<html><body>John- it is a .040 feeler gauge that goes under the throttle stop- That is equivalent to about 1/5 throttle opening. That is to set the throttle switch. <div><br></div><div>The 3/16 drill bit is used to "static set" the position of the solenoid lever. I agree, that position is not alway ideal. Fine adjustment is made at the arm of the solenoid in which you get it to the maximum lift and then when it drops it clears the base about 1/32" at the same time gently pushing it in toward the casing to make sure it does not bind. Solenoid plunger must drop freely. I can send you that page from Haynes manual if it helps you to set the throttle switch. Hank<br><div class="reply-new-signature"></div><p>-----------------------------------------</p>From: "John Spaur" <jmsdarch@sbcglobal.net><br>To: "Hank Leach", "Bob Spidell"<br>Cc: healeys@autox.team.net<br>Sent: Sunday July 2 2023 6:01:07PM<br>Subject: RE: [Healeys] Overdrive disengages<br><br>
<div class="WordSection1">
<p class="MsoNormal"><span style="font-size:11pt;font-family:Calibri, sans-serif;color:#1F497D;">I
think I understand now.</span></p>
<p class="MsoNormal"><span style="font-size:11pt;font-family:Calibri, sans-serif;color:#1F497D;"> </span></p>
<p class="MsoNormal"><span style="font-size:11pt;font-family:Calibri, sans-serif;color:#1F497D;">I
need to loosen the arm on the throttle switch, put a 3/16 spacer
under the throttle stop and adjust the throttle switch so the test
light goes out and then tighten everything up.</span></p>
<p class="MsoNormal"><span style="font-size:11pt;font-family:Calibri, sans-serif;color:#1F497D;"> </span></p>
<p class="MsoNormal"><span style="font-size:11pt;font-family:Calibri, sans-serif;color:#1F497D;">Correct?</span></p>
<p class="MsoNormal"><span style="font-size:11pt;font-family:Calibri, sans-serif;color:#1F497D;"> </span></p>
<p class="MsoNormal"><span style="font-size:11pt;font-family:Calibri, sans-serif;color:#1F497D;">-john</span></p>
<p class="MsoNormal"><span style="font-size:11pt;font-family:Calibri, sans-serif;color:#1F497D;"> </span></p>
<div>
<div style="border:none;border-top:solid #E1E1E1 1pt;padding:3pt 0in 0in 0in;">
<p class="MsoNormal"><b><span style="font-size:11pt;font-family:Calibri, sans-serif;">From:</span></b>
<span style="font-size:11pt;font-family:Calibri, sans-serif;">Healeys
[mailto:healeys-bounces@autox.team.net] <b>On Behalf Of</b> Hank
Leach via Healeys<br><b>Sent:</b> Sunday, July 2, 2023 10:24 AM<br><b>To:</b> 'Bob Spidell' <bspidell@comcast.net><br><b>Cc:</b> healeys@autox.team.net<br><b>Subject:</b> Re: [Healeys] Overdrive disengages</span></p>
</div>
</div>
<p class="MsoNormal"> </p>
<p class="MsoNormal" style="margin-bottom:12pt;">Bob's got the
procedure. Use a .040" feeler gauge (or 3/16 drill) under the
throttle stop (1/5 of the throttle opening). Connect a 12V
test light to the fuse box and the top terminal on the throttle
switch. (Good example in Haynes Manual page 124). Light should go
out at this adjustment. Solenoid adjustment should be as Bob
describes and work smoothly-no binding. Hank</p>
<p>-----------------------------------------</p>
<p class="MsoNormal" style="margin-bottom:12pt;">From: "Bob
Spidell"<br>
To: <a>healeys@autox.team.net</a><br>
Cc:<br>
Sent: Sunday July 2 2023 9:20:10AM<br>
Subject: Re: [Healeys] Overdrive disengages<br><br>
Hi John,<br><br>
What keeps the O/D from disengaging immediately when you open the
dash switch is the 'throttle switch.' When the O/D is actuated
there is a parallel circuit that will keep the O/D activated until
you press the accelerator pedal, theoretically preventing reverse
thrust from damaging the O/D. The parallel circuit runs through the
throttle switch on the scuttle (firewall); it sounds like you need
to adjust it. It's a simple adjustment using a certain diameter--I
don't recall it offhand, but I'll look it up if you need it--drill
bit under the throttle stop levers. There's a small shaft off the
throttle mechanism that opens this switch--it's just a set of
points and a cam inside--with a lever with a pinch clamp. Just
loosen the pinch clamp, set the bit under the throttle stop plate
and tighten the clamp.<br><br>
If you O/D is actuating consistently within a couple seconds or so
then your solenoid, operating lever, operating shaft and ball
'valve' are correct. The
'stick-a-drill-bit-through-the-lever-into-the-housing' method is
notoriously unreliable; the proper setting is best achieved by
measuring the lift--IIRC, it's 1/32" but not sure--of the operating
shaft at the top of the O/D hydraulic section.<br><br>
Bob<br><br></p>
<div>
<p class="MsoNormal">On 7/1/2023 11:55 AM, John Spaur via Healeys
wrote:</p>
</div>
<blockquote style="margin-top:5pt;margin-bottom:5pt;">
<div>
<p class="MsoNormal">Hi All,</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">My overdrive
is functioning again after replacing the accumulator housing and
piston but it is exhibiting an odd behavior which I believe is
related to the adjustment of the setting lever.</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">When I open
the toggle switch, the OD will sometimes disengage immediately
instead of waiting until I blip the accelerator. When I adjusted
the setting lever, I could not use a 3/16” dowel to line up the
lever with the hole in the housing. I had to advance the lever
clockwise a bit to get the OD to engage when the toggle switch was
closed. This has always been the case and this issue is mentioned
in some articles.</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">Do I need to
fiddle with the setting lever adjustment some more? If so, do I
rotate it clockwise or counter clockwise?</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">Any other
thoughts?</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">TIA,</p>
<p class="MsoNormal">John Spaur</p>
<p class="MsoNormal">’62 BT7</p>
</div>
<p class="MsoNormal"> </p>
</blockquote>
<p class="MsoNormal"><br><br></p>
</div>
</jmsdarch@sbcglobal.net></div></body></html>