<div style="color:black;font: 10pt arial;">Good point, Chris;
<div><br>
</div>
<div>On the 721, there are 3 o-rings. Two seal the hydraulic fluid and, as you point out, are in contact with that on one side and whatever is in the bell housing on the other side. The third is between the transmission snout and the concentric slave body. It sees only what is in the bell housing. The two that were in contact with hydraulic fluid were swollen and rubbery, whereas the third was not, suggesting that the brake fluid is at fault. On the other hand, I have no idea if the o-rings are all the same type of rubber or not.</div>
<div><br>
</div>
<div>Pending clarification from Irv, I am going with the Quartermaster fluid, the 721 slave, and the Girling (now TRW) master cylinder.</div>
<div><br>
</div>
<div>Phil<br>
<br>
<br>
<div style="font-family:helvetica,arial;font-size:10pt;color:black">-----Original Message-----<br>
From: tr4racing <tr4racing@googlemail.com><br>
To: 'Phil Gott' <vfracing@aol.com>; 'Scott Janzen' <sjanzen@me.com>; fot@autox. team. net <fot@autox.team.net><br>
Sent: Thu, Apr 2, 2020 8:30 am<br>
Subject: AW: [Fot] Main Cap Fasteners and Clutches - 1300<br>
<br>
<div id="yiv3107912497"><style>#yiv3107912497 #yiv3107912497 -- _filtered {} _filtered {} #yiv3107912497 #yiv3107912497 p.yiv3107912497MsoNormal, #yiv3107912497 li.yiv3107912497MsoNormal, #yiv3107912497 div.yiv3107912497MsoNormal {margin:0cm;margin-bottom:.0001pt;font-size:11.0pt;font-family:sans-serif;} #yiv3107912497 a:link, #yiv3107912497 span.yiv3107912497MsoHyperlink {color:blue;text-decoration:underline;} #yiv3107912497 span.yiv3107912497E-MailFormatvorlage18 {font-family:sans-serif;color:windowtext;} #yiv3107912497 .yiv3107912497MsoChpDefault {font-size:10.0pt;} _filtered {} #yiv3107912497 div.yiv3107912497WordSection1 {} #yiv3107912497 </style>
<div>
<div class="yiv3107912497WordSection1">
<div class="yiv3107912497MsoNormal">The thing with concentric slaves sitting in the bell housing is often, that they get also oil from leaking engines or leaking gearboxes.</div>
<div class="yiv3107912497MsoNormal">Most slaves die from getting in contact with oil, rarely than with brake fluid.</div>
<div class="yiv3107912497MsoNormal"> </div>
<div class="yiv3107912497MsoNormal">Cheers</div>
<div class="yiv3107912497MsoNormal">Chris</div>
<div class="yiv3107912497MsoNormal"> </div>
<div class="yiv3107912497MsoNormal"> </div>
<div>
<div style="border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0cm 0cm 0cm;">
<div class="yiv3107912497yqt0847642290" id="yiv3107912497yqtfd89905">
<div class="yiv3107912497MsoNormal"><b><span lang="DE">Von:</span></b><span lang="DE"> Fot <fot-bounces@autox.team.net> <b>Im Auftrag von </b>Phil Gott via Fot<br clear="none"><b>Gesendet:</b> Donnerstag, 2. April 2020 13:44<br clear="none"><b>An:</b> Scott Janzen <sjanzen@me.com><br clear="none"><b>Cc:</b> 'Friends of Triumph' Triumph <fot@autox.team.net><br clear="none"><b>Betreff:</b> Re: [Fot] Main Cap Fasteners and Clutches - 1300</span></div>
</div>
</div>
</div>
<div class="yiv3107912497yqt0847642290" id="yiv3107912497yqtfd07932">
<div class="yiv3107912497MsoNormal"> </div>
<div class="yiv3107912497MsoNormal">To add to what Jim said: if you go the Quartermaster route, use the Quartermaster hydraulic fluid. They say any DOT 3 or 4 fluid will work, but it ain’t so. Some brake fluids will attack the rubber in the Quartermaster slave cylinder (see photo). I have compared the Quartermaster fluid with regular DOT 3 and 4 fluid and can tell you it is a BUNCH slipperier. The slave works much more smoothly.</div>
<div>
<div class="yiv3107912497MsoNormal"><img id="yiv3107912497_x0000_i1025" width="2016" height="1512" style="width:21.0in;min-height:15.75in;" yahoo_partid="2" src="cid:AOLP.70dee7c4-87f6-423d-850a-fc5a7576cdea"><br clear="none">BTW this is a Quartermaster 721 series concentric slave and throwout bearing.</div>
</div>
<div>
<div class="yiv3107912497MsoNormal">Phil Gott</div>
</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
<div>
<div class="yiv3107912497MsoNormal">Sent from my iPhone</div>
</div>
<div>
<div class="yiv3107912497MsoNormal"><br clear="none"><br clear="none"></div>
<blockquote style="margin-top:5.0pt;margin-bottom:5.0pt;">
<div class="yiv3107912497MsoNormal" style="margin-bottom:12.0pt;">On Apr 1, 2020, at 9:42 PM, Scott Janzen via Fot <fot@autox.team.net> wrote:</div>
</blockquote></div>
<blockquote style="margin-top:5.0pt;margin-bottom:5.0pt;">
<div>
<div class="yiv3107912497MsoNormal">I can tell you the size for the GT6 bits, if they are the same. </div>
<div>
<div class="yiv3107912497MsoNormal">Studs are 7/16” x3-1/2” overall length, 20TPI. </div>
</div>
<div>
