<div style="color:black;font: 10pt arial;">
<div>Hello Everybody!</div>

<div><br>
</div>

<div>Thought I would give a followup on this.  First thanks to those of you who replied.  I found the suggestions helpful.  I wound up making numerous attempts with many variations but none worked so well.  I will not go into those.  I finally did what I thought of early in the task but was trying to avoid removing bullets.  I understand there are other ways which have worked for several of you but here is what I did.  Maybe it will help someone in the future.</div>

<div><br>
</div>

<div>First, remove the shortest bullet using a solder gun to melt the solder.  (You might try to skip this step and see how it goes.)  Push a stiff elec wire (I used a 14 or 16 gauge) up the stator tube from the front.  You can go through the grill.  Once it is through remove the bullet from the longest wire in the har and solder the pull wire to the wire.  Feed/push/pull the har through the tube.  Once it is out pull the end through the grill, place a small board on the splash apron and resolder the two bullets.  Done!</div>

<div><br>
</div>

<div>Note:  If you changed the orientation of the stator tube you will need to reposition it with slot down so the teats in the traf assembly will slide into it.</div>
<br>
<br>

<div style="font-family:arial,helvetica;font-size:10pt;color:black">-----Original Message-----<br>
From: Keith Pennell via Healeys <healeys@autox.team.net><br>
To: healeys <healeys@autox.team.net><br>
Sent: Fri, Oct 4, 2019 6:28 pm<br>
Subject: [Healeys] Traffiator install woes<br>
<br>

<div id="yiv8338450310">

<div style="color:black;font:10pt arial;">

<div style="font-family:arial, helvetica;font-size:10pt;color:black;">

<div id="yiv8338450310">


<div style="color:black;font:10pt arial;">


<div>Well "assembly is the reverse of disassembly" right?  Managed to remove the wiring harness in the manner I have done times before.  That is, attaching a string to the har before pulling it up through the stator tube.  Problem is cannot get har back down through the tube.  After numerous attempts the string broke.  Does not help that the cloth insulation is deteriorated and missing on about the last foot of the har.</div>





<div><br>


</div>





<div>Any suggestions how to proceed</div>





<div>Keith</div>


</div>


</div>

</div>

</div>

</div>
_______________________________________________<br>
Support Team.Net <a href="http://www.team.net/donate.html" target="_blank" rel="noopener noreferrer">http://www.team.net/donate.html</a><br>
Suggested annual donation  $12.75<br>
<br>
Archive: <a href="http://www.team.net/pipermail/healeys" target="_blank" rel="noopener noreferrer">http://www.team.net/pipermail/healeys </a><a href="http://autox.team.net/archive" target="_blank" rel="noopener noreferrer">http://autox.team.net/archive</a><br>
<br>
<a href="mailto:Healeys@autox.team.net" rel="noopener noreferrer" ymailto="mailto:Healeys@autox.team.net">Healeys@autox.team.net</a><br>
<a href="http://autox.team.net/mailman/listinfo/healeys" target="_blank" rel="noopener noreferrer">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br>
Unsubscribe/Manage: <a href="http://autox.team.net/mailman/options/healeys/llennep@verizon.net" target="_blank" rel="noopener noreferrer">http://autox.team.net/mailman/options/healeys/llennep@verizon.net</a><br>
<br>
</div>
</div>