[Healeys] BN7 Top Frame
David Nock British Car Specialists
healeydoc at sbcglobal.net
Sat Dec 5 20:11:29 MST 2015
The wood bow that Moss sells is wrong. They sell the same bow for the 2 and 4 seater cars. They are not the same. We have two different header bows for the roadsters.
British Car Specialists
Stockton Ca 95205
Please feel free to view an interview with the Nock's in 2009
Sent from my iPad
> On Dec 5, 2015, at 6:13 PM, Richard Collins <gonnagitcha90 at hotmail.com> wrote:
> I have a suspicion that may be my problem but...
> My frame and windshield fit fine
> Richard C
> On Dec 5, 2015, at 20:09, Jim Wojcik <jvwojcik at comcast.net> wrote:
>> Hello, folks. I am not sure about the frame but I can tell you that at one point in my own restoration I bought a windshield glass from a friend with an BN6 and the shape was not the same, did not fit my frame, and I had to buy a specific curve for my 60 BN7. Jim Wojcik.
>> From: Healeys [mailto:healeys-bounces at autox.team.net] On Behalf Of Richard Collins
>> Sent: Saturday, December 5, 2015 4:31 PM
>> To: Peter Svilans <peter.svilans at rogers.com>
>> Cc: healeys at autox.team.net
>> Subject: Re: [Healeys] BN7 Top Frame
>> Thanks for this.
>> I tried it to fit on another BN7 and while it was closer to a fit on the too of the windshield frame than on mine, it still was off. That frame had a center toggle lock on it which held the frame in the center.
>> It could be the wood piece so I will take another look at it. I haven't played with it lately so with winter almost here I thought I would give it a shot again.
>> Thanks again !
>> Richard C
>> On Dec 5, 2015, at 15:55, Peter Svilans <peter.svilans at rogers.com> wrote:
>> Only one 2-seater top frame for BN6 and BN7, sorry.
>> One would have to see your installation, to see what the issue is.
>> The bows have an adjustment, two long screws in the feet of the main bow, but that would likely not affect your problem. Nor would the separate thin wedge piece under the clamp
>> The aluminum trim and rubber seal together should have enough thickness to get a nice over-center action from the clamps.
>> The wood bows from Moss have sometimes not had the correct curve to fit the windshield top exactly, in my experience. If the bow is not curved enough at the outer ends, then the clamps are too close to the pegs. Look very carefully at what is going on, and see what would be necessary to make the wood header bow provide enough height from the windshield to raise the steel top frame, and make the clamp just barely reach the peg at full extension. Maybe add a strip of 1/8 plywood between wood bow and aluminum ?
>> Attached pic shows "J" hook fully wound in, so rubber seal is removed for replacement with new. The lovely sharp-pointed "S" clamp is the correct original BN6-7 type, but the blunt BJ8 "safety" clamps sold now do the same job.
>> Best I can do without seeing yours.
>> <DSC00124 (Medium).JPG>
>> Support Team.Net http://www.team.net/donate.html
>> Suggested annual donation $12.75
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Healeys at autox.team.net
>> Unsubscribe/Manage: http://firstname.lastname@example.org
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Healeys at autox.team.net
> Unsubscribe/Manage: http://email@example.com
-------------- next part --------------
An HTML attachment was scrubbed...
More information about the Healeys