shop-talk
[Top] [All Lists]

Re: [Shop-talk] Cutting up fiberglass

To: Neil Sherry <neiljsherry@talktalk.net>, shop-talk@autox.team.net
Subject: Re: [Shop-talk] Cutting up fiberglass
From: old dirtbeard <dirtbeard@pacbell.net>
Date: Fri, 26 Apr 2013 11:49:10 -0700 (PDT)
Delivered-to: mharc@autox.team.net
Delivered-to: shop-talk@autox.team.net
References: <OF39BBD232.A5767857-ON85257B59.004ACBAC-85257B59.004C646E@mail.megageek.com> <517AC8B6.7080208@talktalk.net>
Strip it and leave the hull by the side of the road with a "free" sign.  I 
think 
it would disappear...

best,

doug




----- Original Message ----
From: Neil Sherry <neiljsherry@talktalk.net>
To: shop-talk@autox.team.net
Sent: Fri, April 26, 2013 11:34:45 AM
Subject: Re: [Shop-talk] Cutting up fiberglass

My Thoughts. Don't do it!
By all means strip and sell the fittings. But then with the hull:

    List it on ebay - for $5 - someone might take it away and save you
    the trouble of cutting it up! Or even keep it!
    It could be used in a playground for kids to climb over, turned
    upside down as a shed/playhouse, maybe a college could use it for
    structural testing analysis. It could be sunk in the ground as a
    pond, filled with soil and planted with flowers/vegetables (think
    jumbo window box - maybe at the side of the road outside your
    property). Or the front 8 ft could be cut off and stood up to form a
    sheltered seat - like this
    http://farm4.staticflickr.com/3187/2845782678_53ab5c3efb_z.jpg?zz=1

If you get really desperate, maybe break it up with a machine 
(backhoe/bulldozer etc) rather than cutting might work



On 26/04/2013 14:42, eric@megageek.com wrote:
> Ok, I have a 23' sailboat that I need to get rid of.  Here are my
> options...
>
> 1-Sell it complete for maybe a $100-$200 (trailer included.)(Note, the
> boat needs work.)
> 2-Part it out and sell the components, then get rid of the hull.  (I'm
> estimating about $700-$1200 worth of parts)
> 3-Donate it complete
>
> I was opting for #2.  If I go that route, I have to cut up the boat.  It's
> a single skin (no insulation or foam) hull.  I have a 2yd dumpster that I
> could put pieces in each week.
>
> If I cut it, can I use a chainsaw without damaging the saw (I'm not that
> concerned about the blade, I'll just use an old one.)
>
> If I wet the boat as I'm cutting, will this damage the saw?
>
> I've tried in the past to use a recip saw, but it took forever.  What
> about a carbide tip cir-saw or dia grinder?
>
> Any advice?
>
>
>
> Eric P
> "Be as beneficent as the sun or the sea, but if your rights as a rational
> being are trenched on, die on the first inch of your territory." Ralph
> Waldo Emerson
> _______________________________________________
>
> Shop-talk@autox.team.net
> Donate: http://www.team.net/donate.html
> Suggested annual donation  $12.96
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage: 
>http://autox.team.net/mailman/options/shop-talk/neiljsherry@talktalk.net
_______________________________________________

Shop-talk@autox.team.net
Archive: http://www.team.net/archive
http://autox.team.net/mailman/options/shop-talk/dirtbeard@pacbell.net
_______________________________________________

Shop-talk@autox.team.net
Archive: http://www.team.net/archive

<Prev in Thread] Current Thread [Next in Thread>