[6pack] 6pack Digest, Vol 23, Issue 6

rnorris1 at swbell.net rnorris1 at swbell.net
Mon Aug 15 14:56:52 MDT 2016 

Regarding the high rpm issue, while indeed the issue may be the carbs in which case just discard this reply. In the case of my '75, the cause of a 2000 rpm idle turned out to be worn springs on the distributor or maybe it was just nasty inside. When all other remedies failed and it was obvious that the distributor was at issue, I sent it off or rebuild and it now idles perfectly.
Just sayin',  Rick Norris 

    On Monday, August 15, 2016 1:43 PM, "6pack-request at autox.team.net" <6pack-request at autox.team.net> wrote:
 

 Send 6pack mailing list submissions to
    6pack at autox.team.net

To subscribe or unsubscribe via the World Wide Web, visit
    http://autox.team.net/mailman/listinfo/6pack
or, via email, send a message with subject or body 'help' to
    6pack-request at autox.team.net

You can reach the person managing the list at
    6pack-owner at autox.team.net

When replying, please edit your Subject line so it is more specific
than "Re: Contents of 6pack digest..."


Today's Topics:

  1. High RPM, won't come down (COLIN THOM)


----------------------------------------------------------------------

Message: 1
Date: Sun, 14 Aug 2016 13:30:16 -0600 (MDT)
From: COLIN THOM <colinthom at shaw.ca>
To: 6pack at autox.team.net
Subject: [6pack] High RPM, won't come down
Message-ID: <1275839532.58583735.1471203016225.JavaMail.root at shaw.ca>
Content-Type: text/plain; charset="utf-8"

Glenn 


Your high RPM is likely caused by a few things occurring at once. The pistons hanging up in a high position will certainly do it. That lets more fuel into the carb throat. The throttle shaft seals are probably worn so the carbs are sucking in air from there. Add the extra fuel to that extra air, and there's your problem. Changing the o-rings in the pistons is a must-do but get ready for a rebuild. The rebuild kit includes new bushings for the throttle shafts. I've never done it, but I've wondered if spraying some white grease onto the throttle shafts where they enter/exit the carb body might temporarily seal the air leak caused by worn seals, or even better, cause the seals to expand a bit. Might be worth a shot. 


Colin 
74-1/2 

----- Original Message -----

From: 6pack-request at autox.team.net 
To: 6pack at autox.team.net 
Sent: Friday, August 12, 2016 11:00:01 AM 
Subject: 6pack Digest, Vol 23, Issue 4 

Send 6pack mailing list submissions to 
6pack at autox.team.net 

To subscribe or unsubscribe via the World Wide Web, visit 
http://autox.team.net/mailman/listinfo/6pack 
or, via email, send a message with subject or body 'help' to 
6pack-request at autox.team.net 

You can reach the person managing the list at 
6pack-owner at autox.team.net 

When replying, please edit your Subject line so it is more specific 
than "Re: Contents of 6pack digest..." 


Today's Topics: 

1. high RPM, won't come down (Glenn Rattmann) 
2. Re: Damaged top (alan salvatore) 


---------------------------------------------------------------------- 

Message: 1 
Date: Tue, 09 Aug 2016 12:20:19 -0700 
From: Glenn Rattmann <k6na at cts.com> 
To: 6pack at autox.team.net 
Subject: [6pack] high RPM, won't come down 
Message-ID: <201608091920.u79JKQaC016898 at mail40c28.carrierzone.com> 
Content-Type: text/plain; charset="us-ascii"; format=flowed 

Gents, 
The car is 74.5 with stock Strombergs (175 CD-2 SE) and stock engine, . 
The last carb rebuild by me was probably 2002, but maybe only 4,000 
miles since then. My occasional driver; it has about 105k miles on 
it. The car had one DPO, he did a valve job at aroung 75k 
miles. I'm certain carb shaft bushings were never re-done. 

Problem is-- Engine hot, after a few minutes of stopandgo driving, I 
might reach say 3500 RPM in normal shift sequences. When I let off 
the throttle during shifting, or want to decelerate, the RPM 
sometimes stays at the high peak-- like 3500! A few frantic kicks of 
the pedal will "usually" bring things down to normal idle-- but it's 
dicey. There is no stumble on acceleration. 

I have inspected the action of the pedal/carb linkage when car is at 
rest, and nothing there seems amiss. So I don't think the linkage is 
hanging up somewhere (externally). 

Dashpots are losing oil 'too quickly' and I always have to top them 
up after the car sits for extended periods (weeks) following, say, a 
90 mile drive. Yesterday I pulled the air cleaner for a look, and 
noticed both carbs have oily gunk on the piston and the contact area 
of the carb bottom interface The rear one is worse than the front 
one. Not much doubt that the bypassing oil is responsible for the 
gunk-- but can the gunk be the cause of the symptom? 

After some carb cleaner spray, and cleaning out the reachable areas, 
and adding some oil, I notice the pistons lift normally, falling with 
a normal 'click' . Prior to the cleaning, the pistons didn't fall 
normally, but were hanging up slightly when falling. 

I pulled the carb tops and lifted out the 
diaphragm/piston/needle. The diaphragms seem ok to me (no obvious 
tears or cracks) and the alignment tab was correct. I suppose 
"pinholes" could be there, but not visible...? Pistons look fine, 
the needles are straight and move correctly against their spring 
action internally. 

I have some spare o-rings for the dashpot oil chambers so today I 
will install them. Could the leaking oil and subsequent gunk I 
mentioned be the cause of the throttle staying high, as 
described? If so, then the cleaning plus adding the new o-ring on 
each dashpot should eliminate the problem. Any comments appreciated. 

I'm aware that anything beyond this procedure (relatively easy, carbs 
remain on car) will likely require pulling the carbs . Then we are 
looking at things like butterfly hang-up... float behavior...float 
valve... bypass valves... and so on, right? 

Who sells the best quality float assembly replacement? And which 
vendor's carb rebuild kits are "best", which partly means "they 
include the dashpot o-ring" as they should. ISTR years ago, some 
kits didn't have that o-ring. 

Thanks, 

Glenn/San Diego 
74.5 




------------------------------ 

Message: 2 
Date: Fri, 12 Aug 2016 07:41:48 -0400 
From: alan salvatore <alansalvy at gmail.com> 
To: "otral at juno.com" <otral at juno.com> 
Cc: "6pack at autox.team.net" <6pack at autox.team.net> 
Subject: Re: [6pack] Damaged top 
Message-ID: 
<CAAAEehQ8kVbKxZ=qsKit_hpBTnP9=xjMYdoQ2FDcMKb7=JutvQ at mail.gmail.com> 
Content-Type: text/plain; charset="utf-8" 

If it was just a tear in the vinyl you could put a patch behind it. 
With the window separating, I guess I would toss it and buy new. 
Al 

On Tue, Aug 9, 2016 at 11:13 AM, otral--- via 6pack <6pack at autox.team.net> 
wrote: 

> What are my options? 
> 
> 1. Buy a new top or, 
> 
> 2. Try to repair. (what are the products you guys recommend?) 
> 
> Note: my cracks are at the fold ( passenger side window) that include 
> tears and partial separation of the plastic window from the vinyl and small 
> tear in the vinyl top at the fold. 
> 
> Alan Graffam in Windsor Locks, CT. 74 French Blue 
> ____________________________________________________________ 
> WAHC 
> Durban Millionaire Exposes How He Earns R1079/Hour from Home 
> http://thirdpartyoffers.juno.com/TGL3131/57a9f36c76888736c41bast01duc 
> _______________________________________________ 
> Support Team.Net http://www.team.net/donate.html 
> Suggested annual donation $12.96 
> Archive: http://www.team.net/archive 
> Forums: http://www.team.net/forums 
> 
> 6pack at autox.team.net 
> http://autox.team.net/mailman/listinfo/6pack 
> 
> Unsubscribe/Manage: http://autox.team.net/mailman/ 
> options/6pack/alansalvy at gmail.com 
> 
> 
-------------- next part -------------- 
An HTML attachment was scrubbed... 
URL: <http://autox.team.net/pipermail/6pack/attachments/20160812/39e29361/attachment-0001.html> 

------------------------------ 

Subject: Digest Footer 

_______________________________________________ 
6pack mailing list 
6pack at autox.team.net 
http://autox.team.net/mailman/listinfo/6pack 


------------------------------ 

End of 6pack Digest, Vol 23, Issue 4 
************************************ 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/6pack/attachments/20160814/ce63ed00/attachment-0001.html>

------------------------------

Subject: Digest Footer

_______________________________________________
6pack mailing list
6pack at autox.team.net
http://autox.team.net/mailman/listinfo/6pack


------------------------------

End of 6pack Digest, Vol 23, Issue 6
************************************


  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/6pack/attachments/20160815/4c911c2d/attachment.html>

More information about the 6pack mailing list