<div dir="ltr"><div class="gmail_default" style="font-family:comic sans ms,sans-serif;font-size:small"><span style="font-family:arial,sans-serif">Bob, I looked into installing "O" rings into an accumulator many years ago but couldn't figure out how to get around the problem presented by the fact that the accumulator relieves pressure by allowing the cast iron rings to pass over radial holes in the body.</span></div><div class="gmail_default" style="font-family:comic sans ms,sans-serif;font-size:small"><span style="font-family:arial,sans-serif">When I tried them the "O" rings were forced into those pressure relief holes and tiny pieces were sliced off at each hole location!!<br></span></div><div class="gmail_default" style="font-family:comic sans ms,sans-serif;font-size:small"><span style="font-family:arial,sans-serif">How do the accumulators with "O" rings address that issue?</span></div><div class="gmail_default" style="font-family:comic sans ms,sans-serif;font-size:small"><span style="font-family:arial,sans-serif"><br></span></div><div class="gmail_default" style="font-family:comic sans ms,sans-serif;font-size:small"><span style="font-family:arial,sans-serif">M</span><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, Mar 26, 2021 at 10:26 AM Bob Spidell <<a href="mailto:bspidell@comcast.net">bspidell@comcast.net</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
<div>
Maybe of interest to some: AFAIK, all O/D accumulators came with
metal rings, which likely cause or at least contribute to scoring.
One of the Brit suppliers--probably AHS but I'm not sure--has an
accumulator setup that uses an O-ring(s) instead of metal rings,
which should prevent scoring. I rebuilt my O/D a couple years back,
and if I'd known of the O-ring type I would have installed it.
Earlier O/Ds used metal rings in the actuator pistons, but later
ones had O-rings, and it's logical to conclude LdeN went to O-rings
there because of excessive scoring of the cases (or, possibly,
because they were cheaper).<br>
<br>
<div>On 3/26/2021 6:03 AM, Michael Salter
via Healeys wrote:<br>
</div>
<blockquote type="cite">
<div dir="auto">Time this question was put to bed.
<div dir="auto">1. The throttle switch is not supposed to
disengage the overdrive if the dash switch is in the
"OVERDRIVE" position. If it does the system is wired
incorrectly. (BN1s are a little different)</div>
<div dir="auto">2. Overdrives which slip out, slip, or won't
engage WHEN HOT but do work when cold are invariably suffering
from low oil pressure which is almost always caused by
accumulator issues. The "O" rings on the outside of the
accumulator sleeve can be a problem but in my experience
scoring of the accumulator bore and damage to the rings and
piston are a more common cause.</div>
<div dir="auto">3. Overdrives and gearboxes in Healeys are meant
to be lubricated with engine oil. Decades ago I wrote to
Laycock DeNormanville, back when letters went in envelopes
with stamps, and received a response from their engineering
department indicating clearly that the oil specified for their
products was specified by the gearbox manufacturer and
whatever they specified was acceptable for the overdrive.</div>
<div dir="auto">M</div>
</div>
<br>
<div class="gmail_quote">
<div dir="ltr" class="gmail_attr">On Fri., Mar. 26, 2021, 2:13
a.m. WILLIAM B LAWRENCE via Healeys, <<a href="mailto:healeys@autox.team.net" target="_blank">healeys@autox.team.net</a>>
wrote:<br>
</div>
<blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
<div>
<div>The symptoms I’ve seen and experienced are that the OD
will engage and function until the oil temp comes up and
the viscosity drops off and will then fail. I suppose it
