<div dir="auto">Thanks for all that Bob. <div dir="auto">One comment regarding increasing the cooling system pressure. </div><div dir="auto">I rebuild quite a few Healey water pumps and can say unequivocally that the seal type used in both the early and late style of 6 cylinder pump will not handle much more than 7 p.s.i. </div><div dir="auto">I would not recommend trying that approach. </div><div dir="auto"><br></div><div dir="auto">M</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat., Mar. 6, 2021, 4:58 p.m. , <<a href="mailto:rfbegani@gmail.com">rfbegani@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div lang="EN-US" link="blue" vlink="purple" style="word-wrap:break-word"><div class="m_-4589831803634194626WordSection1"><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">Bob & Mike:<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">You both may have seen my requests on overheating of my BJ8 and the response from the group.  As a result, I purchased an infrared thermometer to determine if my water gauge was giving accurate readings.  The thermometer gun told me that my water gauge was 30 degrees higher than the temperature of the sensor attached to the block.  At the same time, I noticed my gauge will show 120 degrees at rest instead of going down to 90 degrees which would indicate a 30-degree high reading.  In May when I leave for cool Michigan, I will send the gauge to Nisonger to be rebuilt.<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">I began to test the temperature of the water going through the cooling system at the inlet to and outlet from the block, inlet and outlet to the radiator and the upper and lower hoses while the engine is running at idle and at 2-3 Thousand rpm.  The chart I created to record these temperatures allowed me to produce observations or averages because the flow of the water is dependent upon the rpms of the engine.  The engine has overheated all of the 40 years I have owned it and has only 1000 miles on the new speedo since rebuilding to 20 over. <u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">At the radiator inlet 134 outlet 85 at high rpms with electric fan operating.<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">                        inlet 103 outlet 94 at idle rpms with electric fan operating. <u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">The above temperatures are recorded at the inlet and all along the hoses.<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">These temperatures indicate the pump is circulating water with sufficient gallons to cool the engine only when the engine is at high rpms.  At idle the pump does not circulate sufficient water to keep the engine cool.  This is especially true when you have been operating the engine at high speed and come down to 30 – 40 mph and stop and go traffic.  Maybe the real answer is to install an electric pump for constant cooling water?<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">In the past week, I have installed a large Dorman coolant recovery tank and a new 7 psi 1 inch radiator cap because I learned that our radiators have a long neck.  Both those changes have reduced my problem of very high overheating and resulting boiling over.  In addition, when my water gauge shows 212 degrees the water temperature is actually 30 degrees less or approximately 185 degrees.  Also, I am not boiling over and loosing coolant.  Nevertheless, the engine water temperature is still spiking to 210 plus degrees true when coming off highway speeds.  <u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">In my review of various sites, the radiator equipment suppliers and others are recommending increasing the pressure in the classic car systems to 15 psi plus, and coolant recovery tanks “if your coolant system, radiator, hoses etc. is new” and therefore can hold the pressure.  Unfortunately, I have not found any maker of a 1 inch depth x 2.33 inch diameter radiator cap except our 7 psi cap so I can try such a pressurized system.<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">Another suggestion on an older discussion at the British Car Forum indicated some of the Ontario car owners had switched to Evans Waterless Coolant rather than 50/50 coolant water mixture.<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">I still have no idea why a minority of our group has overheating problems.  More ideas?