spridgets
[Top] [All Lists]

Re: [Spridgets] Sprite Mirror bracket

To: Weslake1330 <weslake1330@gmail.com>
Subject: Re: [Spridgets] Sprite Mirror bracket
From: Allen Hefner via Spridgets <spridgets@autox.team.net>
Date: Tue, 5 Nov 2019 10:14:44 -0500
Cc: Spridgets <spridgets@autox.team.net>
Delivered-to: mharc@autox.team.net
Delivered-to: spridgets@autox.team.net
References: <CAMhoh1XV76VAeY43vLf9YdM7X91Y_fv+bezBzjz1DRv0+J40TA@mail.gmail.com>
--===============8283865480925010948==

--000000000000104ffa05969ae57d

Daniel,

It looks like you would have enough room to fit a cup holder on the
trailing end of the bracket! I found that there isn't enough room inside
the car for one.

Allen Hefner
Norristown, PA
Sun City Center, FL

*Current:*
2016 Subaru outback somewhere
2006 Chebbie
*Former:*
1963 Sunbeam Alpine Series III
1967 Triumph TR4A IRS
1964 VW Type I
1967 VW Type II
1967 Rover 2000TC
1977 MG Midget (Sniff!)


On Sat, Nov 2, 2019 at 2:45 PM Weslake1330 via Spridgets <
spridgets@autox.team.net> wrote:

> Hi List,
>
> I've just finished making my first mirror bracket.  Well actually it's the
> second because I abandoned the first one part finished as it wasn't quite
> right.  I'm pleased with the end result but I'll be making another one as
> this one isn't quite perfect.  Yep, it does stick out a bit from the
> bodywork (just under 3 inches) but its supposed to because being close to
> the car's bodywork makes it much less aerodynamic (air sees a bigger bulge
> than the actual mirror).  Very wet here so it may be a week before it gets
> road tested - the worst that can happen is that it vibrates and I need to
> use thicker aluminum sheet (this was 1.2mm) or stainless steel sheet.
>
> Photos attached.
>
> Regards
>
> ------------------------
>
> spridgets@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Suggested annual donation: $12.75
>
> Archive: http://www.team.net/pipermail/spridgets
> http://autox.team.net/archive
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/spridgets/lbc77mg@gmail.com
>

--000000000000104ffa05969ae57d
Content-Transfer-Encoding: quoted-printable

<div dir=3D"ltr">Daniel,<div><br></div><div>It looks like you would have en=
ough room to fit a cup holder on the trailing end of the bracket! I found t=
hat there isn&#39;t enough room inside the car for one.=C2=A0<br clear=3D"a=
ll"><div><div dir=3D"ltr" class=3D"gmail_signature" data-smartmail=3D"gmail=
_signature"><div dir=3D"ltr"><div><div dir=3D"ltr"><div><div><br></div><div=
>Allen Hefner</div>
<div>Norristown, PA</div><div>Sun City Center, FL</div>
<div>=C2=A0</div>
<div><em>Current:</em></div>
<div>2016 Subaru outback somewhere</div><div>2006 Chebbie</div>
<div><em>Former:</em></div>
<div>1963 Sunbeam Alpine Series III</div>
<div>1967 Triumph TR4A IRS</div>
<div>1964 VW Type I</div>
<div>1967 VW Type II</div>
<div>1967 Rover 2000TC</div>
<div>1977 MG Midget (Sniff!)</div></div></div></div></div></div></div><br><=
/div></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_a=
ttr">On Sat, Nov 2, 2019 at 2:45 PM Weslake1330 via Spridgets &lt;<a href=
=3D"mailto:spridgets@autox.team.net";>spridgets@autox.team.net</a>&gt; wrote=
:<br></div><blockquote class=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.=
8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir=3D"lt=
r">Hi List,<div><br><div><div>I&#39;ve just finished making my first mirror=
 bracket.=C2=A0 Well actually it&#39;s the second because I abandoned the f=
irst one part finished as it wasn&#39;t quite right.=C2=A0 I&#39;m pleased =
with the end result but I&#39;ll be making another one as this one isn&#39;=
t quite perfect.=C2=A0 Yep, it does stick out a bit from the bodywork (just=
 under 3 inches) but its supposed to because being close to the car&#39;s b=
odywork makes it much less aerodynamic (air sees a bigger bulge than the ac=
tual mirror).=C2=A0 Very wet here so it may be a week before it gets road t=
ested - the worst that can happen is that it vibrates and I need to use thi=
cker aluminum sheet (this was 1.2mm) or stainless steel sheet.</div><div><b=
r></div><div>Photos attached.</div><div><br></div><div>Regards</div></div><=
div><br></div></div></div>
------------------------<br>
<br>
<a href=3D"mailto:spridgets@autox.team.net"; target=3D"_blank">spridgets@aut=
ox.team.net</a><br>
<br>
et=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/spridgets"; rel=3D"norefer=
rer" target=3D"_blank">http://www.team.net/pipermail/spridgets</a>=C2=A0 <a=
 href=3D"http://autox.team.net/archive"; rel=3D"noreferrer" target=3D"_blank=
">http://autox.team.net/archive</a><br>
<br>
ets/lbc77mg@gmail.com" rel=3D"noreferrer" target=3D"_blank">http://autox.te=
am.net/mailman/options/spridgets/lbc77mg@gmail.com</a><br>
</blockquote></div>

--000000000000104ffa05969ae57d--

--===============8283865480925010948==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

------------------------

spridgets@autox.team.net


Archive: http://www.team.net/pipermail/spridgets  http://autox.team.net/archive


--===============8283865480925010948==--

<Prev in Thread] Current Thread [Next in Thread>