<html>
  <head>
    <meta http-equiv="Content-Type" content="text/html;
      charset=windows-1252">
  </head>
  <body>
    Not concours, but when I did my BN2's doors I lined them with a thin
    insulator, basically thin 'bubble wrap' with foil on either side.
    IIRC, I did this because I didn't want just vinyl against metal, but
    was pleasantly surprised when it caused the doors to make a
    satisfying 'thunk' on closing; the best-sounding doors I've ever
    heard (at least on a Healey). I tried to make a video with sound,
    but the recording didn't do them justice.<br>
    <br>
    <br>
    <div class="moz-cite-prefix">On 10/1/2021 6:39 AM, S and T Miller
      via Healeys wrote:<br>
    </div>
    <blockquote type="cite"
cite="mid:BL0PR04MB4881F1066A6B2A843B3189DDD4AB9@BL0PR04MB4881.namprd04.prod.outlook.com">
      <meta http-equiv="Content-Type" content="text/html;
        charset=windows-1252">
      <div style="font-family: "segoe ui westeuropean",
        "segoe ui", helvetica, arial, sans-serif; font-size:
        12pt; color: rgb(0, 0, 0);">
        I've done some more digging on the "Ole interwebs" after asking
        this question of the group.  I did learn that not all doors have
        the vertical/ central wide metal brace running from the bottom
        of the door to the wood horizontal brace (screw attachment point
        for the upper panel). I'd speculate that it was added on later
        in the run as a needed exterior door skin support. I'm sure
        someone on here knows when and why. I did find some pictures
        showing the vinyl glued over that brace and it is visible
        through the vinyl covering. </div>
      <div style="font-family: "segoe ui westeuropean",
        "segoe ui", helvetica, arial, sans-serif; font-size:
        12pt; color: rgb(0, 0, 0);">
        <br>
      </div>
      <div style="font-family: "segoe ui westeuropean",
        "segoe ui", helvetica, arial, sans-serif; font-size:
        12pt; color: rgb(0, 0, 0);">
        As far as the wood horizontal brace it appears most glue it
        creating a 90 degree lip below the upper stiff backed panel. It
        just didn't seem correct to me, but after viewing numerous
        completed cars,  it doesn't look bad.  </div>
      <div style="font-family: "segoe ui westeuropean",
        "segoe ui", helvetica, arial, sans-serif; font-size:
        12pt; color: rgb(0, 0, 0);">
        <br>
      </div>
      <div style="font-family: "segoe ui westeuropean",
        "segoe ui", helvetica, arial, sans-serif; font-size:
        12pt; color: rgb(0, 0, 0);">
        I'm not doing a concours car, but some areas I just get all
        wrapped up in making it as factory correct as possible.  </div>
      <div><br>
      </div>
      <div><br>
      </div>
      <div>The Millers<br>
         <br>
        "Always drive them, but remember each drive in an antique car is
        a test drive."<br>
      </div>
      <div><br>
      </div>
      <hr style="display:inline-block;width:98%" tabindex="-1">
      <div id="divRplyFwdMsg" dir="ltr"><font style="font-size:11pt"
          face="Calibri, sans-serif" color="#000000"><b>From:</b> S and
          T Miller<br>
          <b>Sent:</b> Wednesday, September 29, 2021 9:02 PM<br>
          <b>To:</b> <a class="moz-txt-link-abbreviated" href="mailto:healeys@autox.team.net">healeys@autox.team.net</a>
          <a class="moz-txt-link-rfc2396E" href="mailto:healeys@autox.team.net"><healeys@autox.team.net></a><br>
          <b>Subject:</b> 100 door vinyl original glue technique </font>
        <div> </div>
      </div>
      <div>
        <div style="font-family:"segoe ui
          westeuropean","segoe
          ui",helvetica,arial,sans-serif; font-size:12pt;
          color:rgb(0,0,0)">
          How did the factory go about gluing the bottom inner vinyl
          material to the inner door? So if you glue it tight there is a
          brace running up the middle that will show through, and also
          there would be a 90 degree ledge where it meets the horizontal
          wood middle support (below the upper vinyl covered panel). I'm
          fairly certain there was no backing material on this piece of
          vinyl from the factory.  My thought is to glue to the metal
          brace and glue a distance away to create a nice transition.
          And the same method from the horizontal mid wood support which
          would leave some unglued void areas between the vinyl and the
          inner door. </div>
        <div style="font-family:"segoe ui
          westeuropean","segoe
          ui",helvetica,arial,sans-serif; font-size:12pt;
          color:rgb(0,0,0)">
          <br>
        </div>
        <div style="font-family:"segoe ui
          westeuropean","segoe
          ui",helvetica,arial,sans-serif; font-size:12pt;
          color:rgb(0,0,0)">
          I do realize that adding some backing takes care of the
          issues,  but am interested in how it was done originally.  I
          don't recall mine having any backing, and my original vinyl is
          too stiff and pulled away to tell how it was done. Once I
          flattened out my originals,  they did make fantastic templates
          to cut the new vinyl from. </div>
        <div style="font-family:"segoe ui
          westeuropean","segoe
          ui",helvetica,arial,sans-serif; font-size:12pt;
          color:rgb(0,0,0)">
          TIA, Shawn</div>
        <div><br>
        </div>
        <div>The Millers<br>
           <br>
          "Always drive them, but remember each drive in an antique car
          is a test drive."<br>
        </div>
      </div>
      <br>
    </blockquote>
    <br>
  </body>
</html>