mg-t
[Top] [All Lists]

Re: [Mg-t] Fwd: Shaved Head

To: gunnellj@athenet.net
Subject: Re: [Mg-t] Fwd: Shaved Head
From: Bob Howard <mgbob@juno.com>
Date: Wed, 22 Apr 2009 09:59:14 -0400
John,
   Be of good cheer.  When you get the rocker assy back in place you can
figure out the necessary length of pushrod. Once you know that, it's easy
to shorten a pushrod. Pushrods are really push-tubes with fitted ends. 
One end can be pulled off and you use a "parting tool" in a lathe to
shorten the tube.   When I rebuilt my XPAG a decade back, Moss was out of
the short pushrods, sent the long ones, and a friend shortened them for
me in a half hour. 
Bob

On Wed, 22 Apr 2009 09:40:05 -0400 gunnellj@athenet.net writes:
> ----- Forwarded message from  -----
>       Date: Wed, 22 Apr 2009 09:38:33 -0400
>       From: gunnellj@athenet.net
>       Reply-To: gunnellj@athenet.net
>       Subject: Shaved Head
>       To: Mg-t@autox.team.n
> 
> 
> Hey Mates
> 
> I am trying to figure out which push rods I need for my MG TD engine 
> build. Or rather, in the "real world" situation, if I can safely 
> still use the "long" push rods Moss sells. I say this because they 
> no longer have the short push rods. 
> 
> The Moss catalog states the factory head depth is 3.022. The shop 
> resurfaced mine. My mechanic says it measures out with a very slight 
> taper, but within spec, and averages 3.00 inches. So is my head 
> "excessively" thinner to the point where the "long" push rods won't 
> work?
> 
> Moss says that they now have only the long push rods. The rep told 
> me that Crane is out of business and no longer making push rods. I 
> checked Crane's Website. Sure enough. Today (April 22) they are 
> auctioning off all their inventory, equipment and intellectual 
> property rights. Since they make the T-series camshaft that Moss 
> sells, I don't know the implications of this to the T-Series 
> community. 
> 
> As far as my situation at present, I have the head torqued down and 
> the rocker arm assembly has been sent to Rocker Arm Specialists. So 
> I hope I do not have to go with two head gaskets and I cannot tell 
> you is my rocker arm assembly has the long or short adjusting 
> screws. 
> 
> 
> John Gunnell
> 
> 
> 
> ----- End forwarded message -----
> _______________________________________________
> 
> Support Team.Net  http://www.team.net/donate.html
> 
> Mg-t@autox.team.net
> http://autox.team.net/mailman/listinfo/mg-t
> 
> Archives at http://www.team.net/archive
> 
> 
 
____________________________________________________________
Online Trading - Get the latest information on trading online. Click Now
http://thirdpartyoffers.juno.com/TGL2141/fc/BLSrjpTFOsXKkTFFI80A1i8Ysav31IRIIi8T5crv6WG9UKzOX45kgcQWp8E/
_______________________________________________

Support Team.Net  http://www.team.net/donate.html

Mg-t@autox.team.net
http://autox.team.net/mailman/listinfo/mg-t

Archives at http://www.team.net/archive

<Prev in Thread] Current Thread [Next in Thread>