<html><body>Michael- Based on the price of them, they are probably ready to use. You can tell by how much wheel weight is required to have them run true. 1-2 oz. good; 4-6 oz. or higher, you might have to check them for runout. You can always mount one on a hub and spin it with a dial gauge fixed somewhere- over .030" runout and they are in need of truing. Hank<br><br><div class="reply-new-signature"></div><p>-----------------------------------------</p>From: "Michael MacLean" <springer.mike51@gmail.com><br>To: "Ahealey help"<br>Cc: <br>Sent: Monday May 3 2021 1:42:17PM<br>Subject: Re: [Healeys] Spokes and Truing Wheels<br><br>
<div>I have brand new Daytons on my BN2. Not used
yet at this point. Should they be tried OK from the factory?
<div>Mike MacLean</div>
</div>
<br><div class="gmail_quote">
<div dir="ltr" class="gmail_attr">On Mon, May 3, 2021, 12:24 PM
Henry G Leach via Healeys <<a>healeys@autox.team.net</a>>
wrote:<br></div>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;">
<div>As a kid with no money, in the early '70, I thought it would
be great to have chrome wire wheels on the finished example of the
A-H100 that I had just disassembled. They would just look like
Donald Healey's show cars.
<div><br></div>
<div>So, I took the wheels I had, picked up some additional used
wheels, including one new affordable one I located, and
disassembled all of them, breaking lots of spokes as I went
along..until I eventually had enough good spokes and nibs for 5
wheels. Remember this was the 1970s so parts for these cars
were nil and so was the money to buy new chrome ones. The only
affordable thing at that time was chrome plating. I had 5 wheels
and hubs and countless spokes and nibs re-plated for $150!</div>
<div><br></div>
<div>I polished all the spokes and nibs in a hobby rock tumbler
used to shine beach rocks to gemlike appearance...took hours and
days but not $$. The chrome plater assured me he would "anneal" the
spokes so as not to get brittle in the process</div>
<div><br></div>
<div>Forty-five years later they are on the car after spending
hours assembling and truing. Was all that worth the effort, that
now you can just order an Indian set from Moss for a grand? I
don't know if a labor of love counts in this case, but I get lots
of positive comments on the finished "affordable" product. Hank<br><br><p>-----------------------------------------</p>
From: "Laurie Wilford"<br>
To: "<a>gradea1@charter.net</a>", "Harold Manifold"<br>
Cc: "<a>healeys@autox.team.net</a>"<br>
Sent: Monday May 3 2021 11:20:06AM<br>
Subject: RE: [Healeys] Spokes and Truing Wheels<br><br><div>I have rebuilt and trued a number of wire wheels over the past
thirty years, starting with replacing spokes on my Made in
India Dunlop chrome 60 spoke set. </div>
<div>I broke so many spokes on those wheels that I ended up
purchasing spokes and nipples in bulk direct from
Dayton.</div>
<div>The information I was given by them was that truing wheels to
plus or minus 0.030" was the best they could expect when building
new wheels!</div>
<div><br></div>
<div>Laurie Wilford </div>
<div><br></div>
<div>
<div style="font-size:85%;color:#575757;">Sent from my Galaxy</div>
</div>
<div><br></div>
<div><br></div>
<div><br></div>
<div>-------- Original message --------</div>
<div>From: Henry G Leach via Healeys <<a>healeys@autox.team.net</a>></div>
<div>Date: 2021-05-03 1:40 p.m. (GMT-05:00)</div>
<div>To: 'Harold Manifold' <<a>manifold@telus.net</a>></div>
<div>Cc: "'<a>healeys@autox.team.net</a>'" <<a>healeys@autox.team.net</a>></div>
<div>Subject: Re: [Healeys] Spokes and Truing Wheels</div>
<div><br></div>
<div>Hi Harold- yes, I also used a dial gauge and that,
unfortunately, is too fine an instrument for the crude wheels that
we have. It will drive you crazy to try to "0" out the wheel. Looks
like you got close and could not effect a change. Me too.
That is probably as good as it will get. I think the eye is a
better judge of the "quality" of the wheel-if you see runout try to
move it to be less. Of the five wheels I did I rated them as the
best-worse and used #5 for the spare, putting the best on the
fronts. They are very close to "good" as round goes. A wonderful
theory that in practical use has some forgiveness.
<div><br></div>
<div>You could send them assembled, off to Hendricks Wheel service
and they may be able to do a tighter finish. Folks swear that
their trued, shaved, rebuilt wheels from them are the cats
meow.</div>
<div><br></div>
<div>A couple of things I did in assembly: I used anti seize
compound on all the spoke threads-just enough to make so you could
possibly undo them later. Then at the other end, I used marine
sealant on the hub nubs to seal in grease and seal out water.
