[Mgs] Silly error.

Thu Jun 13 16:26:08 MDT 2019

Hi Bob. With the covers off and the air dams out, you can clean the jets
with tiny plastic brushes, or even pipe cleaners wetted with spray carb
cleaner. Here's what I use (carefully).

https://www.amazon.com/Brushes-Drinking-Glasses-Keyboards-Cleaning/dp/B073ZCYFY2/ref=sr_1_21_sspa?keywords=Small+plastic+brushes&qid=1560464677&s=gateway&sr=8-21-spons&psc=1

Rick

On Thu, Jun 13, 2019, 5:20 PM Robert's New iPad <mgbobh at gmail.com> wrote:

>    Sunday afternoon is our project day. I want to remove the tops of float
> chambers again, the covers and pistons, and to try a bit of compressed air
> on the jet to see if that will dislodge anything in the passage.  If not,
> we can drop the jets out, but that is awkward on a TF, with its side panels
> diabolically placed to make any carb work difficult.
>    It was this same friend who talked me into a Pertronix for my MGB,
> after he had installed them in this TF and his MGA.   I did, and it
> improved the inaccurate timing quite a bit. A couple of years later, I sent
> the distributor to Advanced Distributors. Jeff wanted to know about the
> engine, its compression, camshaft, porting, polishing, etc, then curved the
> distributor to fit.  This engine runs very well now. Though he is not 100%
> sold on the Pertronix, I keep it because setting dwell of the MGB is not as
> easy as in TD.
>   Fuel, air, spark—we are working to get them all in proper proportion.
> Bob
>
> On Jun 13, 2019, at 4:12 PM, Richard Lindsay <richardolindsay at gmail.com>
> wrote:
>
> Keep cleaning Bob. :-)
>
> My TD and TR3b both had idle instability problems AND the higher speed
> issues. I ended up putting Pertronix distributors in both cars and they ran
> fantastic! The slow idle was perfect.
>
> So check the timing with a timing light to see if it is stable.
>
> On Thu, Jun 13, 2019, 1:51 PM Robert's New iPad <mgbobh at gmail.com> wrote:
>
>>   Good on both of you.
>>   Yesterday was an interesting day for me. Went out as passenger with a
>> friend in his TF, stored a year or so.  It ran out of go at 2500 rpm,
>> sputtering, bucking, etc, but would smooth out at 2000.
>>   Back at the garage, found the strangest stuff in the float chambers.
>> One had a teaspoon of large chunks of solid material. The other had some of
>> that, plus a goo that looked like frog-egg liquid.
>>   The goo was easy enough to figure out, but as the chunks are far larger
>> than would pass through the SU carb banjo filters, the SU pump filter, the
>> additional filter he has in line, and the original screen filter in the
>> tank, it was a puzzle.  We could check banjo, pump and additional
>> filter-none had any grit or sediment.
>>   Pump delivers the pint/minute quantity that workshop manual says.
>>   Engine runs better, but not much. I suspect that some of the sediment
>> is in the passage from float chamber to the jet, but we ran out of day
>> yesterday.
>> Bob
>>
>>
>> On Jun 13, 2019, at 1:49 PM, Richard Lindsay via Mgs <mgs at autox.team.net>
>> wrote:
>>
>>    Good work Hans! I too had a successful day at the shop. I replaced in
>> two bolts in the waterpump housing and the leak is gone! We brought the
>> engine up to temperature with (up to) 13# coolant pressure, and no leaks.
>>    I also found a small fuel leak at the intake of the fuel pump. A
>> couple of spannet twists put that right and dry. With that, we made a few
>> laps around the shop and all was still well.
>>
>> Rick
>>
>> On Thu, Jun 13, 2019, 9:58 AM Hans Duinhoven <h.duinhoven at planet.nl>
>> wrote:
>>
>>> Funny – I solved coolant issues earlier and yesterday.
>>>
>>> Had to replace the thermostat housing gasket and yesterday I had to
>>> replace the hose connecting the bottom radiator pipe to the waterpump.
>>>
>>> A horrible job to do, as there is almost no space to work at the bottom
>>> of the radiator pipe.
>>>
>>> Nut with a dry result!
>>>
>>>
>>>
>>> Fully cleaned a clogged charcoal filter and renewed the charcoal
>>> particles.
>>>
>>> Replaced the oil filler cap and will renew the brake fluid tomorrow.
>>>
>>> Then the GT should be roadworthy again.
>>>
>>>
>>>
>>> Cheers,
>>>
>>> Hans
>>>
>>> 71 BGT NRG -
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>> *Van:* Mgs [mailto:mgs-bounces at autox.team.net] *Namens *Richard Lindsay
>>> via Mgs
>>> *Verzonden:* woensdag 12 juni 2019 18:51
>>> *Aan:* mgs at autox.team.net List
>>> *Onderwerp:* [Mgs] Silly error.
>>>
>>>
>>>
>>> Hi Friends,
>>>
>>>    My TR6 rebuilt engine leaks coolant. Okay, its not an MG but the
>>> issue is universal. Here's the short story.
>>>
>>>    When reassembling the waterpump I made a newbie error. I got in a
>>> hurry and left out two bolts, some of the bolts that hold the pump body to
>>> the head. The coolant leak is through one of those bolt holes. The threaded
>>> hole drilling entered the head's water jacket and of course, leaks.
>>>
>>>    I now have new bolts and I will apply sealant to the threads and
>>> place fiber sealing washers under the bolt heads. Doing so hopefully
>>> completes the engine rebuild. I can then get back to replacing the top on
>>> my MG TD.
>>>
>>>
>>>
>>> Rick
>>>
>>>
>>> <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virusvrij.
>>> www.avast.com
>>> <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
>>> <#m_4813474141780684756_m_-737199480811640730_m_-2666518911097195659_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
>>>
>> _______________________________________________
>>
>> Mgs at autox.team.net
>> Donate: http://www.team.net/donate.html
>> Suggested annual donation  $12.75
>>
>> Archive: http://www.team.net/pipermail/mgs http://autox.team.net/archive
>>
>> Unsubscribe: http://autox.team.net/mailman/options/mgs/mgbobh@gmail.com
>>
>>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/mgs/attachments/20190613/4e93b59e/attachment.html>