<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:m="http://schemas.microsoft.com/office/2004/12/omml" xmlns="http://www.w3.org/TR/REC-html40"><head><meta http-equiv=Content-Type content="text/html; charset=utf-8"><meta name=Generator content="Microsoft Word 15 (filtered medium)"><style><!--
/* Font Definitions */
@font-face
        {font-family:"Cambria Math";
        panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
        {font-family:Calibri;
        panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
        {margin:0cm;
        font-size:11.0pt;
        font-family:"Calibri",sans-serif;}
span.EmailStyle19
        {mso-style-type:personal-reply;
        font-family:"Calibri",sans-serif;
        color:windowtext;}
.MsoChpDefault
        {mso-style-type:export-only;
        font-size:10.0pt;}
@page WordSection1
        {size:612.0pt 792.0pt;
        margin:72.0pt 72.0pt 72.0pt 72.0pt;}
div.WordSection1
        {page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext="edit" spidmax="1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext="edit">
<o:idmap v:ext="edit" data="1" />
</o:shapelayout></xml><![endif]--></head><body lang=EN-CA link=blue vlink=purple style='word-wrap:break-word'><div class=WordSection1><p class=MsoNormal><span style='mso-fareast-language:EN-US'>Simon, you seemed to have covered all the bases.  Again respectfully, how are so sure that nothing is binding on the pilot bush?  I am not sure the best way to check it but if possible, if you can remove it and actually slide it onto the output shaft on the g’box, that would be best.  If the bush is firmly in there (and it usually is!), I suggest you might offer up the gearbox to the engine <u>without</u> the clutch in place and see if it slides in easily and that you can get the bell housing all the way up to the rear engine plate.  That is a lot more work, but would absolutely rule out any issue with the pilot bush. <o:p></o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'>I assume that the throw bearing is in good shape and moves easily in the fork of the clutch arm.  I am grasping at straws now!<o:p></o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'>As others have said, I spend a lot of time checking the gap between the bell housing and the engine plate when I am putting a g’box back to ensure it is even all the way around and the g’box goes in perfectly square.<o:p></o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'>Wish I were closer, I’d gladly lend a hand.<o:p></o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'>I just have a few last things to put back on my motor and Michael and I are going to start it up after a fresh rebuild, hopefully Wednesday.<o:p></o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'>Cheers, Mirek<o:p></o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><div><div style='border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0cm 0cm 0cm'><p class=MsoNormal><b><span lang=EN-US>From:</span></b><span lang=EN-US> simon.lachlan@alexarevel.plus.com <simon.lachlan@alexarevel.plus.com> <br><b>Sent:</b> September 27, 2021 8:43 AM<br><b>To:</b> 'richard mayor' <boyracer466@gmail.com><br><b>Cc:</b> m.g.sharp@sympatico.ca; 'Healeys' <healeys@autox.team.net><br><b>Subject:</b> RE: [Healeys] New Clutch query<o:p></o:p></span></p></div></div><p class=MsoNormal><o:p> </o:p></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>Thank you everybody for your replies. <o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>Richard’s advice as to centering the clutch by moving the alignment tool back and forth, up/down seems very sensible and I’ll try that.<o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>I said that I thought the black plastic alignment tool was easier to use than the shaft because, with plastic tool, one can plug the clutch plate to the flywheel then wind on the cover as no part of the tool is wider than the hole in the centre of the cover. With the shaft, one has to put it through cover and clutch plate and then fight the pair up and onto the flywheel. <o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>Two people found (very!) polite ways of asking if I’d put the clutch plate on backwards. Sadly not; that might have produced an instant cure. I’m way past being offended by such questions. <o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>Nothing is binding in the spigot bush/pilot bearing. Another instant cure missed.<o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>No slop in the  clutch lever bushings. The slave’s push rod and clevis pin were in a bad way although that had not  -   previously – impinged. I’ve ordered new ones anyhow.<o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>I’ve got the two dowel bolts and used them at 11:00 and 17:30. (Incidentally, I’ve got on file an email, 11 June ’02, of Michael’s in which he makes reference to the importance attached to these bolts as a “tempest in a teapot”. His maths makes perfect sense, as you’d expect, but I’ll be sure to put them in per the book).<o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>I did have a jack under the engine and will again. <o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>Barring anything new received from you guys, I’ll just have to try again, paying great attention to the plate being centred and the engine/gearbox being at compatible angles.<o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>No attempt today as son-in-law is at work! It is definitely a task where an Arnie-lookalike is extremely useful.<o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'>Simon<o:p></o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span lang=EN-GB style='mso-fareast-language:EN-US'><o:p> </o:p></span></p></div></body></html>