[6pack] 6pack Digest, Vol 64, Issue 11
COLIN THOM
colinthom at shaw.ca
Thu May 14 13:34:53 MDT 2020
Thank you, Mark!
With all that damage, please don't worry about a 1 hour lag in email transmission. In these times, that's hardly relevant.
Be safe
Colin
From: 6pack-request at autox.team.net
To: 6pack at autox.team.net
Sent: Thursday, May 14, 2020 11:00:03 AM
Subject: 6pack Digest, Vol 64, Issue 11
Send 6pack mailing list submissions to
6pack at autox.team.net
To subscribe or unsubscribe via the World Wide Web, visit
http://autox.team.net/mailman/listinfo/6pack
or, via email, send a message with subject or body 'help' to
6pack-request at autox.team.net
You can reach the person managing the list at
6pack-owner at autox.team.net
When replying, please edit your Subject line so it is more specific
than "Re: Contents of 6pack digest..."
Today's Topics:
1. Possible Team Net outage (Mark J Bradakis)
2. Re: Possible Team Net outage (andrew uprichard)
3. Re: rear shock conversion (Richard)
4. Re: rear shock conversion (Richard)
----------------------------------------------------------------------
Message: 1
Date: Wed, 13 May 2020 16:00:36 -0600
From: Mark J Bradakis <mark at bradakis.com>
To: list 6pack <6pack at autox.team.net>
Subject: [6pack] Possible Team Net outage
Message-ID: <92d765a1-cbc1-393b-15fa-34be71cb1b08 at bradakis.com>
Content-Type: text/plain; charset=utf-8; format=flowed
We had some severe wind gusts in Salt Lake Monday afternoon, about half
of a large tree blew over, sort of hitting the garage and some cars.?
Take a look at http://bradakis.com/net_wire.jpg to get an idea of what
happened.? Inside that marked off area you can see a black wire.? That
is Team Net's connection to the world. Getting all the fallen branches
off that wire is beyond my capabilities.? We've contacted some
professional tree removers, haven't heard back yet, so not sure when the
mess will be cleaned up.
So basically if we get more wind gusts over the next day or two all that
debris could shift and take out that network cable.? And Team Net would
be off the air for who knows how long.? So be aware of that
possibility.? If it happens, you might be seeing a status message from
hoosierq at gmail.com that may look suspicious at first glance.? It will be
from me.
And another note, the old problem of delayed email seems to be occurring
again.? Currently the delay is one the order of an hour or so, I'll be
looking into the situation.
Fun times indeed!
mjb.
------------------------------
Message: 2
Date: Wed, 13 May 2020 18:52:26 -0400
From: "andrew uprichard" <auprichard at uprichard.net>
To: "'Mark J Bradakis'" <mark at bradakis.com>
Cc: <triumphs at autox.team.net>, <6pack at autox.team.net>
Subject: Re: [6pack] Possible Team Net outage
Message-ID: <013a01d62979$2d5783a0$88068ae0$@uprichard.net>
Content-Type: text/plain; charset="utf-8"
But were the cars OK??
Andrew
-----Original Message-----
From: 6pack <6pack-bounces at autox.team.net> On Behalf Of Mark J Bradakis via 6pack
Sent: Wednesday, May 13, 2020 6:01 PM
To: list 6pack <6pack at autox.team.net>
Subject: [6pack] Possible Team Net outage
We had some severe wind gusts in Salt Lake Monday afternoon, about half of a large tree blew over, sort of hitting the garage and some cars. Take a look at http://bradakis.com/net_wire.jpg to get an idea of what happened. Inside that marked off area you can see a black wire. That is Team Net's connection to the world. Getting all the fallen branches off that wire is beyond my capabilities. We've contacted some professional tree removers, haven't heard back yet, so not sure when the mess will be cleaned up.
So basically if we get more wind gusts over the next day or two all that debris could shift and take out that network cable. And Team Net would be off the air for who knows how long. So be aware of that possibility. If it happens, you might be seeing a status message from hoosierq at gmail.com that may look suspicious at first glance. It will be from me.
And another note, the old problem of delayed email seems to be occurring again. Currently the delay is one the order of an hour or so, I'll be looking into the situation.
Fun times indeed!
mjb.
