[Mg-t] TD top radiator hose replacement

[Lew Palmer]

Next time, try this hose:
http://www.pegasusautoracing.com/productdetails.asp?RecID=4661

Cheers,
Lew Palmer

-----Original Message-----
From: mg-t-bounces at autox.team.net [mailto:mg-t-bounces at autox.team.net] On
Behalf Of Bob Donahue
Sent: Saturday, August 28, 2010 11:59 AM
To: Mg-t at autox.team.net
Subject: Re: [Mg-t] TD top radiator hose replacement

Thanks for the tip. I managed to get the hose on with the help of a small 
nail prying tool last night. It took a lot of prying and twisting, but I 
finally got it on. Forcing the hose to compress, like that, must have put a 
lot of pressure against the radiator and the thermostat housing. I'm lucky 
nothing broke! I'm sure shortening the hose would have helped immensely.

BTW, I wonder if there is a more flexible replacement that could be had from

some source? The reproduction hose is so heavy duty, I bet it could hold 200

lbs of pressure. (And our radiator pressure is zero!)

Bob Donahue (Still Stuck in the '50s)
Email - bobmgtd at comcast.net
Cars:       52 MGTD - #17639
               71 MGB - #GHN5UB254361
Member:  NEMGTR #11470
               NAMGBR # 7-3336
               Hoosier MGB Club
               Olde Octagons of Indiana

----- Original Message ----- 
From: "John Seim" <kingseim at earthlink.net>
To: "Bob Donahue" <bobmgtd at comcast.net>
Cc: <Mg-t at autox.team.net>
Sent: Saturday, August 28, 2010 9:00 AM
Subject: Re: [Mg-t] TD top radiator hose replacement


> Bob, seeing how you have the radiator installed, and want to just  replace

> the radiator hose.
> They are now too stiff to install. The bump in the hose, aka bumped  hose,

> was supposed to
> be a flex joint. This would allow for the matching up of the engine  water

> outlet angle and the
> radiator top tank tube angle to be different (which they are), and  the 
> flex joint to move.
>
> Since the hose is too stiff now, you can cut off say 1/4" from each  end 
> of the hose. That should
> shorten it enough to install in situ.
>
> John Seim
> Irvine, CA
>
> On Aug 27, 2010, at 4:30 PM, Bob Donahue wrote:
>
>> What is the correct procedure for installing a new top radiator  hose on 
>> a TD?
>> Is there anyway of doing it without removing the thermostat  housing? (My

>> new
>> reproduction hose is much too stiff to squish it on. I think I was  able 
>> to do
>> this with an old hose.)
>>
>> Bob Donahue (Still Stuck in the '50s)
>> Email - bobmgtd at comcast.net
>> Cars:       52 MGTD - #17639
>>                71 MGB - #GHN5UB254361
>> Member:  NEMGTR #11470
>>                NAMGBR # 7-3336
>>                Hoosier MGB Club
>>                Olde Octagons of Indiana
______________________________________________

Mg-t at autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation  $11.47
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/mg-t/lpalmer@roundaboutmanor.com