<html>
<head>
<meta http-equiv="Content-Type" content="text/html;
charset=windows-1252">
</head>
<body>
(non) progress report:<br>
<br>
Thinking Bill probably had the explanation, I clamped off the RF
flex line--the wheel I'd replaced the cylinder on--per Michael's
suggestion and, Voila!, a nice hard pedal. Thinking also that I
hadn't expelled a bubble, like Bill also suggested, I increased the
pressure on my pressure bleeding rig and bled all wheels again.
Still, a nice hard pedal, so I fired up my BJ8 to get it out of the
garage so I could pressure wash the undercarriage of the BN2 and
take it (BJ8) for a warm-up spin. Halfway around the 'block,' about
5 miles from home it started running very rough so I pulled into a
covid-closed restaurant parking lot and popped the bonnet; coolant
all over the passenger side of the engine bay. It appears the gasket
under the brass shut-off valve for the heater hoses sprung a leak,
so a call to AAA was in order. After getting the BJ8 flat-bedded
home I washed the 100's underside, put on the new wheels and tires
and hop in ... brake pedal goes to the floor! Since I could get some
brakes if I pumped the pedal a couple times I took a chance on a
short, abridged spin around a smaller block--the new wheels and
tires ride fantastic, and no 'scuttle shake' detected--then parked
it.<br>
<br>
Thanks for all the suggestions, folks. I meant to try the
'hold-the-pedal-to-the-floor-with-a-board' technique, but by EOD I
was so beat I forgot. I've had trouble bleeding brakes on the BJ8,
but the BN2 has generally cooperated until now. Damned if I can
explain why I can get a good hard pedal, which proceeds to go soft
from just sitting. Good thing I love these cars.<br>
<br>
Bob<br>
<br>
<div class="moz-cite-prefix">On 4/23/2021 9:06 PM, WILLIAM B
LAWRENCE wrote:<br>
</div>
<blockquote type="cite"
cite="mid:CY4PR13MB1143F80229CE83A0FFAE8F85A5449@CY4PR13MB1143.namprd13.prod.outlook.com">
<meta http-equiv="Content-Type" content="text/html;
charset=windows-1252">
<style type="text/css" style="display:none;">P {margin-top:0;margin-bottom:0;}</style>
<div style="font-family: Calibri, Helvetica, sans-serif;
font-size: 12pt; color: rgb(0, 0, 0);">
The problem with the double leading edge brakes on the 100s and
100-6s is that the bleeder screw is at a low point in the system
so it takes a little extra effort expel any entrained air. You
probably got a pretty good slug when you changed the wheel
cylinder. Probably keep bleeding that wheel and use various
techniques until you find the one that actually moves the air
out of the bleeder.</div>
<div style="font-family: Calibri, Helvetica, sans-serif;
font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Helvetica, sans-serif;
font-size: 12pt; color: rgb(0, 0, 0);">
Bill Lawrence</div>
<div style="font-family: Calibri, Helvetica, sans-serif;
font-size: 12pt; color: rgb(0, 0, 0);">
BN1 #554</div>
<hr style="display:inline-block;width:98%" tabindex="-1">
<div id="divRplyFwdMsg" dir="ltr"><font style="font-size:11pt"
face="Calibri, sans-serif" color="#000000"><b>From:</b>
Healeys <a class="moz-txt-link-rfc2396E" href="mailto:healeys-bounces@autox.team.net"><healeys-bounces@autox.team.net></a> on behalf of
Bob Spidell via Healeys <a class="moz-txt-link-rfc2396E" href="mailto:healeys@autox.team.net"><healeys@autox.team.net></a><br>
<b>Sent:</b> Saturday, April 24, 2021 3:04 AM<br>
<b>To:</b> Healeys <a class="moz-txt-link-rfc2396E" href="mailto:healeys@autox.team.net"><healeys@autox.team.net></a><br>
<b>Subject:</b> [Healeys] BN2 Brake Problem</font>
<div> </div>
</div>
<div class="BodyFragment"><font size="2"><span
style="font-size:11pt;">
<div class="PlainText">Listers,<br>
<br>
I have a problem with my BN2's brakes that is driving
(heh) me up the <br>
wall. Here's what I've done:<br>
<br>
- new shoes and cylinders in both rear wheels<br>
- one new cylinder in one front wheel (there's a total of
4 in the 2 <br>
front wheels)<br>
- new master cylinder<br>
<br>
I hadn't touched the M/C, so after all the installs I just
pressure bled <br>
as I usually do (this has worked well on my BJ8 for
decades and a couple <br>
times for the BN2). At first, I got decent pedal then,
after a period of <br>
time I lost it; the pedal would go to the floor with only
slight <br>
pressure (probably from the return springs). Thinking it
could only be <br>
the M/C, I sprung for a new TRW brand M/C but after
installing it and <br>
bleeding I got the same results. I've put 2 full quarts of
Castrol's <br>
finest 'synthetic' DoT4 through the system and tried
vacuum bleeding and <br>
old-fashioned 'pump and hold' method; same result for all
methods. I'm <br>
not losing fluid as far as I can tell, and the pedal will
pump up a bit <br>
with a half-dozen or so strokes, but will go back to the
floor after <br>
some time.<br>
<br>
Any and all ideas and suggestions accepted and welcomed.<br>
<br>
TIA,<br>
Bob<br>
_______________________________________________<br>
</div>
</span></font></div>
</blockquote>
<br>
</body>
</html>