[Shop-talk] Winterizing Sprinkler System

[Jim Stone]

The Amazon adaptor arrived yesterday, so I thought I’d update this with some new information.  The adaptor was well made and the shut-off valve proved to be very handy; it was well worth the $20.  It also came with excellent instructions that mostly agreed with what was said here, with one exception: it said “avoid blowing compressed air through the PVB because doing so may damage the BVP.”  I assume my system has a BVP in it, but can’t find it and just went ahead and blew it out from the basement as discussed.

The instructions also recommend that the compressor should be "as large as possible, preferably 15 gallons or larger.”  I think that is good advice, as my little HF 8 gallon compressor was barely (I think) up to the task.  I initially set it to 50 lbs, the recommended pressure, but it was only putting out about 40 lbs during use, so I turned that up to get it a little higher.  Even so, the compressor would fully extend the spray heads for the first 15 seconds or so, then just bubble water out with the head retracted.  The compressor ran constantly while the system was on, so I gave it a rest between blowing out each zone.  I also blew out each zone at least three times, but there was sill some spray at the beginning each time.  I am going to do it one more time today, but know it won’t be completely dry.  I assume it won’t be an issue when the little bit of water remaining in the system freezes, but someone please let me know if I am wrong about this.  My 60 gal compressor is about 150 yards away from the water inlet, but I could make that work if necessary.

Just in time, as the cold weather arrived today, with the first below freezing temps expected tonight.

Cheers,
Jim

> On Nov 5, 2019, at 11:32 AM, Jim Stone <1789alpine at gmail.com> wrote:
> 
> I need to drain and winterize my new sprinkler system and can’t imagine I need to pay someone to do that job.  While I understand the ‘proper’ way to do it is to manually open each valve, I was told a few years ago that it is easier to just pressurize the system at the drain valve and then use the manual function on the controller to run through each zone until no more water comes out.  (FWIW, my system is not that large and has 6 zones.). I was thinking about rigging something up that would allow me to attach my compressor and walk away, but found this on Amazon, which seems like a good investment that would pay for itself on the first use: https://www.amazon.com/Winterize-Sprinkler-Systems-Outdoor-Faucets/dp/B0055QAAIQ/ref=asc_df_B0055QAAIQ/?tag=hyprod-20&linkCode=df0&hvadid=309735714375&hvpos=1o1&hvnetw=g&hvrand=11131050794144962178&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9004590&hvtargid=pla-570302725618&psc=1 <https://www.amazon.com/Winterize-Sprinkler-Systems-Outdoor-Faucets/dp/B0055QAAIQ/ref=asc_df_B0055QAAIQ/?tag=hyprod-20&linkCode=df0&hvadid=309735714375&hvpos=1o1&hvnetw=g&hvrand=11131050794144962178&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9004590&hvtargid=pla-570302725618&psc=1>. I could save around $10 and just buy a hose to quick disconnect fitting, but the shut off valve seems like a good addition.
> 
> I have fairly large compressor, but think it will be more trouble than it is worth to get air to the master drain valve.  Instead, I was planning on just using my Harbor Freight 8 gal portable compressor.  (https://www.harborfreight.com/8-gal-2-hp-125-psi-oil-lube-air-compressor-68740.html <https://www.harborfreight.com/8-gal-2-hp-125-psi-oil-lube-air-compressor-68740.html>).   My water pressure is regulated to 60 lbs, so I figured something around this should be sufficient.
> 
> Am I missing anything?  Is there any good reason to pay a professional to do this job?  It seems like a no-brainer to me, but I’ve been called a no-brainer before.
> 
> Thanks,
> Jim

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/shop-talk/attachments/20191108/c86bd279/attachment.htm>