<html><head><meta http-equiv="content-type" content="text/html; charset=utf-8"></head><body dir="auto">Joe:<div>We fill the gap completely with the anaerobic sealant. After cleaning all surfaces well I use the tapered nozzle they supply, cut it to fit into the trapezoid and then put a washer over the end to seal it up. Then I use one of those toothpaste tube keys to squeeze the tube, forcing the sealant gel into the trapezoid. Keep squeezing until I see the gel come out of the chamfered area at the base of the rear main cap. That way I know the trapezoidal volume is full.</div><div><br></div><div>It would probably be easier to buy a cartridge and put it in with a caulking gun, but that’s kinda pricey (~$50).</div><div><br></div><div>One regular size tube will do two engines. They get very hard to squeeze, even with the key, when they get near the end.</div><div><br></div><div>Because it is anaerobic, the gel won’t set up near the oil pan surface if you leave it exposed to air. Covering it with a piece of tape works well. You can then peel the tape off when you put the oil pan on. Or install the pan immediately. I have laid some “Ultra” black rtv right on top of the uncured aerobic gel, then put on the oil pan (with or without gasket as you prefer) and had it all set up just fine.</div><div><br></div><div>Hope this helps.</div><div><br></div><div>Regards,</div><div>Phil</div><div><br></div><div><br><div dir="ltr">Sent from my iPhone</div><div dir="ltr"><br><blockquote type="cite">On Feb 8, 2021, at 5:05 PM, Joe Boruch <jaboruch@yahoo.com> wrote:<br><br></blockquote></div><blockquote type="cite"><div dir="ltr"><div class="ydp957333a7yahoo-style-wrap" style="font-family: Helvetica Neue, Helvetica, Arial, sans-serif; font-size: 13px;"><div></div>
<div dir="ltr" data-setdir="false">Phil, how are you using the Anearobic sealant? Are you still using felt, or are you filling the gap where the felt would be with the Anearobic sealant? JoeB.</div><div><br></div>
</div><div id="ydp6edb2764yahoo_quoted_3109615661" class="ydp6edb2764yahoo_quoted">
<div style="font-family:'Helvetica Neue', Helvetica, Arial, sans-serif;font-size:13px;color:#26282a;">
<div>
On Monday, February 8, 2021, 04:28:25 PM EST, Phil Gott via Fot <fot@autox.team.net> wrote:
</div>
<div><br></div>
<div><br></div>
<div><div id="ydp6edb2764yiv6266475226"><div>Joe;<div>We’ve used the two of them together in two different engines. The Permatex was washed away from the rear main seal cap sides in both cases.<div>In fairness, in that application it takes a very long time to dry, and so it may have not set completely before we ran the engine. But we never had that issue until using the Driven synthetic oil. Which, BTW, seems to be really good stuff! Thanks to Ken Knight for the recommendation.</div><div>We’ve switched to Permatex Anaerobic sealant and it works very well. Much easier than soaked felt....</div><div>Phil Gott<br clear="none"><br clear="none"><div dir="ltr">Sent from my iPhone</div><div dir="ltr"><div class="ydp6edb2764yiv6266475226yqt4161954403" id="ydp6edb2764yiv6266475226yqtfd09427"><br clear="none"><blockquote type="cite">On Feb 8, 2021, at 4:20 PM, Joe Boruch <jaboruch@yahoo.com> wrote:<br clear="none"><br clear="none"></blockquote></div></div><div class="ydp6edb2764yiv6266475226yqt4161954403" id="ydp6edb2764yiv6266475226yqtfd79268"><blockquote type="cite"><div dir="ltr"><div class="ydp6edb2764yiv6266475226ydp8ac71bcbyahoo-style-wrap" style="font-family:Helvetica Neue, Helvetica, Arial, sans-serif;font-size:13px;"><div></div>
<div dir="ltr">Thanks David. Driven says that their oils should not cause your issue, but they think you may have an issue with fuel dilution. They did suggest not to use the Aviation Permatex, since it can be affected by <span><span style="color:rgb(38, 40, 42);font-family:Helvetica Neue, Helvetica, Arial, sans-serif;">aromatic solvents (which is what gasoline is)</span></span>. I looked at the instructions for Permatex Indian Head gasket shellac and it does not say that it is affected by aromatic solvents. The instructions for Aviation Permatex say that is affected by aromatic solvents. Looks like for my next build that I will go back to using Indian Head (if it has not been deemed to be un PC by then). </div><div dir="ltr"><br clear="none"></div><div dir="ltr">Thanks for bringing this issue to light. Joe B.</div><div dir="ltr"><br clear="none"></div><div dir="ltr"><br clear="none"></div><div dir="ltr"><br clear="none"></div>
</div><div class="ydp6edb2764yiv6266475226ydp1c628845yahoo_quoted" id="ydp6edb2764yiv6266475226ydp1c628845yahoo_quoted_3524273408">
<div style="font-family:'Helvetica Neue', Helvetica, Arial, sans-serif;font-size:13px;color:#26282a;">
<div>
On Monday, February 8, 2021, 02:57:29 PM EST, David Gott <triumphsix@yahoo.com> wrote:
</div>
<div><br clear="none"></div>
<div><br clear="none"></div>
<div><div id="ydp6edb2764yiv6266475226ydp1c628845yiv9309541554"><div>
Hi Joe,<div><br clear="none"></div><div>Here’s some pictures of the felts in my engine after being washed clean by Driven XP3. You can see the cement is washed out of the felts upon removal, and also the permatex parted along the seam of the block/cap. Never happened before running the oil. Hondabond held up just fine afterwards.</div><div><br clear="none"></div><div><div class="ydp6edb2764yiv6266475226ydp1c628845yiv9309541554yqt3639321438" id="ydp6edb2764yiv6266475226ydp1c628845yiv9309541554yqt29763"><blockquote class="ydp6edb2764yiv6266475226ydp1c628845yiv9309541554iosymail"><div class="ydp6edb2764yiv6266475226ydp1c628845yiv9309541554yqt8099896322" id="ydp6edb2764yiv6266475226ydp1c628845yiv9309541554yqtfd01941"><br clear="none"></div><blockquote></blockquote></blockquote></div></div>
</div></div></div>
</div>
</div></div></blockquote></div></div></div></div></div><div class="ydp6edb2764yqt4161954403" id="ydp6edb2764yqtfd05977">_______________________________________________<br clear="none"><a shape="rect" href="mailto:fot@autox.team.net" rel="nofollow" target="_blank">fot@autox.team.net</a><br clear="none"><br clear="none"><a shape="rect" href="http://www.fot-racing.com" rel="nofollow" target="_blank">http://www.fot-racing.com</a><br clear="none"><br clear="none">Donate: <a shape="rect" href="http://www.team.net/donate.html" rel="nofollow" target="_blank">http://www.team.net/donate.html</a><br clear="none">Archive: <a shape="rect" href="http://autox.team.net/archive " rel="nofollow" target="_blank">http://autox.team.net/archive </a><a shape="rect" href="http://www.team.net/pipermail/fot" rel="nofollow" target="_blank">http://www.team.net/pipermail/fot</a><br clear="none">Unsubscribe/Manage: <a shape="rect" href="http://autox.team.net/mailman/options/fot/jaboruch@yahoo.com" rel="nofollow" target="_blank">http://autox.team.net/mailman/options/fot/jaboruch@yahoo.com</a><br clear="none"><br clear="none"><br clear="none"></div></div>
</div>
</div></div></blockquote></div></body></html>