<div dir="ltr">This is correct. The thickness of the clamping surfaces must be the same. It also helps to tighten the<div>bottom clamp between the manifolds first. The intake will hang up on the pin between the intake ports</div><div> and not let the bottom of the intake seat all the way. Sometimes the hole for the pin is too tight.</div><div><br></div><div>Dean</div><div><br></div></div><br><div class="gmail_quote gmail_quote_container"><div dir="ltr" class="gmail_attr">On Wed, Apr 9, 2025 at 8:41 AM yellow04 via Fot <<a href="mailto:fot@autox.team.net">fot@autox.team.net</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div style="font-size:10pt;font-family:Verdana,Geneva,sans-serif">
<p>My money is on this one... Blowing out the bottom of the intake gaskets means you didn't get nearly enough pressure (if any) from that pesky lower mounting stud and clamp. I have found if you use anything other than a stock intake manifold and stock exhaust manifold, you must scrutinize the area where the clamps will sit to ensure the height is very similar. Or, modify the clamps by welding on something to make sure when the clamp rests on the appropriate bits of the intake and exhaust manifold, when the nut is tightened it puts equal pressure on both manifolds. Obviously, the mounting face on each manifold needs to be flat. Assuming you have everything in order, there is no reason a stock manifold gasket will not work, I have run them when I could not get my hands on the HD gaskets and they worked fine for me. </p>
<p>Last thought, the nuts that hold the manifolds on are notorious for loosening up in time, and especially after the first few heat cycles. And with everything installed, getting to the two bottom nuts can be a pain. But, failure to keep them properly torqued leads to blown out gaskets.</p>
<div id="m_5734550077102634702signature"> </div>
<p><br></p>
<p id="m_5734550077102634702reply-intro">On 2025-04-09 06:55, vfracing--- via Fot wrote:</p>
<blockquote type="cite" style="padding:0px 0.4em;border-left:2px solid rgb(16,16,255);margin:0px">
<div id="m_5734550077102634702replybody1">
<div>
<div style="font-family:arial;font-size:16px">
<div> </div>
<div dir="ltr">Lyman;</div>
<div dir="ltr"> </div>
<div dir="ltr"> another possible cause is a mis match in the thicknesses of the intake and exhaust manifold flanges.</div>
</div>
</div>
</div>
</blockquote>
</div>
_______________________________________________<br>
<a href="mailto:fot@autox.team.net" target="_blank">fot@autox.team.net</a><br>
<br>
<a href="http://www.fot-racing.com" rel="noreferrer" target="_blank">http://www.fot-racing.com</a><br>
<br>
Donate: <a href="http://www.team.net/donate.html" rel="noreferrer" target="_blank">http://www.team.net/donate.html</a><br>
Archive: <a href="http://autox.team.net/archive" rel="noreferrer" target="_blank">http://autox.team.net/archive</a> <a href="http://www.team.net/pipermail/fotUnsubscribe/Manage" rel="noreferrer" target="_blank">http://www.team.net/pipermail/fot<br>
Unsubscribe/Manage</a>: <a href="http://autox.team.net/mailman/options/fot/tr3a58dean@gmail.com" rel="noreferrer" target="_blank">http://autox.team.net/mailman/options/fot/tr3a58dean@gmail.com</a><br>
<br>
<br>
</blockquote></div>