[Fot] plug wires

Bill Babcock BillB at bnj.com
Tue Jul 10 15:04:14 MDT 2007


I just did a posting to AllAluminumTour.com . things are going well, I'm in
Pittsburgh for the PVGP. BeaveRun last weekend was fun. Ran with the
groundpounders. Had a blast. Sure surprised those guys. Having a car that
stops and turns is quite an advantage.

BTW, I'm listening to the Egypt lectures for a second time. Diane wasn't with
me the first time through. We're up to lecture 44, damn it. only 4 more to go.
Bob Brier is a national treasure. sort of a Dick Feynman of Archeology.


-----Original Message-----
From: Kas Kastner [mailto:kaskas at cox.net]
Sent: Tue 7/10/2007 2:03 PM
To: Bill Babcock
Subject: Re: [Fot] plug wires

Yes it does, you traveling devil.  How is it going?  Got a couple of your
reports but I sure everyone would like a little more.

Never Be beaten by Equipment
Kas Kastner
  ----- Original Message -----
  From: Bill Babcock
  To: Walter Hollowell ; Scott Janzen ; fot at autox.team.net
  Sent: Tuesday, July 10, 2007 1:52 PM
  Subject: Re: [Fot] plug wires


  BP6 _E_S, does the TR6 have 3/4" reach plugs??


  -----Original Message-----
  From: fot-bounces at autox.team.net on behalf of Walter Hollowell
  Sent: Tue 7/10/2007 9:16 AM
  To: 'Scott Janzen'; fot at autox.team.net
  Subject: Re: [Fot] plug wires

  My TR6 also runs a Mallory dual point mechanical advance  distributor that
  has been recurved to better match the hot cam. I use a Mallory racing coil
  called a Promaster.  I am running 10.5:1 compression, big valves in a head
  that is extensively ported. Roller rockers, headers. I am using NGK non
  resistor spark plugs part number BP6ES. I have triple Webers. I found that
  the following spark wire kit works very well. It is made by a company
called
  Taylor. It is 8mm Spiro Pro with the 135 degree boots. Part number 73653. I
  paid $59.95 for this kit a a local speed shop.
  My engine brings 173 hp to the ground on a chassis dyno at 5,500 ft
  elevation.
  Good luck
  Walt Hollowell
  Abq., NM

  -----Original Message-----
  From: fot-bounces at autox.team.net [mailto:fot-bounces at autox.team.net] On
  Behalf Of Scott Janzen
  Sent: Tuesday, July 10, 2007 8:18 AM
  To: fot at autox.team.net
  Subject: [Fot] plug wires

  I'm looking to install the optimum performance plug wires for my GT6,
  running a Mallory dual point distributor and a Bosch coil.  the car is
  prepped for vintage racing. Any recommendations and sources?
  walt at hot-tr6.com
  Fot mailing list
  Fot at autox.team.net
  http://autox.team.net/mailman/listinfo/fot
  billb at bnj.com
  Fot mailing list
  Fot at autox.team.net
  http://autox.team.net/mailman/listinfo/fot
  _______________________________________________
  http://www.team.net/donate.html

  kaskas at cox.net
  Fot mailing list
  Fot at autox.team.net
  http://autox.team.net/mailman/listinfo/fot



More information about the Fot mailing list