[Healeys] Strange Timing Setting

[WILLIAM B LAWRENCE]

I don't remember if the mark on the damper is located on the center, fixed, portion or the outer. rubber suspended, portion. If the latter then maybe the damper has slipped out of register.


Bill Lawrence

BN1 #554

________________________________
From: Healeys <healeys-bounces at autox.team.net> on behalf of Patrick & Caroline Quinn <p_cquinn at tpg.com.au>
Sent: Saturday, February 10, 2018 10:42:59 PM
To: 'Per Schoerner'
Cc: healeys at autox.team.net
Subject: Re: [Healeys] Strange Timing Setting


Hello Per



I thought about that, but as No 1 is at top dead centre when the pointer is towards the notch in the harmonic balancer I can’t see how it can be.



Many thanks



Patrick Quinn



From: Per Schoerner [mailto:per at schoerner.se]
Sent: Sunday, 11 February 2018 6:18 AM
To: Patrick & Caroline Quinn
Cc: healeys at autox.team.net
Subject: Re: [Healeys] Strange Timing Setting



Patrick

You have installed the cam chain incorrectly. I assume you have the workshop manual. Look in section A.25 for the correct procedure.



Best, Per

Skickat från min iPad

10 feb. 2018 kl. 11:35 skrev Patrick & Caroline Quinn <p_cquinn at tpg.com.au<mailto:p_cquinn at tpg.com.au>>:

Greetings



Perhaps someone has come across this before.



About to start the engine in the BN3 after a complete rebuild. The engine is a very early C-series six-cylinder and the rebuild included new bearings throughout, pistons, sleeves, valves, vernier adjustable timing chain etc.



When setting the timing all the settings were done by the book. Tappets at 12 thou, the pointer on the timing chain cover is pointing to the notch in the harmonic balancer, the gear shaft drive from the oil pump/camshaft is at 20 to 2 and the offset distributor drive is correct. Number 1 piston is top dead centre and the rocker gear is rocking.



Imaging please looking down at the open distributor and it’s a clock face. According to the book, the rotor button arm should be at 2 o’clock or firing No 1 spark plug.



However the rotor button is a 10 o’clock.



So it’s not 180 degrees out, but 120 degrees.



Of course you could get around it by changing the spark plug leads, but the result looks untidy. An alternative is to rotate the geared shaft drive clockwise by 120 degrees.



Any suggestions?



Thanks



Patrick Quinn

Blue Mountains, Australia

_______________________________________________
Support Team.Net<https://nam01.safelinks.protection.outlook.com/?url=http%3A%2F%2FTeam.Net&data=02%7C01%7C%7C59d44727cacc4a88db0008d570e3993d%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636539045191578712&sdata=DxCfozhiP%2BKUY2rZXdZHFT%2FKpQbtx%2FK41xp7zQ2eNwg%3D&reserved=0> http://www.team.net/donate.html<https://nam01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.team.net%2Fdonate.html&data=02%7C01%7C%7C59d44727cacc4a88db0008d570e3993d%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636539045191578712&sdata=m8s9FzPyw16M3D%2F%2FX8pTTfloRbWmmm9i6oy%2F59Q92yU%3D&reserved=0>
Suggested annual donation  $12.75
Archive: http://www.team.net/archive<https://nam01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.team.net%2Farchive&data=02%7C01%7C%7C59d44727cacc4a88db0008d570e3993d%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636539045191578712&sdata=MGcW0f1BvrrzBs0BaTPhxwMPjl6K9uVLjhTzUA4WM4A%3D&reserved=0>
Forums: http://www.team.net/forums<https://nam01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.team.net%2Fforums&data=02%7C01%7C%7C59d44727cacc4a88db0008d570e3993d%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636539045191578712&sdata=FVEoCLPMuTC0Ic%2FTe8Cx2szUzGnjL4zZwS7uydYWRko%3D&reserved=0>

Healeys at autox.team.net<mailto:Healeys at autox.team.net>
http://autox.team.net/mailman/listinfo/healeys<https://nam01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fautox.team.net%2Fmailman%2Flistinfo%2Fhealeys&data=02%7C01%7C%7C59d44727cacc4a88db0008d570e3993d%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636539045191578712&sdata=IarnGRjFcTzhwvfWunXUtyRMhbtjjgvVYrPzxiF9wuQ%3D&reserved=0>

Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/per@schoerner.se<https://nam01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fautox.team.net%2Fmailman%2Foptions%2Fhealeys%2Fper%40schoerner.se&data=02%7C01%7C%7C59d44727cacc4a88db0008d570e3993d%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636539045191578712&sdata=VPUVTRFRXHkS%2BRw0GJ5w7CMNbqrZlzKmLa0mZb5ieBI%3D&reserved=0>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/healeys/attachments/20180211/06eecaf6/attachment.html>