_______________________________________________
Support Team.Net http://www.team.net/donate.html Suggested annual donation $12.96
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
6pack at autox.team.net
http://autox.team.net/mailman/listinfo/6pack
Unsubscribe/Manage: http://autox.team.net/mailman/options/6pack/auprichard@uprichard.net
------------------------------
Message: 3
Date: Wed, 13 May 2020 15:55:41 -0700
From: Richard <taylorturbo6 at yahoo.com>
To: Mitchel Seff <ms6453 at gmail.com>
Cc: 6pack <6pack at autox.team.net>
Subject: Re: [6pack] rear shock conversion
Message-ID: <95F204D4-DACD-482E-822B-042F705A051A at yahoo.com>
Content-Type: text/plain; charset=utf-8
Ah Mitch....you cheated!!
Dick
> On May 13, 2020, at 3:32 PM, Mitchel Seff <ms6453 at gmail.com> wrote:
>
> I agree with Dicks explanation of preparation and function. I?m not denying the failures but rather try and understand why each particular failure happened. I have also had the VB tube shock bracket with KYB gas shock on my car for over twenty years with out any failure or sign of metal fatigue. I also took the extra precaution of adding a support bracket.
> <image0.jpeg>
>
> <image1.jpeg>
>
>
>
> Mitch Seff
>
>>>> On May 12, 2020, at 4:47 PM, Richard Taylor via 6pack <6pack at autox.team.net> wrote:
>>> ?My message here, as told before on different TR6 forums, is that if one wants to convert from lever shocks to tube shocks, it is prudent that when the trailing arm rises the trailing arm bump stop(s) take the force, and not the shock attachment points. This can be checked by removing the road spring and manual lifting the TA up to see where contact is made. In my case, when done approx. 10 years and around 70,000 miles ago. A 1/8 inch spacer was added where it screws to the new TA bump rubbers. Also some shifting around to the shock bump rubbers, so that there was room left in the shock stroke when hard contact was made between the bump stop and the bump rubbers. Also note here that i?m running the ?semi-comp? road springs, so it?s not often that all of the spring compression takes place.
>>> I write this not to defend the tube shock conversion, but to show that this conversion needs to be checked out to be sure the above takes place. And no, the attachment point from my conversion has never torn loose or welded at any time. I do view this area each time the road wheel is removed for some other reason.
>>> So far as what I look for regarding shock operation is not all that scientific. Just press down with my weight on the rear fenders several times and watch the action, I want both bounce and rebound to show a good damping effect.
>>> In place is the KYB silver shock conversion, purchased from VB. (A birthday gift from my bride of 30 years)
>>>
>>> Dick
>>>> On May 12, 2020, at 7:56 AM, Glenn Franco via 6pack <6pack at autox.team.net> wrote:
>>> The rear shock conversion sold by the likes of Moss Motors, TRF, Vicky Brit, and others is likely going to result in the shock crossmember being fractured at the weld to the frame. I have fixed a few of these and this is a well known failure mode. The best practice if you are going to use these is to fashion a diagonal brace from the upper shock mount 45 deg down to the frame. I have seen some made from angle but I made a number of these from 1" thick wall tube.
>>> The problem with this conversion is its to simple to attach but it imparts fore aft loads on the crossmember that causes fractures and then if fails completely and detaches from the frame.
>>> The lever shocks do not cause fore aft loads and therefore no issues. We just had another club member suffer such a failure of the shock crossmember.
>>> If you ever have to fix one of these your in for a treat since not only does it pull away from the frame but it tends to twist that crossmember.
>>> This bracket should not be confused with the one TRF sold that the upper shock mount attaches to the inner rear wheel well. That one has its own issues.
>>> Good luck with that
>>> Glenn
>>> _______________________________________________
>>> Support Team.Net http://www.team.net/donate.html
>>> Suggested annual donation $12.96
>>> Archive: http://www.team.net/archive
>>> Forums: http://www.team.net/forums
>>> 6pack at autox.team.net
>>> http://autox.team.net/mailman/listinfo/6pack
>>> Unsubscribe/Manage: http://autox.team.net/mailman/options/6pack/taylorturbo6@yahoo.com
>>
>> _______________________________________________
>> Support Team.Net http://www.team.net/donate.html
>> Suggested annual donation $12.96
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>>
>> 6pack at autox.team.net
>> http://autox.team.net/mailman/listinfo/6pack
>>
>> Unsubscribe/Manage: http://autox.team.net/mailman/options/6pack/ms6453@optonline.net
------------------------------
Message: 4
Date: Wed, 13 May 2020 15:55:41 -0700
From: Richard <taylorturbo6 at yahoo.com>
To: Mitchel Seff <ms6453 at gmail.com>
Cc: 6pack <6pack at autox.team.net>
Subject: Re: [6pack] rear shock conversion
Message-ID: <95F204D4-DACD-482E-822B-042F705A051A at yahoo.com>
Content-Type: text/plain; charset=utf-8
Ah Mitch....you cheated!!