depends on the degree of degradation of the o-rings.</div>
<hr style="display:inline-block;width:98%">
<div id="gmail-m_-7260173366705078485m_2913893478454826311divRplyFwdMsg" dir="ltr"><font style="font-size:11pt" face="Calibri, sans-serif" color="#000000"><b>From:</b> Healeys <<a href="mailto:healeys-bounces@autox.team.net" rel="noreferrer" target="_blank">healeys-bounces@autox.team.net</a>>
on behalf of Bob Spidell <<a href="mailto:bspidell@comcast.net" rel="noreferrer" target="_blank">bspidell@comcast.net</a>><br>
<b>Sent:</b> Thursday, March 25, 2021 11:14 PM<br>
<b>To:</b> <a href="mailto:healeys@autox.team.net" rel="noreferrer" target="_blank">healeys@autox.team.net</a> <<a href="mailto:healeys@autox.team.net" rel="noreferrer" target="_blank">healeys@autox.team.net</a>><br>
<b>Subject:</b> Re: [Healeys] overdrive problem</font>
<div> </div>
</div>
<div>Sure, but wouldn't faulty O-rings prevent the OD from
engaging in the first place? Just guessing, but wouldn't a
deficient pump cause same symptoms?<br>
<br>
<br>
<div>On 3/25/2021 4:07 PM, WILLIAM B LAWRENCE via Healeys
wrote:<br>
</div>
<blockquote type="cite">
<div>Sorry, but the Laycock deNormanville overdrive is
not supposed to kick down automatically. The most
common fault that causes the OD to drop out is faulty
o-rings on the accumulator sleeve. This won’t allow
the OD to build full operating pressure.</div>
<div><br>
</div>
<div>Bill Lawrence</div>
<div>BN1 #554</div>
<hr style="display:inline-block;width:98%">
<div id="gmail-m_-7260173366705078485m_2913893478454826311x_divRplyFwdMsg" dir="ltr"><font style="font-size:11pt" face="Calibri, sans-serif" color="#000000"><b>From:</b> Healeys
<a href="mailto:healeys-bounces@autox.team.net" rel="noreferrer" target="_blank"><healeys-bounces@autox.team.net></a>
on behalf of Kees Oudesluijs via Healeys
<a href="mailto:healeys@autox.team.net" rel="noreferrer" target="_blank"><healeys@autox.team.net></a><br>
<b>Sent:</b> Tuesday, March 23, 2021 7:37 AM<br>
<b>To:</b> <a href="mailto:healeys@autox.team.net" rel="noreferrer" target="_blank">
healeys@autox.team.net</a> <a href="mailto:healeys@autox.team.net" rel="noreferrer" target="_blank">
<healeys@autox.team.net></a><br>
<b>Subject:</b> Re: [Healeys] overdrive problem</font>
<div> </div>
</div>
<div><font size="2"><span style="font-size:11pt">
<div>That is the way it should be when
accelerating hard, Kick down!!<br>
<br>
Kees Oudesluijs<br>
<br>
<br>
Op 23-3-2021 om 01:06 schreef healeymanjim via
Healeys:<br>
> friends BT7 had o/d quit. solenoid was bad
so replaced it. now it will go into o/d but pop
out when accelerating. any<br>
> ideas what the cause is and the fix?<br>
</div>
</span></font></div>
</blockquote>
<br>
</div>
</div>
</blockquote>
</div>
</blockquote>
<br>
</div>
_______________________________________________<br>
Support Team.Net <a href="http://www.team.net/donate.html" rel="noreferrer" target="_blank">http://www.team.net/donate.html</a><br>
Suggested annual donation $12.75<br>
<br>
Archive: <a href="http://www.team.net/pipermail/healeys" rel="noreferrer" target="_blank">http://www.team.net/pipermail/healeys</a> <a href="http://autox.team.net/archive" rel="noreferrer" target="_blank">http://autox.team.net/archive</a><br>
<br>
<a href="mailto:Healeys@autox.team.net" target="_blank">Healeys@autox.team.net</a><br>
<a href="http://autox.team.net/mailman/listinfo/healeys" rel="noreferrer" target="_blank">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br>
Unsubscribe/Manage: <a href="http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com" rel="noreferrer" target="_blank">http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com</a><br>
<br>
</blockquote></div>