[Fot] TR4 High speed driveline vibration

[Bill Tobin]

Clear as mud. That's basically what I did on my car when I put the Celica trans in.
Works fine.
Someone mentioned the exhaust system interference. Last year I did some work on the car and when I put the exhaust pipes back on, one was very close to the rear trans mount and gave a hellish hi-freq vibration. Ten minute fix and an oops!
Bill
  ----- Original Message ----- 
  From: malaboge at aol.com 
  To: toodamnfunky at comcast.net 
  Cc: fot at autox.team.net 
  Sent: Monday, June 15, 2015 10:33 PM
  Subject: Re: [Fot] TR4 High speed driveline vibration


  FOTer's,
  I will assume this car has the stock style trans mount, not the later TR6 style setup...yeah I know about assuming anything, but here I go.
  In order to keep the rear of the trans where it belongs and yet allow some movement and inslulation this is the mod I have utilized.
  Remove the 2 trans to mount bolts and drill straight down thru those mounting holes thru the small trans crossmember. Enlarge those new holes in that crossmember to about 5/8" or so. Purchase 2 new bolts that are treaded all the way and are long enough to go thru the trans, the trans mount and the crossmember. Drop the bolt thru the trans and trans mount and start a nut up the bolt to tighten the trans to the mount. The bolt will now extend thru the trans, the mount (tighten the nut securely to hold them together) and the crossmember. Use a large washer and a nyloc on the bolt where it now extends thru the crossmember. Tighten this nylock only until it "just" contacts the crossmember. Because the bolt is smaller than the hole you just drilled it will allow the trans to move a small distance in any direction, but will stop any excessive movement, including saving the radiator in event of a serious impact!

  Clear as mud?

  A little out of balance in Nor Cal
  Nick





  -----Original Message-----
  From: Duncan Charlton <duncan.charlton54 at gmail.com>
  To: toodamnfunky <toodamnfunky at comcast.net>
  Cc: fot <fot at autox.team.net>
  Sent: Mon, Jun 15, 2015 12:23 pm
  Subject: Re: [Fot] TR4 High speed driveline vibration


  Jim, 


  How are your motor and trans mounts?  If they allow the engine/gearbox combo to shift out of line when under high torque, the u-joints could move out of proper alignment, but then when power is reduced, things would shift back into position.  If you put the car on jackstands and run it to this rpm in top gear (might not be a bad idea to remove the drive wheels and tires if you’re sure they’re balanced) there won’t be much load on the engine, so if the vibration is due to deformation of the mounts, the vibration should not appear.


  Duncan




    On Jun 15, 2015, at 10:55 AM, toodamnfunky at comcast.net wrote:


    FoT,

    I have a driveline vibration that doesn't start up until I get to about 95- 100 MPH. I figured I would start with the driveshaft
    before looking into the diff or OD/trans. I have an IRS car with Richard Good CV axles and hubs so it's very un likely its that but
    I will inspect them. I'm wondering if anybody has any advice on high speed vibration diagnosis or detection.
    What I'm wondering is even if it is the driveshaft how would I know with it sitting on my bench. 
    Any help would, as always be greatly appreciated.
    Jim g
    _______________________________________________







_______________________________________________ fot at autox.team.net  http://www.fot-racing.com  Donate: http://www.team.net/donate.html Archive: http://www.team.net/archive Forums: http://www.team.net/forums Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/malaboge@aol.com   

------------------------------------------------------------------------------


  _______________________________________________
  fot at autox.team.net

  http://www.fot-racing.com

  Donate: http://www.team.net/donate.html
  Archive: http://www.team.net/archive
  Forums: http://www.team.net/forums
  Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/william.tobin31@verizon.net


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/fot/attachments/20150616/675e87bd/attachment-0001.htm>