<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">Regards,<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif">Bob Begani 67 BJ8 <u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:14.0pt;font-family:"Arial",sans-serif"><u></u> <u></u></span></p><div style="border:none;border-top:solid #e1e1e1 1.0pt;padding:3.0pt 0in 0in 0in"><p class="MsoNormal"><b>From:</b> Healeys <<a href="mailto:healeys-bounces@autox.team.net" target="_blank" rel="noreferrer">healeys-bounces@autox.team.net</a>> <b>On Behalf Of </b>Michael Salter via Healeys<br><b>Sent:</b> Saturday, March 6, 2021 12:20 PM<br><b>To:</b> Bob Spidell <<a href="mailto:bspidell@comcast.net" target="_blank" rel="noreferrer">bspidell@comcast.net</a>><br><b>Cc:</b> <a href="mailto:healeys@autox.team.net" target="_blank" rel="noreferrer">healeys@autox.team.net</a><br><b>Subject:</b> Re: [Healeys] 100 water pumps<u></u><u></u></p></div><p class="MsoNormal"><u></u> <u></u></p><div><div><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Arial",sans-serif">Yes Bob, there is something wrong with our assumptions regarding the cooling system not being "large" enough. </span><span style="font-size:12.0pt"><u></u><u></u></span></p></div><div><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Arial",sans-serif">My wifes Maxima is around 300 HP and the radiator has less area than the 100. Certainly it has a couple of very effective electric fans but they really don't cut in very often unless you have the AC on.</span><span style="font-size:12.0pt"><u></u><u></u></span></p></div><div><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Arial",sans-serif">I'm suspicious of the rate of circulation but I've talked to Larry Varley about this subject and he indicated that increasing the size of the water pump annular orifice didn't make much difference when he tried it.</span><span style="font-size:12.0pt"><u></u><u></u></span></p></div><div><p class="MsoNormal"><span style="font-size:12.0pt"><u></u> <u></u></span></p></div><div><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Arial",sans-serif">M</span><span style="font-size:12.0pt;font-family:"Comic Sans MS""><u></u><u></u></span></p></div><div><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Comic Sans MS""><u></u> <u></u></span></p></div><div><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Comic Sans MS"">M<u></u><u></u></span></p></div></div><p class="MsoNormal"><u></u> <u></u></p><div><div><p class="MsoNormal">On Sat, Mar 6, 2021 at 11:42 AM Bob Spidell <<a href="mailto:bspidell@comcast.net" target="_blank" rel="noreferrer">bspidell@comcast.net</a>> wrote:<u></u><u></u></p></div><blockquote style="border:none;border-left:solid #cccccc 1.0pt;padding:0in 0in 0in 6.0pt;margin-left:4.8pt;margin-right:0in"><div><p class="MsoNormal" style="margin-right:0in;margin-bottom:12.0pt;margin-left:11.4pt">I sold my late father's 1955 Thunderbird to my BFF. These cars have a very similar problem to Healeys overheating, esp. at idle. When Ford stuffed the 292ci Y-Block into the T-Bird, they found the engine was (essentially) too short for the long-hooded car, so they 'engineered'--I use the term loosely--a cast iron spacer to move the fan closer to the radiator. The spacer had the added 'benefit' of severely limiting coolant flow through the pump and radiator; there are some aftermarket fixes and my friend, after doing the usual radiator re-core, better fan, etc. installed both a better pump (larger vanes) and a re-engineered spacer. Attached pic is not of the spacer he used--I can't find the link to it--but it shows the general idea (Ford basically put a 'dam' in the cooling system to block flow, and the improved spacers mostly remove it). It appears this approach has improved cooling, though the engine probably still gets warm if it has to sit too long at idle. Link is to one of the improved pumps:<br><br><a href="https://www.classictbird.com/Water-Pump-Modified-for-Higher-Output-1-Per-car/productinfo/8501HO/" target="_blank" rel="noreferrer">https://www.classictbird.com/Water-Pump-Modified-for-Higher-Output-1-Per-car/productinfo/8501HO/</a><br><br>Anyways, after doing all the usual stuff to increase cooling, esp. on my BJ8, I've wondered if a similar approach would work on Healeys. Their pumps have very small vanes, and the cavity in which the vanes operate seems pretty small for such a large lump of cast iron (I'm guessing an uprated radiator core won't help much if the coolant flow is still hampered; at least, that's what I've found). This is probably not an option as, of course, our engines don't have a similar spacer to be improved upon, and it would be a major task to increase both the cavity's size and the pump (but I can dream).<br><br>ps. The overheating issue with Healeys is usually attributed to too big of an engine in too small of an engine compartment, and too little airflow. But, the engine bay in an old T-Bird is huge by comparison--and the engine not terribly larger in displacement--and still suffers the same problem.<br><br>Bob <u></u><u></u></p></div><p class="MsoNormal" style="margin-bottom:12.0pt"><u></u> <u></u></p></blockquote></div></div></div></blockquote></div>