editing]. > > > >The program is available here: https://www.videolan.org/vlc/ > > > >Apparently, you have to actually play the video, starting and stopping where you want the crop. While that?s fine for a single video, I wouldn?t want to have to put up with that regularly. I tried it with a .mov someone sent me and it cropped it just fine. > > > >I found a decent guide on using VLC for cropping and other video manipulation here: https://www.videoconverterfactory.com/tips/vlc-video-editor.html > > > >The guides I found wee not clear on where to find the cropped video. It looks like the default location on a Windows PC is the Videos folder, but you could set a different default before you did the cropping. If you are working in Linux or some other OS like the Apple Linux variants, I?m unsure whether the instructions hold. > > > >----------------------------------- > >All the best, > > > >Al Fuller > > > >From: Shop-talk On Behalf Of john niolon >Sent: Thursday, October 17, 2024 4:24 AM >To: shop-talk >Subject: [Shop-talk] video editor software > > > >I made a iPhone video (,mov file) that I need to edit the length... cut out the beginning and end and save the juicy part in the middle > > > >anyone suggest a program/app that works... I tried Canva and Ivideo but never found how to edit that way > > > >shop content... video is made of doing stuff in my shop > >thanks > >john > -- Sent from my Android device with K-9 Mail. Please excuse my brevity. -------------- next part -------------- An HTML attachment was scrubbed... URL: From jniolon at att.net Thu Oct 17 13:54:56 2024 From: jniolon at att.net (john niolon) Date: Thu, 17 Oct 2024 14:54:56 -0500 Subject: [Shop-talk] video editor software In-Reply-To: References: <1UheSHYA6q.1BGIRYtbzu3.ref@johns-desktop> <1UheSHYA6q.1BGIRYtbzu3@johns-desktop> Message-ID: <1UheSNApST.3DrcSmcJlOo@johns-desktop> thanks Lee...never saw that feature...worked like a charm Al, tried that software and it was smarter than me !! but thanks for the suggestion john ----- Original Message ----- From: To: john niolon Cc: shop-talk Sent: 10/17/2024 2:10:18 PM Subject: Re: [Shop-talk] video editor software John - It may depend on which iPhone you have, but on mine (I have both iPhone-11 and - 12), you can crop the ends of the video right there on your phone. Open the video (in Photos), at the top you should see an "Edit" button, that allows sliders (red circle in screen-shot below) at the bottom that you can use to crop from either/both ends. It's a little tricky to activate the sliders - mine is white for just scrolling, but turns yellow (as below) when you've grabbed it for cropping. When you're done, you can overwrite the current video or save it as a new one. I hope this helps! Lee On 2024-10-17 06:23, john niolon wrote: I made a iPhone video (,mov file) that I need to edit the length... cut out the beginning and end and save the juicy part in the middle anyone suggest a program/app that works... I tried Canva and Ivideo but never found how to edit that way shop content... video is made of doing stuff in my shop thanks john _______________________________________________ Shop-talk at autox.team.net Donate: http://www.team.net/donate.html Suggested annual donation $12.96 Archive: http://www.team.net/pipermail/shop-talk http://autox.team.net/archive Unsubscribe/Manage: http://autox.team.net/mailman/options/shop-talk/lee at automate-it.com -------------- next part -------------- An HTML attachment was scrubbed... URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: c99877a7.jpeg Type: image/jpeg Size: 262133 bytes Desc: not available URL: From james.f.juhas at snet.net Thu Oct 17 15:07:54 2024 From: james.f.juhas at snet.net (Jim Juhas) Date: Thu, 17 Oct 2024 17:07:54 -0400 Subject: [Shop-talk] video editor software In-Reply-To: <1UheSNApST.3DrcSmcJlOo@johns-desktop> References: <1UheSNApST.3DrcSmcJlOo@johns-desktop> Message-ID: An HTML attachment was scrubbed... URL: From fishplate at gmail.com Thu Oct 17 18:09:20 2024 From: fishplate at gmail.com (Jeff Scarbrough) Date: Thu, 17 Oct 2024 20:09:20 -0400 Subject: [Shop-talk] Shop/Garage Floor Coating In-Reply-To: References: Message-ID: Thanks to all that replied with advice and experience. I decided to have them add a fine grit. It gets broadcast on the wet floor and is backrolled over before the coating sets. I think it turned out just right - it has some traction, but it can still be easily swept or wiped. None of this was cheap, about $6.75/sq.ft. all in, but it was a quality product installed by people who know what they are doing. I'm OK with that. Some closeups,and a shot of the finished floor: [image: PXL_20241017_192423083.jpg][image: PXL_20241017_192432701.jpg][image: PXL_20241016_192140649.jpg] On Mon, Oct 14, 2024 at 12:02?PM Jeff Scarbrough wrote: > Got a question for the group: > > I'm having my shop floor coated. They are using a polyaspartic coating > after floor prep (surface grinding. My question is related to the finish: > They can leave it as is with the self-leveling (glossyish) finish, or they > can put some grit in it to give it more traction. > > I've had experience in laboratory construction, where the expectation is > that the floor will be washed often and thus wet, so a grit is usually used > to provide traction. But the grit can make mopping more complicated as it > drags the mop. Plus, it just looks funny, like it has dirt on it. > > I can get a number of grit particle sizes and densities, but I keep > wondering if I'll really need it. I plan to keep the floor dry and clean > up any spills as they are made. I won't typically bring in a wet or > snow-covered car. I generally wear shoes in the shop, and my shoes > generally have tread. > > I'd appreciate any insight from those who have coated a floor and gone > smooth or gritty, and how you feel about your choice. > > TIA, > Jeff > -------------- next part -------------- An HTML attachment was scrubbed... URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: PXL_20241017_192423083.jpg Type: image/jpeg Size: 1873192 bytes Desc: not available URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: PXL_20241016_192140649.jpg Type: image/jpeg Size: 2479299 bytes Desc: not available URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: PXL_20241017_192432701.jpg Type: image/jpeg Size: 2088257 bytes Desc: not available URL: From berry at kerch.com Thu Oct 17 18:26:43 2024 From: berry at kerch.com (Berry Kercheval) Date: Thu, 17 Oct 2024 17:26:43 -0700 Subject: [Shop-talk] video editor software In-Reply-To: References: <1UheSNApST.3DrcSmcJlOo@johns-desktop> Message-ID: Sounds like John is set, but if anyone ever wants a full featured studio quality video editor, Da Vinci Resolve?s basic version is free and absurdly capable. Mac and Windows versions available. (If I understand correctly, the Pro version integrates with all the studio hardware: mixing boards, video hardware, etc. The basic one just uses keyboard and mouse.) On Thu, Oct 17, 2024 at 2:12?PM Jim Juhas wrote: > John, > > Realplayer, if on a computer, can trim the beginning and end of a movie > file in its Converter app, part of the free stuff. Also handy for > converting movie files to different formats. Trimming works the same way as > the iPhone editor does. > > Jim > > Sent from my iPhone > > On Oct 17, 2024, at 4:04?PM, john niolon wrote: > > ? > thanks Lee...never saw that feature...worked like a charm > > Al, tried that software and it was smarter than me !! but thanks for the > suggestion > > john > > > > *----- Original Message -----* > *From:* > *To:* john niolon > *Cc:* shop-talk > *Sent:* 10/17/2024 2:10:18 PM > *Subject:* Re: [Shop-talk] video editor software > ------------------------------ > > John - > > It may depend on which iPhone you have, but on mine (I have both iPhone-11 > and -12), you can crop the ends of the video right there on your phone. > Open the video (in Photos), at the top you should see an "Edit" button, > that allows sliders (red circle in screen-shot below) at the bottom that > you can use to crop from either/both ends. It's a little tricky to activate > the sliders - mine is white for just scrolling, but turns yellow (as below) > when you've grabbed it for cropping. When you're done, you can overwrite > the current video or save it as a new one. > > > > > I hope this helps! > > Lee > > > > On 2024-10-17 06:23, john niolon wrote: > > I made a iPhone video (,mov file) that I need to edit the length... cut > out the beginning and end and save the juicy part in the middle > > anyone suggest a program/app that works... I tried Canva and Ivideo but > never found how to edit that way > > shop content... video is made of doing stuff in my shop > thanks > john > > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation $12.96 > Archive: http://www.team.net/pipermail/shop-talk > http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/lee at automate-it.com > > > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation $12.96 > Archive: http://www.team.net/pipermail/shop-talk > http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/james.f.juhas at snet.net > > _______________________________________________ > > Shop-talk at autox.team.net > Donate: http://www.team.net/donate.html > Suggested annual donation $12.96 > Archive: http://www.team.net/pipermail/shop-talk > http://autox.team.net/archive > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/shop-talk/berry at kerch.com > > -------------- next part -------------- An HTML attachment was scrubbed... URL: From james.f.juhas at snet.net Fri Oct 18 16:06:36 2024 From: james.f.juhas at snet.net (Jim Juhas) Date: Fri, 18 Oct 2024 18:06:36 -0400 Subject: [Shop-talk] video editor software In-Reply-To: References: Message-ID: <6FDB0D83-B24B-43FC-8831-F60D7C3187E8@snet.net> An HTML attachment was scrubbed... URL: