<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=Windows-1252">
<meta content="text/html; charset=utf-8">
</head>
<body>
<div dir="auto">I have rebuilt and trued a number of wire wheels over the past thirty years, starting with replacing spokes on my Made in India Dunlop chrome 60 spoke set. </div>
<div dir="auto">I broke so many spokes on those wheels that I ended up purchasing spokes and nipples in bulk direct from Dayton.</div>
<div dir="auto">The information I was given by them was that truing wheels to plus or minus 0.030" was the best they could expect when building new wheels!</div>
<div dir="auto"><br>
</div>
<div dir="auto">Laurie Wilford </div>
<div dir="auto"><br>
</div>
<div id="composer_signature" dir="auto">
<div dir="auto" style="font-size:85%; color:#575757">Sent from my Galaxy</div>
</div>
<div dir="auto"><br>
</div>
<div><br>
</div>
<div><br>
</div>
<div>-------- Original message --------</div>
<div>From: Henry G Leach via Healeys <healeys@autox.team.net> </div>
<div>Date: 2021-05-03 1:40 p.m. (GMT-05:00) </div>
<div>To: 'Harold Manifold' <manifold@telus.net> </div>
<div>Cc: "'healeys@autox.team.net'" <healeys@autox.team.net> </div>
<div>Subject: Re: [Healeys] Spokes and Truing Wheels </div>
<div><br>
</div>
<div>Hi Harold- yes, I also used a dial gauge and that, unfortunately, is too fine an instrument for the crude wheels that we have. It will drive you crazy to try to "0" out the wheel. Looks like you got close and could not effect a change. Me too. That is
probably as good as it will get. I think the eye is a better judge of the "quality" of the wheel-if you see runout try to move it to be less. Of the five wheels I did I rated them as the best-worse and used #5 for the spare, putting the best on the fronts.
They are very close to "good" as round goes. A wonderful theory that in practical use has some forgiveness.
<div><br>
</div>
<div>You could send them assembled, off to Hendricks Wheel service and they may be able to do a tighter finish. Folks swear that their trued, shaved, rebuilt wheels from them are the cats meow.</div>
<div><br>
</div>
<div>A couple of things I did in assembly: I used anti seize compound on all the spoke threads-just enough to make so you could possibly undo them later. Then at the other end, I used marine sealant on the hub nubs to seal in grease and seal out water. May
work for awhile. I also ran a 2" duct tape seal over the nibs in the rim, in addition to the rubber rim seal (which does not cover them well.)</div>
<div><br>
</div>
<div>The only secret sequence I found was when you tightened one nib, you needed to go to the exact opposite nib to compensate for the "pull" on the shape of the wheel. Remarkable how much they will distort. Fun experience to do ONCE. Best of luck, Hank<br>
<br>
<div class="reply-new-signature"></div>
<p>-----------------------------------------</p>
From: "Harold Manifold" <br>
To: "gradea1@charter.net"<br>
Cc: <br>
Sent: Monday May 3 2021 8:44:09AM<br>
Subject: RE: [Healeys] Spokes and Truing Wheels<br>
<br>
<div class="WordSection1">
<p class="MsoNormal">Hank,</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">Thanks for the reply. Did you find any secret sequence for loosening and tightening the spokes. I have a dial gauge and can find the high spots and low spots but I seem to be able to just move them around.</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">I agree this will tedious no matter what.</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">Harold</p>
<p class="MsoNormal"> </p>
<div style="border:none; border-top:solid #E1E1E1 1pt; padding:3pt 0in 0in 0in">
<p class="MsoNormal" style="border:none; padding:0in"><b>From:</b> <a>gradea1@charter.net</a><br>
<b>Sent:</b> Sunday, May 2, 2021 6:21 PM<br>
<b>To:</b> <a>Harold Manifold</a><br>
<b>Cc:</b> <a>healeys@autox.team.net</a><br>
<b>Subject:</b> RE: [Healeys] Spokes and Truing Wheels</p>
</div>
<p class="MsoNormal"> </p>
<p class="MsoNormal">Harold- I made up this table with an axle hub mounted vertically and a fixed post each side using two coffee stir sticks as markers or guides. After lacing the wheel, rotate to first get rid of up/down wobble and then tighten to keep
wheel round-equally from each post. (photos)</p>
<div>
<p class="MsoNormal"> </p>
</div>
<div>
<p class="MsoNormal">You are correct the spokes and nibs are 10-32, but the thread angle is Whitworth (55 degrees-I believe) Use a British tap to clean up threads. Don't use SAE.</p>
</div>
<div>
<p class="MsoNormal"> </p>
</div>
<div>
<p class="MsoNormal" style="margin-bottom:12pt">Its a tedious task but I did all 5 wheels for my 100, and they run perfect. Check a bicycle/motorcycle shop for procedure. Have fun, Hank</p>
<p>-----------------------------------------</p>
<p class="MsoNormal" style="margin-bottom:12pt">From: "Harold Manifold via Healeys"<br>
To: "healeys@autox.team.net"<br>
Cc:<br>
Sent: Sunday May 2 2021 4:35:21PM<br>
Subject: [Healeys] Spokes and Truing Wheels</p>
<div>
<p class="MsoNormal">Hello,</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">What is the thread size for the spokes and nipples It looks like 10-32 but a threading die doesn’t seem to fit. Also, does anyone have a good procedure for truing wheels? I was told Out of Round first then Wobble. I did the Out of Round
on one wheel and could get to 0.050” but no better.</p>
<p class="MsoNormal"> </p>
<p class="MsoNormal">Harold</p>
</div>
</div>
<p class="MsoNormal"> </p>
<p class="MsoNormal"> </p>
</div>
</div>
</div>
</body>
</html>