<html><body>Be sure that the 8 (4 of each size) springs are correctly placed or they will be coil bound and resist assembly. See photo. Hank<br><br><div class="reply-new-signature"></div><p>-----------------------------------------</p>From: "warthodson--- via Healeys" <healeys@autox.team.net><br>To: "Bob Spidell", "Michael Salter"<br>Cc: "healeys@autox.team.net"<br>Sent: Tuesday June 20 2023 9:15:12AM<br>Subject: Re: [Healeys] Mating the overdrive to the transmission<br><br>
<div class="ydp497b91c3yahoo-style-wrap" style="font-family:'Comic Sans MS', sans-serif;font-size:16px;">
<div dir="ltr">Michael,</div>
<div dir="ltr">We do have a spare trans output
shaft & we have watched your video & made a wire tool to retract
the pump plunger. We have verified that the plunger is fully
retracted & the splines are aligned. The spare shaft goes in about
1/2" (all the way in) further than the one that came out of the
car. </div>
<div dir="ltr">Gary</div>
<div><br></div>
</div>
<div class="ydpd0cdbba8yahoo_quoted">
<div style="font-family:'Helvetica Neue', Helvetica, Arial, sans-serif;font-size:13px;color:#26282a;">
<div>On Tuesday, June 20, 2023 at 07:12:20 AM CDT, Michael Salter
<michaelsalter@gmail.com> wrote:</div>
<div><br></div>
<div><br></div>
<div>
<div>
<div>
<div>Although one may be difficult to find there is no substitute
for a spare gearbox 3rd motion shaft for this job.
<div>The spare shaft is used to align all the internals then, using
my special tool to hold the pump plunger retracted</div>
<div><a href="https://precisionsportscar.com/laycock-de-normanville-overdrive-installation-tool/"></a><a href="https://precisionsportscar.com/laycock-de-normanville-overdrive-installation-tool/">https://precisionsportscar.com/laycock-de-normanville-overdrive-installation-tool/</a></div>
<div> it is a simple task to lower the overdrive onto the
gearbox. </div>
<div><br clear="none"></div>
<div>M</div>
</div>
<br clear="none"><div class="ydpd0cdbba8yiv8503291482gmail_quote">
<div class="ydpd0cdbba8yiv8503291482yqt3152633389">
<div dir="ltr" class="ydpd0cdbba8yiv8503291482gmail_attr">On Mon.,
Jun. 19, 2023, 11:41 p.m. Bob Spidell, <<a>bspidell@comcast.net</a>> wrote:<br clear="none"></div>
<blockquote style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;" class="ydpd0cdbba8yiv8503291482gmail_quote">
<div>There is a bronze thrust washer that has to be perfectly
centered to get that last 3/4" (#148 in this diagram):<br clear="none"><br clear="none"><a href="https://mossmotors.com/ahy-041-overdrive-unit-bn2-thru-bj8"></a><a href="https://mossmotors.com/ahy-041-overdrive-unit-bn2-thru-bj8">https://mossmotors.com/ahy-041-overdrive-unit-bn2-thru-bj8</a><br clear="none"><br clear="none">
You can wiggle it around with a long screwdriver, or use a suitable
'drift' to center it. Your best bet is to sit the O/D on end and
lower the gearbox onto it; gently rotating the gearbox while
lowering. First time I did this I must have got lucky, but danged
if I can explain this (see attached photo). Most recently I fought
for a couple days then threw in the towel and took gearbox and O/D
to BCS which, fortunately, is only a half-hour away. David and his
mechanics had a novel technique I've not heard described anywhere;
basically, he removed the pump completely--it's only two screws
IIRC--and split the O/D into front and rear sections and tipped the
gearbox and O/D up--gearbox on bottom--then had two of his
mechanics pull the sections together with huge channellock pliers
while David rotated the output shaft to 'feel it in' (you had to be
there).<br clear="none"><br clear="none">
Good luck. Make triply sure you have the pump cam oriented
correctly, or you'll get more experience with this process than you
probably want.<br clear="none"><br clear="none">
bs<br clear="none"><br clear="none"><div>On 6/19/2023 6:18 PM, warthodson--- via Healeys
wrote:<br clear="none"></div>
<blockquote>
<div style="font-family:'Comic Sans MS', sans-serif;font-size:16px;">
<div dir="ltr">I spent the day assisting a friend trying to mate
his OD to his transmission. The car is a '63 BJ7. The overdrive &
Trans. were pulled to replace a few internal trans parts which was
done & we did not run into any issues. We can get the OD to within
approx. 1/2-3/4" of mating to the trans, but cannot close that gap.
We have confirmed that the oil pump roller has been fully
retracted. What are we bumping up against & how do we get past
it?</div>
<div dir="ltr">Gary Hodson</div>
</div>
<br clear="none"></blockquote>
<br clear="none"></div>
_______________________________________________<br clear="none">
Support Team.Net <a href="http://www.team.net/donate.html"></a><a href="http://www.team.net/donate.html">http://www.team.net/donate.html</a><br clear="none">
Suggested annual donation $12.75<br clear="none"><br clear="none">
Archive: <a href="http://www.team.net/pipermail/healeys"></a><a href="http://www.team.net/pipermail/healeys">http://www.team.net/pipermail/healeys</a> <a href="http://autox.team.net/archive/healeys"></a><a href="http://autox.team.net/archive/healeys">http://autox.team.net/archive/healeys</a><br clear="none"><br clear="none"><a>Healeys@autox.team.net</a><br clear="none"><a href="http://autox.team.net/mailman/listinfo/healeys"></a><a href="http://autox.team.net/mailman/listinfo/healeys">http://autox.team.net/mailman/listinfo/healeys</a><br clear="none"><br clear="none">
Unsubscribe/Manage: <a href="http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com"></a><a href="http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com">http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com</a><br clear="none"><br clear="none"></blockquote>
</div>
</div>
</div>
</div>
<div class="ydpd0cdbba8yqt3152633389">
_______________________________________________<br clear="none">
Support Team.Net <a href="http://www.team.net/donate.html"></a><a href="http://www.team.net/donate.html">http://www.team.net/donate.html</a><br clear="none">
Suggested annual donation $12.75<br clear="none"><br clear="none">
Archive: <a href="http://www.team.net/pipermail/healeys"></a><a href="http://www.team.net/pipermail/healeys">http://www.team.net/pipermail/healeys</a> <a href="http://autox.team.net/archive/healeys"></a><a href="http://autox.team.net/archive/healeys">http://autox.team.net/archive/healeys</a><br clear="none"><br clear="none"><a>Healeys@autox.team.net</a><br clear="none"><a href="http://autox.team.net/mailman/listinfo/healeys"></a><a href="http://autox.team.net/mailman/listinfo/healeys">http://autox.team.net/mailman/listinfo/healeys</a><br clear="none"><br clear="none">
Unsubscribe/Manage: <a href="http://autox.team.net/mailman/options/healeys/warthodson@aol.com"></a><a href="http://autox.team.net/mailman/options/healeys/warthodson@aol.com">http://autox.team.net/mailman/options/healeys/warthodson@aol.com</a><br clear="none"><br clear="none"></div>
</div>
</div>
</div>
</healeys@autox.team.net></body></html>