<div class="yiv3107912497MsoNormal">My ARP box is marked 206-5404 Triumph TR7 main stud kit.</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
<div>
<div class="yiv3107912497MsoNormal">On Apr 1, 2020, at 7:58 PM, Brad Eells via Fot <<a rel="noopener noreferrer" shape="rect" ymailto="mailto:fot@autox.team.net" target="_blank" href="mailto:fot@autox.team.net">fot@autox.team.net</a>> wrote:</div>
</div>
<div class="yiv3107912497MsoNormal"> </div>
<div>
<div>
<div class="yiv3107912497MsoNormal">Hello Amici,</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
<div>
<div class="yiv3107912497MsoNormal">Thinking aloud here as I have time on my hands. A couple of questions:</div>
</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
<div>
<div class="yiv3107912497MsoNormal">1. Main cap fasteners - ARP does not make a main stud kit for the Spifire 1300 and does not list their studs by size either. If you have an ARP stud and nut set up, how did you order it? They have readily available a 7/16"x3" bolt for direct replacement of the OEM bolt.</div>
</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
<div>
<div class="yiv3107912497MsoNormal">2. Clutches - the vintage set up in my engines are a lightened factory flywheel, coming up just under 13 lbs with ring gear and a Borg & Beck clutch disc and plate. I've run 3 race weekends with the clutch that has been in the car for 43 years, so far without issue. I'm thinking I would like to stick with the flywheel I have with a good clutch solution. </div>
</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
<div>
<div class="yiv3107912497MsoNormal">I know this one is a bit of a can of worms but have at it with your valued thoughts. I'm looking for simple and reliable. I am not nearly as smart as the aeronautical engineer that built the car.</div>
</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
<div>
<div class="yiv3107912497MsoNormal">I hope you are all safe and well...</div>
</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
<div>
<div class="yiv3107912497MsoNormal">Cheers,</div>
</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
<div>
<div class="yiv3107912497MsoNormal">Brad</div>
</div>
<div>
<div class="yiv3107912497MsoNormal"><br clear="all"></div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div class="yiv3107912497MsoNormal"><b><span style="font-size:9.5pt;">Brad Eells</span></b><span style="font-size:9.5pt;"></span></div>
</div>
<div>
<div class="yiv3107912497MsoNormal"><b><span style="font-size:9.5pt;">Chino CA</span></b><span style="font-size:9.5pt;"></span></div>
</div>
<div>
<div class="yiv3107912497MsoNormal"><b><span style="font-size:9.5pt;">#72 FP 1969 Triumph Spitfire Mk3</span></b><span style="font-size:9.5pt;"></span></div>
</div>
<div>
<div class="yiv3107912497MsoNormal"><b><span style="font-size:9.5pt;">#35 DP 1962 Triumph TR4</span></b><span style="font-size:9.5pt;"></span></div>
</div>
<div>
<div class="yiv3107912497MsoNormal"><b><span style="font-size:9.5pt;">1965 Triumph TR4A IRS...for the road!</span></b><span style="font-size:9.5pt;"></span></div>
</div>
</div>
<div>
<div class="yiv3107912497MsoNormal"><b><span style="font-size:9.5pt;border:solid windowtext 1.0pt;padding:0cm;"><img id="yiv3107912497_x0000_i1026" border="0" width="96" height="94" style="width:1.0in;min-height:.9791in;" alt="Das Bild wurde vom Absender entfernt." src="cid:ymo6AEAszzQjRWSP3tKS"></span></b><span style="font-size:9.5pt;"></span></div>
</div>
<div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
<div class="yiv3107912497MsoNormal" style="margin-bottom:12.0pt;">_______________________________________________<br clear="none"><a rel="noopener noreferrer" shape="rect" ymailto="mailto:fot@autox.team.net" target="_blank" href="mailto:fot@autox.team.net">fot@autox.team.net</a><br clear="none"><br clear="none">http://www.fot-racing.com<br clear="none"><br clear="none">Donate: http://www.team.net/donate.html<br clear="none">Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot<br clear="none">Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/sjanzen@me.com<br clear="none"><br clear="none"></div>
</div>
</div>
<div class="yiv3107912497MsoNormal"> </div>
</div>
<div class="yiv3107912497MsoNormal" style="margin-bottom:12.0pt;">_______________________________________________<br clear="none">fot@autox.team.net<br clear="none"><br clear="none">http://www.fot-racing.com<br clear="none"><br clear="none">Donate: http://www.team.net/donate.html<br clear="none">Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot<br clear="none">Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/vfracing@aol.com<br clear="none"><br clear="none"></div>
</div>
</blockquote></div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>