[Healeys] Fwd: Re: BJ8 Windshield Replacement

[George Haywood]

Jim,     DON'T BUY THE CHEAPER GLASS!!!😤                                                                                                  
On Apr 9, 2017 11:05 AM, Jim Frakes <JimFrakes at frakes-eng.com> wrote:
>
> Thanks for info George. I was. contemplating the cheaper glass. 
> Jim 
>
> Sent from my iPhone 
>
> > On Apr 9, 2017, at 10:52 AM, George Haywood <ghaywood at ec.rr.com> wrote: 
> > 
> > ---------- Forwarded message ---------- 
> > From: George Haywood <ghaywood at ec.rr.com> 
> > Date: Apr 9, 2017 8:58 AM 
> > Subject: Re: [Healeys] BJ8 Windshield Replacement 
> > To: Bob Spidell <bspidell at comcast.net> 
> > Cc: 
> > 
> >> Hi Bob,  You don't have to remove anything but the inner frame to replace just the glass.  Only take off the whole frame if you need to replace the frame to shroud seal(THAT'S ANOTHER ONE OF THOSE CASE OF BEER JOBS).  I think you have to remove the top outer frame and the screws on the side pillars in the door openings on each side.  I think then the inner frame will slide out.  I'm glad you got the Pilkington glass.  I got one of the less expensive screens and it was not wide enough to seal from side to side. After spending the extra $300 or so for the Pilkington the seals went on better.  Take care,  George Haywood, '65 bj8 
> >> 
> >>> On Apr 8, 2017 6:29 PM, Bob Spidell <bspidell at comcast.net> wrote: 
> >>> 
> >>> Now I'm confused ... it looks like the glass should just slide out of 
> >>> the inner frame; you're saying I have to remove the whole 
> >>> kit-and-kaboodle, including the outer frame and frame-to-shroud seal? 
> >>> 
> >>> Bob 
> >>> 
> >>> 
> >>>> On 4/8/2017 3:18 PM, Charlie Schott wrote: 
> >>>> I've done it on a BJ8 and a BT7 windshield and it's not hard to do. 
> >>>> Make sure that you have good corner brackets and the right length 
> >>>> screws. The hardest part is pulling the lower seal thru the T slot. 
> >>>> Use plenty of liquid dishwater soap and grab the end with vice grips 
> >>>> to pull it. 
> >>>> 
> >>>> Regards, 
> >>>> 
> >>>> Charlie Schott 
> >>>> 
> >>>> -----Original Message----- From: Bob Spidell 
> >>>> Sent: Saturday, April 08, 2017 1:51 PM 
> >>>> To: Healeys 
> >>>> Subject: [Healeys] BJ8 Windshield Replacement 
> >>>> 
> >>>> Listers, 
> >>>> 
> >>>> Anyone replaced the windshield--just the glass and enclosing seal--on a 
> >>>> BJ8?  I have new glass, would order the seal kit from Moss (part# 
> >>>> 682-028), and have a 'pro' do the installation (unless this is easy 
> >>>> enough for a ham-fisted DIYer).  I don't want to pull the whole 
> >>>> thing--wind wings and all--just the 'main' glass. Anybody done this, or 
> >>>> is it best to let the pro do it? 
> >>>> 
> >>>> TIA, 
> >>>> Bob 
> >>>> 
> >>>> _______________________________________________ 
> >>>> Support Team.Net http://www.team.net/donate.html 
> >>>> Suggested annual donation  $12.75 
> >>>> Archive: http://www.team.net/archive 
> >>>> Forums: http://www.team.net/forums 
> >>>> 
> >>>> Healeys at autox.team.net 
> >>>> http://autox.team.net/mailman/listinfo/healeys 
> >>>> 
> >>>> Unsubscribe/Manage: 
> >>>> http://autox.team.net/mailman/options/healeys/schottc@knology.net 
> >>>> 
> >>> 
> >>> _______________________________________________ 
> >>> Support Team.Net http://www.team.net/donate.html 
> >>> Suggested annual donation  $12.75 
> >>> Archive: http://www.team.net/archive 
> >>> Forums: http://www.team.net/forums 
> >>> 
> >>> Healeys at autox.team.net 
> >>> http://autox.team.net/mailman/listinfo/healeys 
> >>> 
> >>> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/ghaywood@ec.rr.com 
> >>> 
> > _______________________________________________ 
> > Support Team.Net http://www.team.net/donate.html 
> > Suggested annual donation  $12.75 
> > Archive: http://www.team.net/archive 
> > Forums: http://www.team.net/forums 
> > 
> > Healeys at autox.team.net 
> > http://autox.team.net/mailman/listinfo/healeys 
> > 
> > Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/jimf@frakes-eng.com 
> > 
>
>
> CONFIDENTIALITY NOTICE
> The information contained in this e-mail is intended only for the use of the individual or entity to which it is addressed and it may contain information that is privileged or confidential.  If the reader of this message is not the intended recipient (or the employee or agent responsible to deliver it to the intended recipient), you are hereby notified that any dissemination, distribution, or copying of this communication is prohibited.  If you have received this e-mail in error, please notify us by telephone at the number listed above or by return e-mail. 
>