[6pack] Floorpan replacement and Rust repair quote...

Wed Jun 10 06:34:16 MDT 2015

I will not comment on the rust... but I have been running silicon for over 20 years and had no issues. when i first switched over i completely rebuilt everything including new stainless brake lines. I am also running silicon in the clutch. Did have to replace the master cylinder about 5 years back, but I see no difference at all and had no unusual problems. I even used to autocross a couple of times a year.
Robert 74TR6
      From: alan salvatore via 6pack <6pack at autox.team.net>
 To: James_ <jattr6 at hotmail.com> 
Cc: 6pack at autox.team.net 
 Sent: Tuesday, June 9, 2015 6:40 PM
 Subject: Re: [6pack] Floorpan replacement and Rust repair quote...

If the outer edges of the floor pan is good then you can cut and patch in a new floor pan.
If not then tub off.
If inner rocker is bad, tub off.
Depends on where the bad area is.
I am doing one now that had a small area but it ran under the firewall and the frame was also in the way. Plus I wanted to blast the frame, so we took the body off.
I can see 10K with paint for floors, battery box, would have to see inner fender.
I have been putting silicone in every TR6 that crosses my path for the last 15 years.
AlOn Jun 9, 2015 4:55 PM, "James_ via 6pack" <6pack at autox.team.net> wrote:

Hi all…
First….I am so depressed - I may sell the TR6 and walk away….seriously…even after 22 years of my entire adult life.
I just met and got a quote from a guy that generally works on Austin Healey's…and I gather he does very high end work….and accustom to people with deep pockets.So that was probably my mistake, but still is probably the best approach to have work done 100% thorough and correct.
First: I was told floor pans require the car body to be off the frame to replace.First overwhelming thought…body of the car? ugh.
Second: I have a few bad spots of rust that need panels fabricated and welded. The worse is under the master cylinder and rust haseaten through the inner and outer wheel arch. It affects the pedal box too.(I can send a picture if anyone is interested)
So the guy was really wanting the body removed, sand blasted, panels repaired and powder coated.Sounds awesome. But it all gets down to time and money. a LOT of money and the rest of the year.Roughly, looking at $10-20K. for a TR6. yikes. Not sure I love the car that much. I know repairing old cars will ALWAYS cost more than a car is worth.I know that. Don't lecture about that. But...my rust is not a 'rust bucket' by any means. And for $20K I can find a car that comes close to showroom condition!!!
I guess I am so depressed / disappointed / overwhelmed / sad / hmmmm….what else…
…I am at a loss as to what to do. One option: Say screw it and live with the rotten areas, put the car back to gather and drive it.or:Sell the dang thing and walk away. Maybe I finally reached that "mercy…mercy…no more…make it stop" stage.- I doubt I could bring myself to buy a TR6 again….I mean, what's the point. Mine isn't THAT awful and  I know the history of THIS car.
Or:another option….(my original desire/thought) is to have the areas repaired and new floor boards installed by someone that does a really good welding job but not nearly as intense of a procedure or expensive. I know…you get what you pay for. 
This winter: I removed everything from the engine to detail it out and everything is ready to go back in once the rust was fixed and engine bay painted.At this point, I may as well sell off all the PARTS - they'd be worth more they the car as a whole at this point. And everything is removed!(only half kidding….)

Oh, one more thing….this guy is DEAD set against my thought of switching to Silicone brake fluid. I mean, DEAD set against and talking about warranty being voided if I use it.I looked at him and said: "What Warranty is that?" "It isn't like there is a dealership I can go to" "I buy parts, I put them on." I am the warranty department!He mentioned the warranty of the parts I buy from Moss, etc. hmmmm….They void it if the silicone falls the parts.Really? Moss SELLS Silicone brake fluid. I suspect all this is because his DAD is against Silicone and he just follows what his dad hates. 
I was recently curious why auto stores don't seem to carry DOT 5 Silicone as much as the other types. So now with this restoration guy's comments…is Silicone THAT bad/poorly rated?
Well, any advice or words of comfort?
James
1976 TR6 

_______________________________________________
Support Team.Net http://www.team.net/donate.html
Suggested annual donation  $12.96
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

6pack at autox.team.net
http://autox.team.net/mailman/listinfo/6pack

Unsubscribe/Manage: http://autox.team.net/mailman/options/6pack/alansalvy@gmail.com

_______________________________________________
Support Team.Net http://www.team.net/donate.html
Suggested annual donation  $12.96
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

6pack at autox.team.net
http://autox.team.net/mailman/listinfo/6pack

Unsubscribe/Manage: http://autox.team.net/mailman/options/6pack/robertrudolphi@yahoo.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/6pack/attachments/20150610/1dd10a79/attachment-0001.html>