[Fot] Cutting Aeroquip Hoses..

[Joe Boruch]

Greg's conversion as noted below are still holding up very well.  Joe(B)

   I converted my old street TR4 to Aeroquip lines with AN fittings.
Intially, I use the hose clamps to
   hold the line on the carbs.This wasn't a good solution. The Aeroquipped
line wasn't as flexible as
   the rubber hose and caused one of the brass fittings on the float bowl
lid to fatigue and break. It
   was the only time in 17 years my `4 didn't get me home. Fortunately, I
was just across town. I
   had a local machine shop weld aluminum AN fittings on the carbs. From
then on it was "plain
   sailing'.

   OBTW, you can use a Dremel tool cut off wheel to get through the braid,
then any good utility
   knife will get you through the "rubber". The Dremel will give you a
cleaner cut with less "prickly
   bits"

   YMMV

Greg Petrolati Champaign, Illinois

That's not a leak... My car's just marking its territory...






>From: "Kramer, Robert" <RKramer at rdoequipment.com>
>To: "steve" <colordog.1 at earthlink.net>, "FOT" <fot at autox.team.net>
>Subject: Re: [Fot] Cutting Aeroquip Hoses..
>Date: Fri, 16 Mar 2007 08:20:05 -0500
>
>I used the TFE hose and high presssure fittings for the fuel system in
>my TR4A. I bought all the pieces from Speedway Motors online. The links
>are listed below. The neat thing about this stuff is that you can easily
>make up sections in lengths you need as you go. I don't know how many
>pieces I made from my dual outlet, 2 pump system to the regulator under
>the hood, but it looks great. I have a bulkhead fitting for the main
>line where it goes through the firewall and another for the coolant line
>from my fuel pressure gauge isolator. The fittings are reusable and the
>hose doesn't have a 5 second rule like rubber encapsulated stuff. I used
>electrical tape and a cut-off wheel, blow out the dust and used silicone
>grease to ease assembly. The only worry is crimping if you bend it too
>tightly. Have a look.
>
>http://www.speedwaymotors.com/p/936,81_High-Pressure-Hose-Ends.html
>http://www.speedwaymotors.com/p/940,81_Stainless-Wire-BTFEandB-Braided-H
>igh-Pressure-Hose.html
>
>Bob Kramer
>Sales Manager
>RDO Equipment Co.
>16415 North IH 35
>Pflugerville, TX 78660
>512-272-4141
>Fx 512-272-9365
>
>-----Original Message-----
>From: fot-bounces at autox.team.net [mailto:fot-bounces at autox.team.net] On
>Behalf Of steve
>Sent: Thursday, March 15, 2007 7:12 PM
>To: FOT
>Subject: [Fot] Cutting Aeroquip Hoses..
>
>~Steve
>_______________________________________________
>Fot mailing list
>Fot at autox.team.net
>http://autox.team.net/mailman/listinfo/fot
>_______________________________________________
>Fot mailing list
>Fot at autox.team.net
>http://autox.team.net/mailman/listinfo/fot

_________________________________________________________________
Get a FREE Web site, company branded e-mail and more from Microsoft Office
Live! http://clk.atdmt.com/MRT/go/mcrssaub0050001411mrt/direct/01/
_______________________________________________
Fot mailing list
Fot at autox.team.net
http://autox.team.net/mailman/listinfo/fot



_____________________________________________________________________
Interested in getting caught up on today's news?
Click here to checkout USA TODAY Headlines.
http://track.netzero.net/s/lc?s=198954&u=http://www.usatoday.com/news/front.h
tm?csp=24