<div dir="auto">Hello again Friends,<div dir="auto">   The following is an abbreviated story, with pictures, of the resurrection of my TR6 engine. The car hadn't run in decades, I am told, but the engine looked pretty good. Here's a first look. </div><div dir="auto"><br></div><div dir="auto"><a href="http://aubard.us/75_Triumph/P1000408.JPG" target="_blank" rel="noreferrer">http://aubard.us/75_Triumph/P1000408.JPG</a><br></div><div dir="auto"><br></div><div dir="auto">   First step was to pull the plugs, squirt in about 1cc of oil, and turn the engine over by hand. Everything turned smoothly. I next changed the oil and filter, connected a battery, pulled the fuses out, and spun the engine for a second or two on the starter. Everything turned smoothly. </div><div dir="auto">   Next step, a compression test. Given a 1975 U.S. specification engine with a compression ratio of 7.75:1, the perfect static pressure would be about 114psi. My engine's <span style="font-family:sans-serif">initial (cold) compression readings are:</span></div><div dir="auto"><br>
</div><div dir="auto"><font color="#f44336"><b>1  115 psi<br>
2  106 psi<br>
3  103 psi<br>
4  111 psi<br>
5  102 psi<br>
6  111 psi</b></font><br></div><div dir="auto"><font color="#f44336"><b><br></b></font></div><div dir="auto">   Considering that this engine hadn't run in ages and the condition of the valve and their seats was unknown, I decided to <u>not</u> open the engine unless further tests indicated that doing so was warranted. </div><div dir="auto">   I next removed the valve cover and found a clean rocker shaft and springs. And with the cover of off, I cleaned and refinished it. Lots of other bits got cleaned and refinished at the same time.</div><div dir="auto">   The waterpump and thermostat were replaced. All hoses are new. The radiator was flushed and pressure tested. A new fan belt was installed and the cooling system was flushed.</div><div dir="auto">   The Z-S carbs were rebuilt and reinstalled on new gaskets. The fuel line was disconnected and flushed clean. The tank was boiled out and no corrosion was found.</div><div dir="auto">   Earlier I posted a picture or two of the electric fuel pump I used. Here's one of the pictures again.</div><div dir="auto"><br></div><div dir="auto"><a href="http://aubard.us/75_Triumph/20190722_091448.jpg" target="_blank" rel="noreferrer">http://aubard.us/75_Triumph/20190722_091448.jpg</a><br></div><div dir="auto"><br></div><div dir="auto">   I removed all the non-functional emissions bits including the air injection plumbing. The pipe fittings on the manifold were not coming off by any means known to man so...I sawed off the pipes and plugged them with bolts and ultra high temperature cement. Here's how they looked before  'surgery'.</div><div dir="auto"><br></div><div dir="auto"><a href="http://aubard.us/75_Triumph/20190514_091212.jpg" target="_blank" rel="noreferrer">http://aubard.us/75_Triumph/20190514_091212.jpg</a><br></div><div dir="auto"><br></div><div dir="auto">   Before going on and on, as I am want to do, here is the engine and it's bay. This is before balancing the carbs and installing the refinished air cleaner with a new element. It now starts easily and runs great!</div><div dir="auto"><br></div><div dir="auto"><a href="http://aubard.us/75_Triumph/20190515_120747.jpg" target="_blank" rel="noreferrer">http://aubard.us/75_Triumph/20190515_120747.jpg</a><br></div><div dir="auto"><br></div><div dir="auto">   I've left out the bit about omitting a waterpump bolt and causing a leak. And probably other little issues like a new alternator, but you get the gist.</div><div dir="auto"><br></div><div dir="auto">Rick</div></div>