<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body>
Something to consider, which might be germane: <br>
<br>
My dad and I rebuilt our BN2's engine, having the head done by a
pro. When we reassembled the drivetrain, I put a good, thick coat of
Moss's 'Healey Engine Green' on all parts, painting the engine and
gearbox/OD separately. Once we got the drivetrain in the car, and at
least had a 'running' chassis I would drive it short distances, then
the car was put on hold while Dad endured throat cancer treatment.
I'm not sure when the problem started, but at some point the car
became difficult to start at times; sometimes it would start right
up--though I did think it cranked a bit slow--and others it would
barely turn over, if at all. We charged the batteries
repeatedly--one time Dad cross-wired the jumpers somehow and
actually got a hydrogen gas explosion, only sheepishly only
admitting 'It needed new batteries' (I got the whole story
later)--but there was no improvement. Dad suspected we didn't have
good connections on the battery/starter cable; we had to use
oxy/acetylene to get what appeared to be good solder connections
but, eventually, after Dad died, I pulled the starter and sent it to
Mike Martinez at Star Auto Electric for a rebuild, but that didn't
help either. My thinking on fasteners keeps evolving, but when I'd
first fitted the starter to the engine backplate I'd used grade 8
flat washers under split washers, but at some point I decided to
just use the split washers and, to my amazement it's cranked
beautifully since then. Apparently, the thick coat of paint under
the flat washers created enough resistance to hinder starter
operation, and the sharp ends of the split washers pierced the paint
and gave good ground. It's not surprising you can't move the starter
ring much, if you're on the bottom of a compression stroke.<br>
<br>
TL;DR: check all your grounds. You might have some unseen corrosion
from sitting.<br>
<br>
Bob<br>
<br>
<div class="moz-cite-prefix">On 5/22/2022 4:26 AM, Patrick &
Caroline Quinn via Healeys wrote:<br>
</div>
<blockquote type="cite"
cite="mid:007201d86dce$cc6596d0$6530c470$@tpg.com.au">
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
<meta name="Generator" content="Microsoft Word 15 (filtered
medium)">
<style>@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0cm;
font-size:11.0pt;
font-family:"Calibri",sans-serif;
mso-fareast-language:EN-US;}span.EmailStyle17
{mso-style-type:personal-compose;
font-family:"Calibri",sans-serif;
color:windowtext;}.MsoChpDefault
{mso-style-type:export-only;
font-family:"Calibri",sans-serif;
mso-fareast-language:EN-US;}div.WordSection1
{page:WordSection1;}</style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext="edit" spidmax="1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext="edit">
<o:idmap v:ext="edit" data="1" />
</o:shapelayout></xml><![endif]-->
<div class="WordSection1">
<p class="MsoNormal">Hello<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">A problem to consider.<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">Went to turn the engine over in the BN3. An
early C-Series six-cylinder. Rebuilt about five years back,
but seen next to no use.<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">Solenoid clicks, but no movement from the
engine. Must be the battery so charged it, but no change.
Tried a brand new battery, but still no movement.<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">Out comes the starter and connect it
straight to the battery. Whirr away on the floor. Perhaps the
original Lucas starter is breaking down under load?<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">It occurs to me to try and turn the engine
over by hand. Gearbox tunnels not fitted so easy to wield a
large screwdriver to leaver the flywheel, after removing the
spark plugs. It moves about six teeth of the ring gear, but no
more. It moves back the same in the other direction, but no
further. Soon lose interest in this manoeuvre. <o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">What’s up? Why won’t the engine turn over?
Thinking cap on and perhaps it’s something at the top of the
engine such as valve gear. Perhaps there is a bent valve?<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">Any opinions out there?<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">Many thanks<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">Patrick Quinn<o:p></o:p></p>
<p class="MsoNormal">Blue Mountains, Australia<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
</div>
<br>
</blockquote>
<br>
</body>
</html>