May work for awhile. I also ran a 2" duct tape seal over the nibs
in the rim, in addition to the rubber rim seal (which does not
cover them well.)</div>
<div><br></div>
<div>The only secret sequence I found was when you tightened one
nib, you needed to go to the exact opposite nib to compensate for
the "pull" on the shape of the wheel. Remarkable how much they will
distort. Fun experience to do ONCE. Best of luck, Hank<br><br><p>-----------------------------------------</p>
From: "Harold Manifold"<br>
To: "<a>gradea1@charter.net</a>"<br>
Cc:<br>
Sent: Monday May 3 2021 8:44:09AM<br>
Subject: RE: [Healeys] Spokes and Truing Wheels<br><br><div>
<p class="MsoNormal">Hank,</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">Thanks for the reply. Did you find any secret
sequence for loosening and tightening the spokes. I have a dial
gauge and can find the high spots and low spots but I seem to be
able to just move them around.</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">I agree this will tedious no matter what.</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">Harold</p>
<p class="MsoNormal"> </p>
<div style="border:none;border-top:solid #e1e1e1 1pt;padding:3pt 0in 0in 0in;">
<p class="MsoNormal" style="border:none;padding:0in;"><b>From:</b>
<a>gradea1@charter.net</a><br><b>Sent:</b> Sunday, May 2, 2021 6:21 PM<br><b>To:</b> <a>Harold Manifold</a><br><b>Cc:</b> <a>healeys@autox.team.net</a><br><b>Subject:</b> RE: [Healeys] Spokes and Truing Wheels</p>
</div>
<p class="MsoNormal"> </p>
<p class="MsoNormal">Harold- I made up this table with an axle hub
mounted vertically and a fixed post each side using two coffee stir
sticks as markers or guides. After lacing the wheel,
rotate to first get rid of up/down wobble and then tighten to keep
wheel round-equally from each post. (photos)</p>
<div>
<p class="MsoNormal"> </p>
</div>
<div>
<p class="MsoNormal">You are correct the spokes and nibs are 10-32,
but the thread angle is Whitworth (55 degrees-I believe) Use a
British tap to clean up threads. Don't use SAE.</p>
</div>
<div>
<p class="MsoNormal"> </p>
</div>
<div>
<p class="MsoNormal" style="margin-bottom:12pt;">Its a tedious task
but I did all 5 wheels for my 100, and they run perfect. Check a
bicycle/motorcycle shop for procedure. Have fun, Hank</p>
<p>-----------------------------------------</p>
<p class="MsoNormal" style="margin-bottom:12pt;">From: "Harold
Manifold via Healeys"<br>
To: "<a>healeys@autox.team.net</a>"<br>
Cc:<br>
Sent: Sunday May 2 2021 4:35:21PM<br>
Subject: [Healeys] Spokes and Truing Wheels</p>
<div>
<p class="MsoNormal">Hello,</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">What is the thread size for the spokes and
nipples It looks like 10-32 but a threading die doesn’t seem to
fit. Also, does anyone have a good procedure for truing wheels? I
was told Out of Round first then Wobble. I did the Out of Round on
one wheel and could get to 0.050” but no better.</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">Harold</p>
</div>
</div>
<p class="MsoNormal"> </p>
<p class="MsoNormal"> </p>
</div>
</div>
</div>
</div>
</div>
_______________________________________________<br>
Support Team.Net <a href="http://www.team.net/donate.html"></a><a href="http://www.team.net/donate.html">http://www.team.net/donate.html</a><br>
Suggested annual donation $12.75<br><br>
Archive: <a href="http://www.team.net/pipermail/healeys"></a><a href="http://www.team.net/pipermail/healeys">http://www.team.net/pipermail/healeys</a> <a href="http://autox.team.net/archive"></a><a href="http://autox.team.net/archive">http://autox.team.net/archive</a><br><br><a>Healeys@autox.team.net</a><br><a href="http://autox.team.net/mailman/listinfo/healeys"></a><a href="http://autox.team.net/mailman/listinfo/healeys">http://autox.team.net/mailman/listinfo/healeys</a><br><br>
Unsubscribe/Manage: <a href="http://autox.team.net/mailman/options/healeys/springer.mike51@gmail.com"></a><a href="http://autox.team.net/mailman/options/healeys/springer.mike51@gmail.com">http://autox.team.net/mailman/options/healeys/springer.mike51@gmail.com</a><br><br></blockquote>
</div>
</springer.mike51@gmail.com></body></html>