Dick
> On May 13, 2020, at 3:32 PM, Mitchel Seff <ms6453 at gmail.com> wrote:
>
> I agree with Dicks explanation of preparation and function. I?m not denying the failures but rather try and understand why each particular failure happened. I have also had the VB tube shock bracket with KYB gas shock on my car for over twenty years with out any failure or sign of metal fatigue. I also took the extra precaution of adding a support bracket.
> <image0.jpeg>
>
> <image1.jpeg>
>
>
>
> Mitch Seff
>
>>>> On May 12, 2020, at 4:47 PM, Richard Taylor via 6pack <6pack at autox.team.net> wrote:
>>> ?My message here, as told before on different TR6 forums, is that if one wants to convert from lever shocks to tube shocks, it is prudent that when the trailing arm rises the trailing arm bump stop(s) take the force, and not the shock attachment points. This can be checked by removing the road spring and manual lifting the TA up to see where contact is made. In my case, when done approx. 10 years and around 70,000 miles ago. A 1/8 inch spacer was added where it screws to the new TA bump rubbers. Also some shifting around to the shock bump rubbers, so that there was room left in the shock stroke when hard contact was made between the bump stop and the bump rubbers. Also note here that i?m running the ?semi-comp? road springs, so it?s not often that all of the spring compression takes place.
>>> I write this not to defend the tube shock conversion, but to show that this conversion needs to be checked out to be sure the above takes place. And no, the attachment point from my conversion has never torn loose or welded at any time. I do view this area each time the road wheel is removed for some other reason.
>>> So far as what I look for regarding shock operation is not all that scientific. Just press down with my weight on the rear fenders several times and watch the action, I want both bounce and rebound to show a good damping effect.
>>> In place is the KYB silver shock conversion, purchased from VB. (A birthday gift from my bride of 30 years)
>>>
>>> Dick
>>>> On May 12, 2020, at 7:56 AM, Glenn Franco via 6pack <6pack at autox.team.net> wrote:
>>> The rear shock conversion sold by the likes of Moss Motors, TRF, Vicky Brit, and others is likely going to result in the shock crossmember being fractured at the weld to the frame. I have fixed a few of these and this is a well known failure mode. The best practice if you are going to use these is to fashion a diagonal brace from the upper shock mount 45 deg down to the frame. I have seen some made from angle but I made a number of these from 1" thick wall tube.
>>> The problem with this conversion is its to simple to attach but it imparts fore aft loads on the crossmember that causes fractures and then if fails completely and detaches from the frame.
>>> The lever shocks do not cause fore aft loads and therefore no issues. We just had another club member suffer such a failure of the shock crossmember.
>>> If you ever have to fix one of these your in for a treat since not only does it pull away from the frame but it tends to twist that crossmember.
>>> This bracket should not be confused with the one TRF sold that the upper shock mount attaches to the inner rear wheel well. That one has its own issues.
>>> Good luck with that
>>> Glenn
>>> _______________________________________________
>>> Support Team.Net http://www.team.net/donate.html
>>> Suggested annual donation $12.96
>>> Archive: http://www.team.net/archive
>>> Forums: http://www.team.net/forums
>>> 6pack at autox.team.net
>>> http://autox.team.net/mailman/listinfo/6pack
>>> Unsubscribe/Manage: http://autox.team.net/mailman/options/6pack/taylorturbo6@yahoo.com
>>
>> _______________________________________________
>> Support Team.Net http://www.team.net/donate.html
>> Suggested annual donation $12.96
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>>
>> 6pack at autox.team.net
>> http://autox.team.net/mailman/listinfo/6pack
>>
>> Unsubscribe/Manage: http://autox.team.net/mailman/options/6pack/ms6453@optonline.net
------------------------------
Subject: Digest Footer
_______________________________________________
6pack mailing list
6pack at autox.team.net
http://autox.team.net/mailman/listinfo/6pack
------------------------------
End of 6pack Digest, Vol 64, Issue 11
*************************************
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/6pack/attachments/20200514/8e961c2e/attachment-0001.htm>
More information about the 6pack
mailing list