[Healeys] speedometer Cable BJ8

warthodson at aol.com warthodson at aol.com
Mon Mar 4 15:32:29 MST 2019

Bob, 1. Have you installed the washer that goes between the angle drive & transmission? See parts book or Moss motors catalog.2. According British Car Specialists, if the square section of the inner cable is too long it will cause binding. Check their website for tech tips for the specific specifications.3. Have you tried connecting a drill to the cable while it is connected to the speedometer to verify that there is no binding in the cable/speedometer?
Gary Hodson
-----Original Message-----
From: Robert Begani <rfbegani at gmail.com>
To: healeys <healeys at autox.team.net>
Sent: Mon, Mar 4, 2019 3:35 pm
Subject: [Healeys] speedometer Cable BJ8

<!-- #yiv3751809253 _filtered #yiv3751809253 {font-family:"Cambria Math";panose-1:2 4 5 3 5 4 6 3 2 4;} _filtered #yiv3751809253 {font-family:Calibri;panose-1:2 15 5 2 2 2 4 3 2 4;} #yiv3751809253 #yiv3751809253 p.yiv3751809253MsoNormal, #yiv3751809253 li.yiv3751809253MsoNormal, #yiv3751809253 div.yiv3751809253MsoNormal {margin:0in;margin-bottom:.0001pt;font-size:11.0pt;font-family:"Calibri", sans-serif;} #yiv3751809253 a:link, #yiv3751809253 span.yiv3751809253MsoHyperlink {color:#0563C1;text-decoration:underline;} #yiv3751809253 a:visited, #yiv3751809253 span.yiv3751809253MsoHyperlinkFollowed {color:#954F72;text-decoration:underline;} #yiv3751809253 span.yiv3751809253EmailStyle17 {font-family:"Arial", sans-serif;color:windowtext;font-weight:normal;font-style:normal;text-decoration:none none;} #yiv3751809253 .yiv3751809253MsoChpDefault {font-family:"Calibri", sans-serif;} _filtered #yiv3751809253 {margin:1.0in 1.0in 1.0in 1.0in;} #yiv3751809253 div.yiv3751809253WordSection1 {} -->So as part of putting the tunnel and interior back together so I can go for a ride soon, I looked at the speedo angle gear.   On the old gear the short cable that fits into the trans had sheared off, so I installed a new angle gear.  Just to see if that was working I installed the short piece of cable, turned on the engine, engaged the gear and looked down and saw the piece of cable spinning.  Then I took out the piece of cable and attached the speedo cable to the dash.  It was not spinning.  Interesting.  So I removed the cable from the housing and fit it into the angle drive gear and no movement.  Thinking it might be a problem of load, reinstalled the short piece, it spins even when I apply hand pressure to the end.  Looking at the cable and the housing and the fitting of the cable up to the stop, etc. cannot figure why it does not spin.  Before I buy a new cable and housing do any of you have ideas?  Bob Begani_______________________________________________
Support Team.Net http://www.team.net/donate.html
Suggested annual donation  $12.75

Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive

Healeys at autox.team.net

Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/warthodson@aol.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/healeys/attachments/20190304/7a1ea0a4/attachment.html>

More information about the Healeys mailing list