<div dir="ltr"><div><div><div><div><div><div><div>I have been on this list for quite a number of years and have learned uncountable and invaluable answers to problems I have had with my BJ7.  For the most part I remain quiet because of the vast knowledge, experience and quick responses of many of the individuals on this list.  I respect their knowledge and experience.  When I respond to others with my comments or solutions, it is usually off list but  I think I can offer some insight to the mounting of the overdrive unit.  Did I mention that this list is terrific!<br><br></div>Last year I had a problem with my overdrive not disengaging.  I thought about the problem and I removed the overdrive from the transmission, leaving the transmission attached to the engine.  It can't be done you say.  Oh but it can be.  I simply jacked the rear of the transmission up to the point that the overdrive could be pulled off.  I exchanged the overdrive unit for a rebuilt one and I was ready to replace the overdrive.  Now on to my solution.<br><br>Michael is quite right about the pump cam.  Looking at his pictures you can follow my solution.  I used mechanic's safety wire with a full loop thru the conveniently located hole in the pump base and wired the cam to the lowest position I could.  Note on the pump cam that there is a high point and a low point.  I placed the high point in the 12 o'clock position on the output shaft and therefore the low point was in the 6 o'clock position.  This placed the low point just above the pump roller offering the maximum clearance between the pump and the cam.<br><br></div>Here is the rest of my story.  There are two sets of internal clutch splines.  When looking at the two sets of splines, the upper spline rotates clockwise and should be positioned so that the groves line up (by eye or with a dummy shaft) with the ridges on the end of the output shaft.  At this point, don't worry about the lower set of splines.  On the bench, on the floor or in the car, slide the overdrive onto the output shaft.  You will have to rotate the overdrive back and forth a bit to get the first set of splines to slide onto the shaft. The overdrive should slide on to about 3/8" to 1/2" between the housings mating up.  Now that the overdrive is mounted to the first set of splines, leaving the overdrive on the transmission, use mechanics safety wire to wire the rear output flange, in about 3 places, to the overdrive unit.  Do this so tightly that the drive flange cannot move. I put a bolt in place on each side of the overdrive in the rear mounting (to the frame rails) holes.<br><br></div>Now, remove the overdrive unit and place it on the bench.  The drive flange cannot move and therefore the upper set of splines cannot move.  Look inside at the bottom set of splines.  They must be aligned with the upper splines.  Using a long screwdriver rotate the lower splines counterclockwise until they line up with the upper splines.  Now, slide the overdrive unit onto the output shaft and things should go together with no problem. Secure the overdrive to the transmission with the bolts, remove the safety wire from the pump and then remove the safety wire securing the drive flange.<br><br></div>This is what worked for me after many hours of trying to get the two sets of splines to line up.  Things went back together so easily that at first I didn't realize it was back together.  The really difficult part is getting the two sets of splines to align along with the fact that the lower splines rotate counterclockwise.<br><br></div>I hope this helps someone else.<br><br></div>Fred<br></div>63 BJ7<br></div><div class="gmail_extra"><br><div class="gmail_quote">On Sun, Jan 25, 2015 at 12:18 PM, John <span dir="ltr"><<a href="mailto:jmsdarch@sbcglobal.net" target="_blank">jmsdarch@sbcglobal.net</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div link="blue" vlink="purple" lang="EN-US"><div><p class="MsoNormal"><span style="font-size:11.0pt;font-family:"Calibri",sans-serif;color:#1f497d">Very elegant solution.<u></u><u></u></span></p></div></div><br>_______________________________________________<br>
Support Team.Net <a href="http://www.team.net/donate.html" target="_blank">http://www.team.net/donate.html</a><br>
Suggested annual donation  $12.75<br>
Archive: <a href="http://www.team.net/archive" target="_blank">http://www.team.net/archive</a><br>
Forums: <a href="http://www.team.net/forums" target="_blank">http://www.team.net/forums</a><br>
<br>
<a href="mailto:Healeys@autox.team.net">Healeys@autox.team.net</a><br>
<a href="http://autox.team.net/mailman/listinfo/healeys" target="_blank">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br>
Unsubscribe/Manage: <a href="http://autox.team.net/mailman/options/healeys/fredwescoe@gmail.com" target="_blank">http://autox.team.net/mailman/options/healeys/fredwescoe@gmail.com</a><br>
<br>
<br></blockquote></div><br></div>